MIXX OX2 MOTH On Ear Wireless Headphones User Guide
- June 5, 2024
- MIXX
Table of Contents
OX2 MOTH On-Ear Wireless Headphones
User Guide
BOX CONTAINS
*Ear caps will come pre installed on the headphones -if ordered separately a second set of printed back caps may be included in the box.
HEADPHONE CONTROLS
- Ear Cap (Interchangeable design)
- Volume Up / Skip Button
- Volume Down / Previous Button
- Microphone
- Multi-function Button
- LED Light
- Micro USB Port
CONTROL FUNCTIONS
First Time Pairing| Press and hold the button until you hear ‘MOTH headphones,
hello’. Go to Bluetooth settings on your phone and select ‘MOTH On Ear’ from
the list. Once paired successfully you will hear ‘MOTH headphones connected’.
---|---
Play/Pause| Short press the Button
Volume Up/Down| Short Press the Buttons to adjust the volume
Previous / Skip Tracks| Press and hold the Buttons to change tracks
Answer / End Call| Short press the Button
Activate Voice
Assistant| Double press the button to activate Siri or Google Assistant
Listen for the familiar Voice Assist ‘beep’ then ask a question or state a
command
Decline a Phone Call| Double press the for an incoming call
Power ON/OFF| Press and hold the button for 3 seconds until you hear ‘MOTH
headphones hello/MOTH headphones goodbye’
PLUG AND PLAY
Plug the Micro USB to 3.5mm connector audio cable supplied into the Micro USB Port 7 and the 3.5mm connector into the 3.5mm socket of your audio device to listen to your sound through your headphones.
CHARGING THE HEADPHONES
Connect the headphones to a suitable USB wall charger, computer USB port, or a
power bank using the micro USB to USB charging cable supplied.
The MOTH On Ear will begin to charge automatically, and the LED Light
Indicator 6 will light up RED.
Once the headphones are fully charged, the RED light will switch off. This can
take between 1 and 2 hours.
INTERCHANGEABLE EAR CAPS
You can change the design of your headphones with interchangeable ear caps
(sold separately).
To remove the ear cap, ease your fingernail into slot 8 between the ear
cup and the headphone base and gently push away from the headphones.
Take your new designed MOTH On-Ear earcap, check inside the ear cap to read
which side it fits on (Left or Right) and align it to the correct headphone
base. Gently push the ear cap onto the headphone base until you hear it
‘click’.
The newly designed ear caps should now be safely secured to the headphones.
SAFETY INSTRUCTIONS
It’s important that you read this section completely, especially the
‘Warnings, Caution and Safe Usage’ instructions.
For your protection:
Ensure the product is correctly connected using the manufacturer’s original
accessories included.
Please keep the product out of reach from children and animals.
Do not listen to loud music for a long duration of time.
Adjust the volume to a comfortable level before listening.
Do not use headphones while operating machinery, including cars.
Do not use in areas where the use of hearing is required for safety.
Do not drop, short circuit, disassemble or continue to use this product if
damaged.
We recommend
To refer all servicing to qualified persons.
Servicing may be required when the product has been damaged in any way, does
not operate normally or has been dropped.
The operating temperature range for this product is 5° – 40° Celsius.
Warning
These headphones and the micro USB cable connectors are not water resistant
and should not be exposed to rain, moisture, any splashing or liquid spills.
Caution: This product contains a Lithium battery. Incorrect disposal of this
battery may result in an explosion.
RECYCLE
This product can be recycled.
Products bearing this symbol must NOT be thrown away with normal household
waste.
Take the product to a collection point designated for the recycling of
electronic devices.
Find out more about return and collection points through your local authority.
SAFE USAGE INFORMATION
Do not crush, puncture or incinerate the headphones.
Only use a certified or the device manufacturer’s charging cable.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirements.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>