FALCON RIDGE PO-10CREW-WTC01 Full Size Polaris Ranger Crew Soft Windshield & Top Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
10CREW-WTC01 Full-Size Polaris Ranger Crew Soft Windshield & Top
Instruction Manual
PO-10CREW-WTC01 Full Size Polaris Ranger Crew Soft Windshield & Top
Instructions for Installation and Care of Polaris 10 Ranger Crew
Windshield/Top ComboPO-10CREW-WTC01
Notice: Do not smoke inside the cab or expose the enclosure to direct
flames. The cab is Flammable.
-
Be sure to read these instructions thoroughly before opening and installing the Polaris Ranger Cab Enclosure. The installation is best done when the temperature is 70 degrees F. or warmer. This is to allow the Velcro to stick to the roll cage better, if you must install it outside in the cold it will help to warm the Velcro inside at room temp. until ready to install.
-
Carefully open the carton and remove the rolled Cab Enclosure on a large flat surface that is clean and free of dirt or other material that may soil or scratch the windows of the Cab
-
It will help to unhook the hood prior to installing the cab enclosure
-
Check over the parts included in the carton with the parts list shown below:
Velcro Hook strips:| 2 eac| 4” long
---|---|---
“ “| 4 each| 10” long
“ “| 4 each| 6” long
Cab Enclosure| 1 eac| -
Loosely drape the Cab Enclosure over the Ranger roll cage. Next, take the three straps on the nose and attach them to the front of the Ranger. The middle strap is longer and will go down and wrap around the bar that is in the hole along the bottom portion of the bumper. The two side straps wrap around the top bumper bar on each side. If you have a winch, it may interfere with the center strap, in this case, you may not use it, the side straps are enough to hold the nose. The photo below will help show you where to place the straps.
-
Now pull the straps tight so that the edge of the nose lines up with the top of the front panel that has Polaris embossed in it. This is to ensure that the cab is in its proper location from front to back. Once this is done you will now loosen these straps and leave it be until the final step.
-
Working your way to the rear of the roll cage, pull the rear corners down to determine the correct positions to place the 6” adhesive Velcro strips around the roll bars. The photos below show the correct way to attach the double-sided Velcro.
-
Note the position and install two 10” and one 4” hook and loop strips on the left side of the roll cage for the front window. Be certain to clean the surfaces before applying the adhesive hook strips! Attach these Velcro strips and pull the windshield tight to the sides and affix the Velcro tabs to the adhesive strips. Now retighten the straps on the front of the nose and you are finished, Enjoy!
Cleaning and Storage Recommendations:
-
Before removing the Falcon Ridge Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll it for storage.
-
It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when
it was packed at the factory On a large, clean and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at normal room temperature. It is best not to expose the Cab to either extremely hot or cold temperatures when storing. -
A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if the additional hook and loop sets are needed, they can also be ordered.
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from the date item is received. You MUST package the product exactly
as it was originally packaged from the factory to get a full refund for the
product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory-new condition to receive a refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridges’s many distributors, you must first call them and
see what their return policy is. Once your item reaches our production
facility, our customer satisfaction team will inspect your item to ensure
unused, factory-new condition. NOTE: All windshields must be returned with the
original protective film intact and not removed. Do NOT REMOVE if you have any
intentions of returning the item. Refund/ replacement of a windshield will
only be processed on items with original protective film or if the windshield
is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered or damaged in any way will not be subject to a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, a credit will be issued to the
original credit card/ payment method used for the purchase. Outbound shipping
and return shipping costs will not be refunded. Please allow 4 to 6 weeks for
your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty. 30 Day Warranty which includes and is not limited to
replacing the enclosure, tops, and/or windshield due to defects of the
product. Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase.
Thank you,
Falcon Ridge
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>