Shenzhen Doageas Technology T9 Headset Water Cup User Manual

Shenzhen Doageas Technology T9 Headset Water Cup User Manual

• Vacuum technology long-term thermal insulation.
  

• 304 stainless steel health assurance.
  

Interface schematic

Product Information & Parameters

• Product name: TWS Bluetooth Headset with vacuum water Cup.

• Capacity: 500ml.

• Stainless steel grade: 06Cr19Ni10(SUS304).

• Plastic parts: food grade silicone.

• Bluetooth version: V5.0.

• Executive standard: GB/T 29606-2013《stainless steel vacuum cup》.

• Insulation performance: Fill the cap with water above 70°C after
  6 hours≥40°C.

• Power interface: Micro USB.

• Support over-current, over-voltage, short circuit, over-temperature protection.

• Input voltage: charging box DC 5V 0.5A; headphone DC 5V 50mA.

• Charging time: charging box about 60min; earphone about 40min

• Built-in battery  in the charging Box: polymer lithium battery 300mAh (full charge needs around 60 min, charging the pair earphones about 3 times, charging single earphone around 6 times).

• Headphone battery: polymer lithium battery 30mAh; use time is around 2-3 hours

Instruction for Earphones Function

• Boot
  Take the headset out of the charging compartment and automatically turn it on or press and hold the left and right headset multifunction touch button for 3 seconds

• Shut down
  Put the headset into the charging compartment and turn it off automatically.Press and hold the left and right headset multifunction touch button for 5 seconds to shut down.

• Boot back
  When the pairing is successful,the bluetooth headset preferentially enters the connected state when the second time is turned on,and automatically connects back to the connected mobile phone.

• Play/pause
  In the standby mode,double click the left and right earphones multi-function touch keys to play music directly.When playing, double click the left and right earphones multi-function touch keys to pause playback.

• Volume adjustment
  Click the left ear function button volume “+”; click the right ear function button volume “-“.

• Switch songs
  three clicks on the left ear function button is “previous song”; three clicks on the right ear function button is the next song.

• Call answering
  When the mobile phone calls,click the left and right earphones multifunction touch button to answer the call.

• Call hang up
  When the phone is talking ,click the left and right earphones multi-fuction touch button to hang up the phone.

• Call rejection
  When the mobile phone calls,long press the left and right headphones multi- function touch button for 2 seconds to reject the call.

• Redial
  While on standby or playing music, you can dial the last call you made in your call history by tapping the left headset multifuction touch button.

• Low battery prompt
  When the battery of the bluetooth headset is low,the low battery tone will be played every 30 seconds untill the headset is powered off.

Instruction of Pairing Method of Earphones

• Bluetooth name: E5
• Make the earphones power on by taking them out from the charging box or long pressing the multifunction touch button of left and right earphone at the same time for 3 seconds. Warning tone “power on” and the blue light and red light flash alternatively, at the same time, earphones enter searching and paring status. Warning note “Pairing” means entering automatic paring of two earphones. After paired successfully, the main earphone flashes alternatively with red and blue light,the sub earphone flashes with slow blue light, at the same time, playing warning tone “connected”
• Enable Bluetooth on your phone or other device. For Android, please click “search Bluetooth device” on your phone. For IOS mobile phones or devices, it would automatically search for devices; After searching Bluetooth name “E1”, click it to enter pairing; When the pairing is successful, the main earphone would play tone” connected” which means the connection is successful and the lights in the left and right earphones would all go out.
• The two earphones can also be paired with the phone separately. Same operation method as two steps as above. seconds.

Instruction of Charging

• Plug one end of the Micro USB charging cable into the USB port of the charging box, and the other end to the adapter charge the charging box. When the battery level of the charging box is within the indicator range of the corresponding indicator light, the red indicator light at that position flashes once every 2 and the red light will be long on when it is fully charged.
• Charge the earphone: put the earphone into the charging box to charge it automatically. The earphone indicator is red when charging, and it will be off when fully charged. The blue indicator light of the charging box is long on, and the blue indicator light of the charging box is off when the earphones are fully charged. Blue light flashing when low power alarm.

Attention

• Do not wash the inside of the charging box during use. The surface of the charging box can only be quickly washed with a small amount of water or wiped with a wet towel.
• Minors should be used under the guidance of an adult.
• Wash the cup with warm detergent in warm water before use.
• In order to achieve the best cold preservation effect, it is recommended to add hot water or ice first to be preheated or pre-cooled.
• When adding boiling water to the cup, it should not be too full and there is a danger of spilling and scalding.
• Tighten the lid clockwise when the cup is tilted. To prevent leakage.
• Avoid falling, bumping or strong impact, which will cause deformation of the cup and affect the product use efficacy.
• Avoid any form of direct heating or place at high temperatures. It is strictly forbidden to place the product in Heating in open flames, induction cookers, microwave ovens, and dishwashers.
• Do not add dry ice, carbonated drinks, etc., which are prone to high pressure,do not add soy sauce, soup and other liquids containing alkaline and acidic ingredients to avoid cup corrosion.
• After loading a perishable beverage such as milk, please drink it as soon as possible and wash it to avoid the liner decay. Do not use it for other purposes except heat preservation and cold preservation.
• When not in use for a long time, clean it and keep it dry.
• Please charge in a safe environment. When charging the charging box, please pull out the charging cable as soon as possible after the charging indicator indicates full charge, so as to avoid damage to the charging box caused by long time of charging.
• When playing music, please turn the music to the appropriate volume to avoid damage to the hearing under the condition of long-term high volume.
• Try to avoid using this earphone where there is interference source, otherwise it may affect the earphone signal.
• Try to avoid using the earphone in a corrosive environment, so as not to affect the function of the earphone.

Tips: when you use it for the first time, please connect the attached data cable to the power adapter to charge for half an hour to achieve the best effect of the built-in battery. When using the Bluetooth Earphones to listen to music or talk, please pay attention to adjust the volume, so as not to affect your listening!

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.The
  device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>