DRAPER 29779, 29792 Preparing 5/7 Drawer Trolley Instruction Manual

DRAPER 29779, 29792 Preparing 5/7 Drawer Trolley

Product Information

5 / 7 Drawer Trolley (Stock No. 29779 / 29792)

The 5 / 7 Drawer Trolley is a storage unit designed to store and organize tools, equipment, and other items. The trolley comes with handles, bumpers, and castors for easy mobility. The castors require annual maintenance with high-quality bearing grease. The surfaces of the trolley should be periodically cleaned with a mild detergent and water. Grease and oil can be removed with most standard cleaning fluids. Auto wax can be used to preserve the storage unit’s luster finish and protect against scratches.

Assembly Instructions

1. Attach handles to the front angled side with 4 pieces of M8 x 20mm bolt. Do not fully tighten.
2. Attach bumpers to the side panel with 4 pieces of M4 x 10mm bolt. Do not fully tighten.
3. Attach castors to the bottom of the unit with 16 pieces of M8 x 20mm bolt. Do not fully tighten.

To remove and replace drawers, follow the manufacturer’s instructions.

Preparing 5 / 7 Drawer Trolley

Attach Handles

• Attach handles to front angled side with 4 pieces of M8 x 20mm bolt.
• Do not fully tighten.
• To make assembly easier we recommend having two persons aid one another in assembly.

Attach Bumpers

• Attach bumpers to side panel with 4 pieces of M4 x 10mm bolt.
• Do not fully tighten.

Attach Castors

• Attach castors to the bottom of unit with 16 pieces of M8 x 20mm bolt.
• Do not fully tighten.

REMOVING AND REPLACING THE DRAWERS:

• Pull the drawer completely out
• Press down the left tab and lift up the right tab
• Pull drawer off sliders
• To reinstall the drawer, realign with the internal drawer slider and push in until locked in place

MAINTENANCE

CASTOR MAINTENANCE

• Grease the castors annually using high-quality bearing grease.

CARE AND CLEANING

• Periodically the surfaces should be cleaned with a mild detergent and water. Grease and oil can be removed with most standard cleaning fluids. For safety, use a non-flammable cleaning fluid.
• Auto wax will preserves the storage unit’s luster finish and protects against scratches.

Preparing Door Tall Cabinet

Preparing 1 Door Tall Cabinet

To make assembly easier we recommend having two persons aid one another in assembly.

Parts

CABINET CONNECTION

• Connect the side panels of two cabinets with (4) bolt M6 x 16mm and nut M6, and tighten with phillips screwdriver (not included).

Note: remove the drawers and open the doors before cabinet connection.

STEP 1

• Attach back panel (item 5) to left and right side panels (item 3 and 4) by engaging the holes on the left and right side panels with the corresponding hooks on back panel.

STEP 2

• Insert the top panel (item 1) into the side and back panels.
• Lay the cabinet flat on the ground if necessary.

STEP 3

• Insert the bottom panel (item 2) into the side and back panels. Lay the cabinet flat on the ground if necessary.

STEP 4

• Use packaging material to protect the unit. Attach the leg leveller (item 11) to foot holder (item 10).
• Insert bolt M8 x 16mm (item 12) through the foot holder into the cabinet.

STEP 5

• Attach the front and side kick panel (item 7 and 8) to foot holder with bolt M6 x 16mm (item 13).

STEP 6

• Obliquely place the four shelf panels (item 9) in the cabinet, secure the shlef panels at four desired heights by carefully inserting the shelf edges into the flanges on left and right side panels. Make sure each shelf is level.

STEP 7

Place the flat washer (item 14) into the hinge pin, align the hinge pin on the bottom of the door with the hole on bottom panel, slowly and carefully insert the hinge pin into the hole. Algin the hinge pin on the top of the door with the hole on top panel, slowly and carefully insert the hinge pin into the hole.

Preparing 2 Door Tall Cabinet

To make assembly easier we recommend having two persons aid one another in assembly.

Parts

CABINET CONNECTION

• Connect the side panels of two cabinets with (4) bolt M6 x 16mm and nut M6, and tighten with phillips screwdriver (not included).

