Klipsch Jubilee Floorstanding Speaker Owner’s Manual
- October 30, 2023
- Klipsch
Table of Contents
Jubilee Floor standing Speaker
Owner’s Manual
UNPACKING AND ASSEMBLY
CONNECTING HIGH FREQUENCY HORN TO LOW FREQUENCY CABINET
PLACEMENT
Your Klipsch Jubilee loudspeakers will perform well in a variety of locations, but for best results use the following guidelines:
- Place on a common wall that is 12 to 15 feet away from the main listening position.
- Position them equidistant from the wall behind the speakers, as well as equidistant from the main listening position, creating an equilateral triangle.
- Angle speakers toward the listener and even with or forward of any adjacent obstructions.
- Placing them near a corner or wall provides the greatest amount of bass while moving the speakers away from room boundaries reduces bass energy.
- Asymmetrical placement of a pair of speakers from adjacent side walls can smooth room-induced bass unevenness.
Experiment with the above guidelines to suit your taste and to compensate for your room’s acoustic characteristics.
ACTIVE CROSSOVER
*Power LED will blink yellow anytime clipping/overdriving is occurring.
**When using an unbalanced (RCA) connection, if your preamp signal is causing
consistent clipping, set the pad switch to -9 dB to compensate.
POWER ON / OFF| POWER LED / CLIPPING INDICATOR| LOW FREQUENCY (LF) GAIN| HIGH
FREQUENCY (HF) GAIN
---|---|---|---
POWER INPUT| ALWAY ON / AUTO ON SWITCH| INPUT TYPE BAL/UNBAL
PASSIVE ATTENUATION 0 dB/- 9 dB PAD| PRE-AMP INPUT (R+L) BALANCED| PRE-AMP
INPUT (L+R) UNBALANCED| AMPLIFIER OUTPUTS
POWER LED COLOR CODES
| WHITE (Blinking) | Powering On |
|---|---|
| WHITE | Power On |
| YELLOW | Clipping |
| RED | Standby* |
| OFF | Power Off |
*Please Note that the crossover will only remain in Standby for approximately 15-25 seconds. The unit will power off after this period.
ACTIVE CROSSOVER (INPUT)
| PRE-AMP (EXAMPLE) | XLR (NOT INCLUDED) | RCA (NOT INCLUDED) |
|---|
If using an XLR connection, set the “INPUT TYPE” switch to “BAL”
If using an RCA connection, set the “INPUT TYPE” switch to “UNBAL”
*When using an unbalanced (RCA) connection, if your preamp signal is causing consistent clipping, set the pad switch to -9 dB to compensate.
Please Note that the EQ/DSP on the crossover is active whether using Balanced
or Unbalanced connections.
ACTIVE CROSSOVER (OUTPUT)
| 2 CHANNEL AMPLIFIER (EXAMPLE) | AMPLIFIER OUTPUTS |
|---|
If your setup requires it, you can also mix and match RCA/XLR connections. For
example, you can use XLR connections for the HF, and then use RCA connections
for the LF, or vice versa.
THIS SPEAKER IS ONLY ABLE TO BE CONNECTED VIA A BI-AMP SETUP. DUE TO THIS, YOU
WILL NEED AN AMPLIFIER WITH AT LEAST 4 CHANNELS OF POWER, OR 2 SEPARATE
AMPLIFIERS WITH AT LEAST 2 CHANNELS ON EACH.
CONNECTIONS (TWO 2 CHANNEL AMPLIFIERS)
2 CHANNEL AMPLIFIER (EXAMPLE)
CONNECTIONS (4+ CHANNEL AMPLIFIER)
4 CHANNEL AMPLIFIER (EXAMPLE)
IMPORTANT SAFETY INSTRUCTIONS
- READ these instructions.
- KEEP these instructions.
- HEED all warnings.
- FOLLOW all instructions.
- DO NOT use this apparatus near water.
- CLEAN ONLY with dry cloth.
- DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- ONLY USE attachments/accessories specified by the manufacturer.
- USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
- REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
** This symbol indicates that there are important operating and maintenance
instructions in the literature accompanying this unit.
WARNING: To reduce the risk of fire or electrical shock, do not expose
this apparatus to rain or moisture.
WARNING: No user-serviceable parts inside. Refer all servicing to
qualified service personnel.
INSPECTION
We want your new speaker system to look as good as it did leaving the factory!
Please check promptly for any transit damage. Carefully unpack your new
speaker system and verify the components against the packing list. In extreme
circumstances, items may have become damaged in transit. If any damage is
discovered, notify the delivery service and dealer where the system was
purchased. Make a request for inspection, and follow their instructions for
evaluation. Be sure to keep the product’s original shipping carton.
ABOUT YOUR KLIPSCH PURCHASE**
Thank you for your purchase of Klipsch Heritage loudspeakers. After reading
this manual and connecting your system, you will hear the result of over 70
years of stringent engineering and class-leading research and development.
Like all Klipsch products, your loudspeakers feature Klipsch Horn-loaded
Technology—the guiding design for the first Klipschorn® developed in 1946 and
for every Klipsch product that has followed. Horn-loading allows your speakers
to deliver very high sensitivity, wide dynamic range, low distortion,
controlled dispersion and flat frequency response. This translates to
unequaled power, detail and dynamics, the hallmarks of “The Klipsch Sound.”
Again, thank you for choosing Klipsch and we hope that your speakers bring
life to your music and movies for many years.
KEEPERS OF THE SOUND
3502 WOODVIEW TRACE, INDIANAPOLIS, IN, USA
KLIPSCH.COM
©2022 KLIPSCH GROUP, INC ALL RIGHTS RESERVED. KLIPSCH KEEPERS OF THE SOUND,
KLIPSCHORN ARE REGISTERED TRADEMARKS
OF KLIPSCH GROUP, INC. THE USA AND OTHER COUNTRIES. A WHOLLY-OWNED SUBSIDIARY
OF VOXX INTERNATIONAL CORPORATION.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>