Sena M1 Mountain Bike Helmet User Manual

M1 Mountain Bike Helmet
User Manual

M1 Mountain Bike Helmet

Charging
Red LED: Charging
Blue LED: Fully charged
Power On/Off
Power On: Press and hold the (+) Button and Center Button for 1 second
Power Off: Tap the (+) Button and Center Button.
Volume Adjustment
(+) Button – Increase the volume
(-) Button – Decrease the volume
Battery Check

Phone, Music Pairing
Initially Pairing the M1
The Bluetooth system will automatically enter the phone pairing mode when you initially turn on the Bluetooth system or in the following situation:
• Rebooting after executing Factory Reset

1. Press and hold the Center Button and (+) Button for 1 second.
2. Search for Bluetooth devices on your mobile phone. Select the M1 in the list of the devices detected on the mobile phone.
3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.

Music Operation

Play or pause music: Press the Center Button for 1 second.
Trackback: Press the (-) Button for 1 second.
Track forward: Press the (+) Button for 1 second.
Mobile Phone Call Making and Answering
Answering a call: Tap the Center Button
Ending a call: Press the Center Button for 2 seconds.
Voice dial: Press the Center Button for 3 seconds.
Speed dial: Press the (+) Button for 3 seconds.
Rejecting a call: Press the (+) Button for 2 seconds.

Intercom

Intercom Pairing

1. Press and hold the Center Button of two headsets for 5 seconds until the red LEDs of both units start to flash rapidly.
2. Simply tap the Center Button of any one of the two headsets.

Intercom Start/End: Tap the Center Button
Radio On/Off
Turn on the FM radio: Press the (-) Button for 1 second.
Turn off the FM radio: Press the (-) Button for 1 second.
Radio Scan Up FM Band
Start scanning: Press the (+) Button for 1 second.
Stop scanning: Press the (+) Button for 1 second.
Radio Move to Preset Station
Move to the next preset: Press the Center Button for 1 second (1 2 10)
Radio Seek Stations
Seek up stations: Double-tap the (+) Button.
Seek down stations: Double-tap the (-) Button.
LED Taillight
LED On and Solid -> Night Flash -> Day Flash -> LED Off: Tap the Sena Button

Setting

Configuration Menu: Press the Center Button for 15 seconds.

Troubleshooting

Factory Reset
If you want to restore the headset to factory default settings, use the Factory Reset in the configuration menu. The headset automatically restores the default settings and turns off.
Certification and Safety Approvals FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antennae
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Exposure Statement
The highest SAR value reported under this standard during product certification for use next to the head with the minimum separation distance of 0mm is 0.6W/Kg. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. This product is in compliance with FCC RF exposure requirements and refers to the FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID: S7A-SP81, IC:8154A-SP81.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>