globe GE50240 Smart Wi-Fi LED Outdoor User Guide

Thank you for selecting Globe as your smart home solution. WO proper care, this product will provide years of pleasure and enjoyment.
SMART WI-FI-LED OUTDOOR SECURITY FLOODLIGHT
Check out the installation video on our website: globe- electric.com/smart

WHAT’S IN THE BOX

SPECIFICATIONS

• Lumens:1600
• Color temperature: 2200 – 5000 K
• Dimmable: 0 -100%
• Motion detection: up to 21 m (68.89 ft)
• 240 °detection zone
• Protection: IP44
• Input/Hardwired 120V AC
• Power consumption:10VA
• IP distance:10 m (32.8 ft)
• Bit rate: 32Kps-2Mbps
• Audio: 2-way
• Wireless range: 50 m (164.04 ft)
• Field of view:110°
• Operating Temperature: -20 °C-50 °C
• Wi-Fi standard: IEEE802.11b/g/n
• Frequency: 2.4 Ghz-2.4835 GHz
• Wi-Fi security: WPA-PSK/WPA2-PSK
• Data security: AES 128

FEATURES

With the Globe Smart Outdoor Floodlight, you can get live view HD video on your smartphone and hear or speak to visitors through the Globe Suite app. Motion detection and video recording capability to capture up to 24 days with a 128 GB SD card (not included).

LED
Indicator Light| Red Light (Solid): Floodlight’s network is unstable
Red Light (Flashing rapidly): Floodlight is in pairing mode Green Light (Solid): Floodlight is connected
Green Light (Flashing rapidly): Floodlight is connecting to the network
---|---
SD Card| Supports micro SD Card storage (Max.1 28GB)
Microphone| Audio in
Speaker| Audio out
Reset| Press and hold the reset button down for 5 seconds. Once you hear an audible click sound, it means your floodlight has been set to factory settings, and it is now ready to connect. If the indicator is not flashing red rapidly, repeat.

TOOLS REQUIRED

FOR YOUR SAFETY

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY. Please read these instructions carefully prior to installation. Failure to follow any of these instructions could void product warranties. Globe Electric assumes no responsibility for claims arising out of improper or careless installation.
CAUTION:
Do not install close to flames or flammable gases. Keep away from children.
Do not install on an unstable surface/position.
Do not stare directly at the light while it is on. To prevent the unit from falling, install the base unit tightly with an anchor.
Do not install in close proximity to other light sources.
MAINTENANCE: Ensuring the lamp is kept clean will optimize performance.
** Most electrical accidents are caused by carelessness or ignorance. If you combine a basic knowledge of electricity, a healthy respect for it, and a dose of common sense, you can safely tackle many household electrical repairs. Here are some basic guidelines for working with electricity: Before working on a circuit, go to the main service panel and remove the fuse or trip the breaker that controls that circuit. Tape a sign to the panel warning others to leave the circuit alone while you work. Before touching any wire, use a voltage tester to make sure it’s not live. Whenever you check for voltage in a receptacle, check both outlets – each may be controlled by a separate wiring circuit. When replacing fuses, turn off the main power first. Make sure your hands and feet are dry, and place one hand behind your back to prevent electricity from making a complete circuit through your chest. Touch a plug fuse only by its insulated rim. Remove cartridge fuses with a fuse puller. Use tools with insulated handles and ladders made of wood or fiberglass. Keep dry- chemical fire extinguishers in the kitchen, basement, and workshop. Never disable grounding devices. Make sure that all appliances requiring grounding are properly grounded, and that the electrical system itself is properly grounded. Meet or exceed all electrical code requirements that cover the work you are doing. Always work with enough light to see what you are doing; it’s easy to make mistakes when you’re working in dim light. When in doubt about the safety of any electrical repair or test, call in a professional.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE THE CORRECT BRANCH CIRCUIT CONDUCTOR.**

FIG.1 Place the wall switch to the “OFF” position.
Depending on which type of fuse box you have in your home:
FIG. 2 Place either the main (Master) switch to the “OFF” position, cutting off power to your entire home, or turn off the individual switch that provides power to where the fixture will be installed.
OR
FIG. 3 Place either the main (Master) switch to the “OFF” position, cutting off power to the entire home or unscrewing the fuse that provides power to where the fixture will be installed.

INSTALLATION

CAUTION: When choosing the mounting location, make sure the LED light illuminates the desired area and that the product will not be directly exposed to rain.

