CTE TECH CN6209 Motorcycle Dashboard Instructions

CN6209 Instruction of Motorcycle Dashboard
Product name：Motorcycle Dashboard (with Bluetooth & WIFI functions)
Brand：CTE TECH CORP.
Model name： 7in
Serial number：CN6209
Manufacturer：CTE TECH CORP.
No.1-7, Gongjian Rd., Cidu District,
Keelung 20647, Taiwan, R.O.C
Telephone number：+886-2-2452-2431
Fax number：+886-2-2451-5384

Product description：

Vehicle device for large-sized motorcycle and provides a status of vehicle.
This motorcycle dashboard can display such as vehicle speed, fuel quantity, total mileage, short mileage, battery voltage, indicator light, time, gear position, remaining mileage, average speed, average fuel efficiency, time functions, etc.

Specification：

System specification

Description

| ****

Content

Size of main body| 19211743 mm
Wired connection interface| 20pin connection interface
Wireless connection interface| Ø   Bluetooth (BLE 5.0)
Ø   Bluetooth (BT 5.0)
Ø   WiFi (WiFi 4.0)
RF Power| Ø   BLE：Programmable RF transmit power from -19 to +2.2 dBm
Ø   BT：Maximum RF Transmit Power 13.5 dBm
Ø   WIFI：Tx Power：+19 dBm Rx Sensitivity：-98.5 dBm
Frequency Range| Ø   BLE：2402~2480MHz
Ø   BT：2402~2480MHz
Ø   WIFI：2412~2484MHz
Outer case material| AES+PMMA
Weight| 520g
Operating Voltage| DC 8V~18V
Operating Current| 200mA~2000mA
Quiescent Current (Key OFF)| 0.2mA
Operating temperature| -30~+80℃
**** Storage temperature| -40~+90℃

Motorcycle dashboard screen is displayed as follows.

Input/output interface characteristics：

PIN| Description| Input /Output| Electrical characteristics
---|---|---|---
1| CAN_H| Input /Output| CAN_H
2| CAN_L| Input /Output| CAN_L
3| USB_5V| Input| USB_5V
4| USB_DN| Input| USB_DN
5| USB_DP| Input| USB_DP
6| USB_ID| Input| USB_ID
7| GND| | GND
8| ABS_12V| Output| Output 12V
9| AUX1_5V| Output| Output 5V
10| | |
11| | |
12| | |
13| BLE_UPDATE| Input| BLE_UPDATE
14| | |
15| | |
16| | |
17| BAT| Input| Battery power
18| IGN| Input| Key ON/OFF 13V, High will be ON, Low will be OFF
19| GND| | GND
20| AUX2_5V| Output| Output 5V

Bluetooth connection：

Step 1.
Go to mobile phone’s settings page→ select Bluetooth function → turn on Bluetooth function → find available devices → select QCC5181 for pairing.

Step 2.
“Pairing code 011012 Confirm pairing code?” will be displayed on motorcycle dashboard.
Note: The Pairing code will be produced a different new 6-code every time when the motorcycle dashboard needs to pair a new device.

Step 3.
The mobile phone screen will display the pairing request with the Bluetooth QCC5181, the password key 011012, which is the same as the pairing code 011012 displayed on the motrocycle dashboard, and then press OK.
Bluetooth connection established.
Note: The password key will be showed the new 6 random codes everytime when the motrocycle dashboard needs to pair a new device.

WIFI connection：

Step 1.
Go to mobile phone’s settings page→ select connections→  turn on WIFI function.

Step 2.
Find available devices → select LXP WLAN for pairing.

Step 3.
Key the WIFI passward key 619898, the WIFI connection established.

E-Label display

Step 1.
At main page long press handle’s “OK” button to enter Info, update and reset page.

Step 2.
At Info, update and reset page, short press handle’s “OK” button to enter Certifications page.

Step 3.
At Certifications page short press handle’s “OK” button and then the E-Label will be shown.

Label

Physical printing label

WARNING

FCC Statement:
(Section 15.105)
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

(Section 15.21)
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
IC Statement:
Canada, Industry Canada (IC) Notices
This device complies with Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cauinterference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Innovation, Science and Economic Development Canada radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure
limits under mobile exposure conditions. (Antennas are greater than 20cm from a person’s body).
NCC Statement
Taiwan regulatory information(NCC)：
KCC Statement:
EMC (KN 32/35) Class A device only
ANATEL Statement:
“Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados” (se aplicável);
“Para mais informações, consulte o site da Anatel: https://www.gov.br/anatel /pt-br “

References

• Anatel — Agência Nacional de Telecomunicações

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>