Note: remove the drawers and open the doors before cabinet connection.

STEP 1

• Place the left back panel (item 5) and right back panel (item 6) together on a level surface.
• Attach right back panel to left back panel by engaging the holes on the left back panels with the corresponding hooks on right back panel.

STEP 2

• Attach left and right back panels to left and right side panels (item 3 and 4) by engaging the holes on the side panels with the corresponding hooks on back panels.

STEP 3

• Insert the top panel (item 1) into the side and back panels. Lay the cabinet flat on the ground if necessary.

STEP 4

• Insert the bottom panel (item 2) into the side and back panels. Lay the cabinet flat on the ground if necessary.

STEP 5

• Use packaging material to protect the unit. Attach the leg leveller (item 13) to foot holder (item 12). Insert bolt M8 x 16mm (item 14) through the foot holder into the cabinet.

STEP 6

• Attach the front and side kick panel (item 9 and 10) to foot holder with bolt M6 x 16mm (item 15).

STEP 7

• Obliquely place the four shelf panels (item 11) in the cabinet, secure the shlef panels at four desired heights by carefully inserting the shelf edges into the flanges on left and right side panels. Make sure each shelf is level.

STEP 8

Place the flat washer (item 16) into the hinge pin, algin the hinge pin on the bottom of the door with the hole on bottom panel, slowly and carefully insert the hinge pin into the hole. Algin the hinge pin on the top of the door with the hole on top panel, slowly and carefully insert the hinge pin into the hole.Repeat the step above to complete the right door assembly.

Installing Worktop

• To make assembly easier we recommend having two persons aid one another in assembly.
• Place the worktop on cabinets, align the pre-drilled holes in worktop with holes in cabinets, secure bolt M6 x 16mm through the top of the cabinets into the worktop pre-drilled holes.

Installing Back Panel

Installing Back Panel / Wall Cabinet with Wall Brackets (Single & Double)

To make assembly easier we recommend having two persons aid one another in assembly.

• STEP 1: Attach wall bracket (single and double) to cabinet with bolt M8 x16mm, washer 18 x 8 x 1mm and spring washer 14 x 8.8 x 2.6mm, and tighten with wrench (not included).
• STEP 2: Attach back panel to wall bracket (single and double) with bolt M6 x 16mm, nut M6 and spring washer 12 x 6.5 x 0.8mm, and tighten with wrench (not included).
• STEP 3: Attach wall cabinet to wall bracket (single and double) with bolt M8 x 16mm, flat washer 8 x 8 x 1mm and spring washer 14 x 8.8 x 2.6mm, and tighten with wrench (not included)
• STEP 4: Connect the side panels of two cabinets with M6 x 16mm and nut M6, and tighten with wrench (not included).

CABINET CONNECTION

• Connect the side panels of two cabinets with (4) bolt M6 x 16mm and nut M6, and tighten with wrench (not included).

Note: remove the drawers and open the doors before cabinet connection.

Installing Wall Bracket

• Attach wall bracket (double) to back panel with (10) bolt M6 x 16mm, nut M6 and flat washer 12 x 6.5 x 0.8mm, and tighten with wrench (not included).
• Attach wall bracket (double) to wall cabinets and base cabinets / trolley with (8) bolt M8 x 16mm, flat washer 18 x 8 x 1mm and spring washer 14 x 8.8 x 2.6mm, and tighten with wrench (not included).
• Attach wall bracket (single) to back panel with (5) bolt M6 x 16mm, nut M6 and flat washer 12 x 6.5 x 0.8mm,and tighten with wrench (not included).
• Attach wall bracket (single) to wall cabinets and base cabinets / trolley with (4) bolt M8 x 16mm, flat washer 18 x 8 x 1mm and spring washer 14 x 8.8 x 2.6mm, and tighten with wrench (not included).

Draper Tools Limited

• drapertools.com
• Hursley Road, Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF UK.

References

• Draper Tools Official Website | Hand Tools, Power Tools and Accessories

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>