Tie TBT1 Mobile Bluetooth Transmitter or Receiver User Manual

Tie TBT1 Mobile Bluetooth Transmitter or Receiver User Manual

OVERVIEW

1. LED indicator
2. Multifunction button (MFB)
3. Micro USB charging jack
4. 3.5mm audio port
5. Secure clip
6. RX / TX switch button

INTRODUCTION

The TBT1 is a 2-in-1 Bluetooth stereo audio adapter that allows you to switch between receive and transmit modes. You can easily access your audio devices and send or receive stereo audio wirelessly via Bluetooth. No additional software installation is required.

CHARGING THE TBT1

We strongly recommend that you fully charge the adapter before using it for the first time. It takes about 3 hours to fully charge the adapter for the first time.

1. Charge with computer: connect the micro USB cable to the adapter power connector and the standard USB plug to computers USB port.
2. Using an electrical outlet to charge: connect the micro USB cable to the adapter and the standard USB plug to a DC 5V adapter.
3. Indicator status:
4. RED = charging
5. OFF = charge completed

Note:

1. When the battery of the adapter is almost empty, the LED flashes red and a beep sounds. Please charge the adapter.
2. If you have not used the adapter for a few months, the LED may not turn red at first when charging. It may take 15-35 minutes for the LED to turn red. We recommend fully charging the adapter at least once every two months.

RECEIVER (RX MODE), SWITCH ON / OFF

Please set the TX/RX switch to the RX position before starting the TBT1. The TX or RX mode can no longer be changed during operation.

Switch on: Press and hold the MFB key for approx. 2 seconds until the LED flashes blue. Beeps will sound during this process.

Switching off: Press and hold the MFB key for approx. 3 seconds until the LED flashes red and then goes out. Beeps sound when you do this.

RECEIVER

Pairing with a smartphone

1. Ensure the receiver is turned off.
2. The TBT1 and your smartphone should not be more than 1 meter apart.
3. Press and hold the MFB button for about 6 seconds until the LED flashes in red and blue alternatively and fast. The Bluetooth adapter enters into pairing mode.
4. Activate the Bluetooth function and search the adapter within your smartphone.
5. Select „ TBT1“ from the device list, follow the steps and enter pass code 0000 if requested to pair.
6. Connect the TBT1 with your smartphone.
7. After the successful pairing, the LED will flash blue three times every 2 seconds.

Note:

1. Please make sure your smartphone’s Bluetooth function is activated before pairing.
2. The pairing mode will last for 2 minutes.
3. Once turned on, the TBT1 will search and connect automatically with the last paired device in working range.
4. The TBT1 will automatically switch off if no device can be connected within 5 minutes.
5. Clear the pairing list: Turn the TBT1 off, then press and hold the MFB button for about 12 seconds until the LED flashes red for 1 second and then flashes in blue for 1 second. Afterwards, the receiver enters into pairing mode automatically.

STREAM MUSIC

1. After successful pairing, connect the Bluetooth receiver to a pair of 3.5mm stereo headphones or a wired speaker using the included 3.5mm audio cable. Now you can enjoy your favorite music from your smartphone or other media players.
2. Press the MFB button once to pause or play the music.
3. The LED keeps blue when music playing.
4. In standby mode, the LED flashes in blue once every 1 second.

TRANSMITTER (TX MODE), SWITCH ON / OFF

Please turn the TX/RX switch to TX position before getting started. TX or RX mode can no longer be changed during operation.

Switch on: Press and hold the MFB button for about 2 seconds until the LED flashes blue.

Switching off: Press and hold the MFB button for about 2 seconds until the LED flashes red and then goes out.

TRANSMITTER, PAIRING WITH A BLUETOOTH DEVICE

After connecting the transmitter to a Bluetooth stereo device, you can enjoy music without wire restriction.
Before pairing, please make sure that your Bluetooth device supports the Bluetooth profile A2DP.

Pairing procedure

1. Please make sure the transmitter is turned off.
2. Keep the transmitter TBT1 and your Bluetooth headphone within 1 meter.
3. Press and hold the MFB key for approx. 4 seconds until the LED flashes blue quickly. The Bluetooth transmitter then enters into pairing mode.
4. Set your Bluetooth headphone into pairing mode.
5. The transmitter TBT1 will automatically search, pair and connect with your Bluetooth headphone.
6. After successful pairing, the LED flashes blue twice every 2 seconds. Now you can connect the transmitter TBT1 to your TV, computer or music player via the included 3.5mm audio cable to enjoy your stereo music wirelessly

Note:

1. The pairing mode will only last for 2 minutes.
2. Once turned on, the transmitter TBT1 will connect automatically with the last-paired device.
3. The transmitter will automatically switch off if no devices can be connected within 10 minutes.
4. LED indicator instruction
   • In standby mode: flashes blue once every 1 second
   • In pairing mode: flashes blue quickly
   • Connecting mode: flashes blue twice every 2 seconds
5. Clear the pairing list: turn the Bluetooth transmitter TBT1 off, then press and hold the MFB button for about 12 seconds until the LED flashes red for 1 second and then flashes blue for 1 second. Afterwards, the transmitter enters into pairing mode automatically

SAFETY INFORMATION

• The battery used in this device may cause a fire or present a chemical explosion hazard if mishandled.
• To avoid damage or malfunction of the device, do not drop the device from great high places.
• Keep the device away from humidity, water and any other liquid. If the device is exposed to water, moisture and other liquids, do not operate it to avoid any electrical shock, explosion and damage to the device or yourself.
• Do not place or keep the device near any heat source, such as direct sun light, radiators, stoves or other apparatus which produces heat. It may cause explosion, degrade the performance or reduce battery life.
• Do not modify, repair or disassemble the device at discretion (especially battery, it may cause an explosion). Doing this will avoid the warranty.
• Do not place heavy objects on the device.
• Use the supplied and approved charger only.
• Service must be performed by a qualified service center or the manufacturer.
• Unplug the unit from the wall outlet when unused for long periods of time and during lightning storms.

TECHNICAL SPECIFICATIONS

Bluetooth version CSR 4.1 with aptX low latency
Bluetooth profile A2DP and AVRCP
Working range 10m
TX mode working time 9 hours
RX mode working time 8 hours
Standby time up to 200 hours
Charging time about 3 hours
Charging input voltage DC 5V
Battery 260mAh rechargeable Li-polymer battery
Dimensions 38 × 39 × 15mm
Net Weight 19g

Work and standby times may vary when used with different cell phones or other compatible Bluetooth devices, usage settings, usage types, and environments. Specifications are subject to change and improvement without notice.

CONTENTS

• 1× Bluetooth Transceiver
• 1× Micro USB Cable
• 1× 3.5mm Audio Cable
• 1× Quick Start Guide

www.tie-products.com

Brand: TIE® is a registrated trademark of sonic sales GmbH.
General Importeur worldwide: sonic sales GmbH, Liebigstraße 24, 33803 Steinhagen, Germany
Electronic waste: This product underlies the guidelines of WEEE authority.
Declaration of conformity: This product has been approved for getting the CE and FCC symbol.
Articlenumber: The article TBT1 is specified by the articlenumber: 19-90057
After sales support: support@tie-products.com
Designed and engineered in Germany. Made in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>