JBC AP250 Manual Feed Soldering Iron Instruction Manual
- June 5, 2024
- JBC
Table of Contents
- JBC AP250 Manual Feed Soldering Iron
- Packing List
- Features and Connections
- Changing Cartridges
- Solder Wire Replacement
- Changing the Feeder Nozzle
- Regulating the Feeder Nozzle
- Compatible Cartridges*
- Accessories
- Specifications
- Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
JBC AP250 Manual Feed Soldering Iron
This manual corresponds to the following references: AP250-A
Packing List
The following items are included:
Features and Connections
AP250 works with DIU, DDU, DMU Control Units by using APS Stand or optional with CDA Manual-Feed Soldering Station.
Changing Cartridges
For a safe cartridge change, unplug the tool or turn the station off before following these guidelines
- Loosen the screw and remove the cartridge. Use JBCs PLR195 catridges extractor pliers to remove it if still hot.
- Important: Insert the cartridge as far as the mark for a correct connection.
- Align the tip of the cartridge with the feede nozzle. Use JBCs PLR195 catridge extractor pliers for a correct tip alignment.
- Important: Tighten the screw again. This i necessary for the tool to function.
Solder Wire Replacement
- Pull out the remaining solder wire from inside the feeder nozzle. Use a pliers if necessary.
- Remove the empty reel as shown and fit the new one in the same direction.
- Insert the solder wire while pushing the trigger repeatedly until the solder wire appears at the nozzle.
Note: Use solder wire ø0.8 – 1.0 mm with Nozzle Ref. 0019212 and ø1.1 – 1.5 mm with Ref. 0019211
Changing the Feeder Nozzle
Make sure the tool is unplugged.
- Open and take out the back side screw to remove the reel and to take out the solder wire from the nozzle.
- Then remove the two front side screws and lift the cover off
- Take out the feeder nozzle and replace it with the new one while holding the following 3 components inplace Reassemble the handpiece and tighten the 3 screws.
Note: Do not disassemble these 3 components and it is imperative to hold them in its place.
Regulating the Feeder Nozzle
Depending on the component are soldered or the cartridge being used, the length of the feeder nozzle can be either shorten or lengthen (max 10 mm / 0.394 in).
- Loosen the screw to change the length of the feeder nozzle.
- Adjust the feeder nozzle length to the required length (max 10 mm / 0.394 in) and tighten the screw.
Compatible Cartridges*
AP250 Solder Feed works with C250 cartridges. Find the model that best suits your soldering needs in www.jbctools.com
Accessories
**Solder Reel Stand***
For production line work, BES Solder Reel Stand is the ideal solution for easy
solder wire supply. Suitable for Solder Reels up to 2.5 kg / 5.512 lb.
Wrap the solder wire twice around the empty reel as shown.
**Fume Extractor***
The fume extractor is an easy & safe solution extract the fume generated at
the solder joint while soldering.
Note: Suction pump and filter required.
Specifications
AP250
Manual-Feed Soldering Iron Ref. AP250-A
- Solder Wire Diameter: Up to 1.5 mm / 0.06 in
- Total Net Weight: 232 g / 0.51 lb
- Package Dimensions / Weight: 245 x 185 x 45 mm / 367 g (L x W x H) 9.65 x 7.28 x 1.77 in / 0.81 lb
- Complies with CE standards ESD safe
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at
the end of their life must be collected and returned to an authorized
recycling facility.
Manual in other languages available on our website www.jbctools.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>