Shenzhen Do Intelligent Technology 7042 Smart Watch User Manual
- June 5, 2024
- Shenzhen Do Intelligent Technology
Table of Contents
Shenzhen Do Intelligent Technology 7042 Smart Watch
Bind Watch
-
Download and install App
You can set up the watch through the VeryFitPro app for iOS or Android devices. The steps are shown as follows:
Notes: The hardware platform of the equipment system shall meet requirements. -
Bind process
-
Turn on the Bluetooth and GPS on your mobile phone
-
Find the binding request on the pull-down list on the home page of the APP
Notes:
During the binding process, VeryFitPro will prompt you to enable GPS and
Bluetooth, and authorize VeryFitPro to get access to the GPS on you mobile
phone.
iPhones will not prompt you with any information unless you complete Bluetooth
pairing on your ID205L watch in the built-in Bluetooth in you mobile phone
after binding.
Synchronous Data
In daily wear, the watch can detect all kinds of product data. The user needs to connect the watch with Bluetooth on the APP before synchronous operation. The detailed operations are shown as follows: Open the mobile APP> swipe down the page> sync prompt appears
Notes!
Please synchronize the data at least once within 7 days to avoid data loss at
the watch end.
The Apple phone also needs to be connected to the paired watch in the
Bluetooth setting interface of the mobile phone, so that the watch can be
alerted. The steps are shown as follows:
Open the IOS phone > set > Bluetooth > search and click pair
Instruction for Use
-
Charging schematic
Connect and charge the watch according to the picture. It needs to be charged to activate the watch when it is started for the first time. -
Wear/install
Tip: Wearing too loosely may affect the accuracy of heart rate data.
Operating Instructions
-
Definition of key function
-
Watch dial switch
Replacing the dial interface will appear after long-pressing the dial. -
Main interface operation
Swipe the screen to enter different interfaces (interactive interface tile diagram)
Function Introduction
-
Icon function introduction Notes: For more functions (sleeping) and operations, please check the VeryFitPro software of the mobile phone.
-
Start sports
-
Enter sports
Click the sports icon > select the sports type > enter the sports countdown automatically -
During sports
Pause sports: short press the right key Restore sports: short press the right key -
End sports
End sports: long-press the right key> select the end button on the screen
Product Parameters
Cleaning and Maintenance
It is recommended to wear and maintain according to the following three points:
- Keep the product clean;
- Keep the product dry;
- Do not wear it too tight.
Do not use household cleaners to clean the watch, but use the soap-free detergent.
It is recommended to use alcohol to scrub stains that are not easy to remove.
Frequently Asked Questions
-
The Mobile APP search for the watch failed
-
It is recommended to update VeryFitPro to the latest version.
-
It is recommended to close all programs, restart the Bluetooth, and then connect.
-
Confirm whether the mobile phone system meets Android 4.4 or IOS 8.0 or above.
-
The watch received no alerts, text messages or phone calls
-
You need to turn on the smart reminder function and the call reminder switch in the APP, and synchronize to the watch.
-
The iPhone needs to be paired with the watch via Bluetooth. (Please check the column of “Synchronous Data” for details)
-
You need to keep your watch connected to Bluetooth.
-
Bluetooth is often disconnected
-
If the distance between the watch and the mobile phone is too far, the connection effect of more than 7m Bluetooth is obviously weakened.
-
Whether there is a shield between the watch and the mobile phone, the human body, wearing metal jewelry, etc., will interfere with the Bluetooth connection signal.
-
Whether the Bluetooth function of the mobile phone is abnormal.
-
About data backup
The data of the watch is synchronized at least once every 7 days to the mobile phone (the watch end only keeps the data of the last 7 days). -
How to restart and restore factory settings
Shutdown operation: Watch > set > shutdown/right-key restart
Restore factory settings: connect the watch to APP > open APP device model > more settings -
Do I need to keep my Bluetooth on when I wear my watch?
-
For the three functions, i.e. counting steps, sleeping and alarm clock, you do not need to connect the watch to the mobile phone all the time. If you only need to wear a watch when you exercise, you can connect the watch and your mobile phone to view the data synchronously after the exercise.
-
For the functions of call alert, message alert, find the phone, you need to turn on the mobile phone’s Bluetooth, and maintain the connection with the mobile phone.
Cycling Warning
Please maintain good judgment at all times and ride in a safe manner. Make sure your bike and hardware are properly maintained, and all components are properly installed.
Matters Needing Attention
- Watch data needs to be kept once every 7 days to avoid data loss.
- The watch has no waterproof effect on seawater, acidic and alkaline solutions, chemical reagents and other corrosive liquid. The damage or defects caused by misuse or improper use are not covered by the warranty.
- Sports mode supports up to 6 hours of exercise at a time.
- The watch has a waterproof level of IP68 and supports cold water shower, swimming, but not diving.
- Avoid wearing the watch too tight in daily use. Please keep the parts of the watch touching the skin dry.
- When your heart rate is measured, keep your arm still during the test.
FCC Rules
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could avoid the user’s authority to operate the equipment. This
equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS
Old electrical appliances must not be disposed of together with the residual
waste, but have to be disposed of separately. The disposal at the communal
collecting point via private persons is for free. The owner of old appliances
is responsible to bring the appliances to these collecting points or to
similar collection points. With this little personal effort, you contribute to
recycling valuable raw materials and the treatment of toxic substances.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>