1. Installing the Mounting Bracket
   Line up the holes on the mounting bracket(C) with the holes on your junction box using the two junction box screws (C). Secure the mounting bracket to the junction box.
   

2. Making the Electrical Connections
   Connect the light fixture wires to the junction box wires with a wire nut (D). If your wires from the junction box are not long enough, and you cannot make a direct connection to the plate, please extend the wires. Place the wires in the wire terminal. There are wire indicators on the plate. Secure the wires by tightening the screw with a flat tip screwdriver.
   white to white black to black-green ground wire to house ground
   Note: Ensure the polarity is correct

3. Installing the Mounting Plate
   Place the mounting plate (F) against the junction box. When mounting to a wall, the “UP” arrow must be pointed upward. When mounting to an eave, the “UP” arrow must be pointed toward the building. Insert the small mounting bolt (B) through the mounting plate (F) hole and mounting bracket (G) hole. Tighten the bolt (B) securely. Firmly pull on the mounting plate (F) to verify it is securely attached to the mounting bracket(G)
   
   INSTALLATION (CONTINUED)
   CAUTION: Do not cut any wires with factory-installed wire connectors or remove the wire connectors

4. Mounting the Floodligh t
   Align the bottom edge of the floodlight (H) with the bottom edge of the mounting plate (F). Tilt the floodlight (H) toward the mounting plate (F), making sure the floodlight (H) is centered on the mounting plate (F). Tighten the large mounting bolt (A) securely through the center of the mounting plate (F). Do not overtighten Push the rubber plug (E) firmly into the large mounting bolt hole on the floodlight (H).
   

5. Sealing
   Caulk completely around the area where the canopy meets the wall surface with silicone caulking compound to prevent water from seeping into the outlet box
   Note: The unit should be mounted 61/z to 10′ (2 to 3 m) from the ground to ensure motion detection is optimized

OPERATION

CAUTION: LED LAMPS ARE NON-REPLACEABLE. Do not attempt to access/maintain the LEDs. Any contact may damage the LEDs and will void the warranty.
Adjusting the lamp heads and sensor

• The lamp’s heads and sensor can be easily adjusted. You may adjust them left, right, up, or down to get the desired lamp direction.

CONNECTING INSTRUCTIONS

1 Let’s get started!

• Download the Globe SuiteTM app from the App Store or Google Play to your mobile device.

• Launch the Globe Suite app.

• To register, enter your email address. Create a password, then log in to the app. OR

• Login if you already have an account.
  2 Verify your network

• Verify your network and ensure your mobile device is connected to a 2.4 GHz Wi-Fi channel.

• Consult your router documentation for detailed instructions on how to change wireless settings.

3. Add a device

• Power on your smart floodlight.

• Once plugged in, the floodlight should be flashing rapidly.

• If it is not flashing rapidly, press and hold the reset button for 5 seconds.

• Select the “+” symbol on the top right-hand corner.

• Select your product type and follow the instructions within the app.

• If the connection fails, try using a QR code.
  Add a device: QR code

• On the “Add a device” page select the QR code on the top right-hand corner and follow the instructions within the app.

• If the connection fails, try scan mode.
  Add a device: Scan mode

• Select the “+” symbol on the top right-hand corner.

• Select “Scan”.

• Follow instructions within the app.

• You’re good to go!

4. Set up voice assistance

• Instructions in the Globe Suiten.’ app: Select “Profile”, select “INtegration”, choose your voice assistant, and follow instructions.

Did you know? Most modern routers are dual-band meaning they support both 2.4 GHz and 5 GHz channels.
The most common wireless options are:

• Mixed: The router will broadcast both 2.4 GHz and 5 GHz simultaneously under the same SSID. The device will choose which to connect to based on multiple variables (congestion, distance to router, etc.).
• 2.4 GHz: Broadcast only on this channel.
• 5 GHz : Broadcast only on this channel.
• Dual 2.4 and 5 GHz using separate SSIDs: Pouter will broadcast both channels and the user manually decides which to connect to.

Since 1932, Globe has taken pride in offering products of the highest quality, and a level of service unparalleled in the industry. Should you encounter any difficulties, have any questions or simply wish to offer us your valuable feedback, you may contact us in the following ways: Toll-Free Telephone:1-888-543-1388 (North America Only) /Toll-Free Fax:1-800-668-4562 (North America Only) E-Mail: info@globe-electric.com/ Mail: Globe Electric Customer Service Department 150 Oneida, Montreal, Quebec, Canada FOP 1A8 Please visit our website to discover other quality Globe products: http✓/www.globe-electric.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>