Zhuhai Quin Technology M120 Portable Label Printer User Manual

M120 Portable Label Printer
User Manual

Please read this instruction carefully before using this product and keep it properly

Packaging List

1. Priter*1
2. Product Instruction*1
3. Data cable*1
4. Adjustable plate*1

Device parameters

Micro USB
Battery| 1500mAh
Product Size| 4.3×3.3×2.3in
Power Input| 5V⎓ 2A
Power Supply Method| Micro USB
Lithium battery
Operatinng Information| Supported operating system| Windows7/8/10
Android
ios
Instruction set| ESC/POS/TEPL
Bar code| 1D bar code&2D bar code
Operating temperature| 5°C-50°C
Storage temperature| -20°C-60°C
| Operating humidity| 20%-85%
---|---|---
Storage humidity| 5%–95%(Noncondensation)

Component instruction

• Paper Exit
• Screen
• Power Button
• Feed Button
• USB USB
• Reset Hole
• Rope Hole
• Turn On /off

1. Press the Power Button for 2 seconds to turn on the printer.
2. To turn it off, please press the Power Button for 2 seconds .

Feed :

1. Label paper /Black mark label: Press Feed Button to feed the tape to the proper place and get ready for printing the next tape.
2. Continuous paper: Press Feed Button to keep paper feeding .it will stop when you let go of the button.

System Setting :

1. Press the Power Button for 1 second to switch to the setting interface.
2. Press Feed Button for 1 second , scroll option list, and select, by pressing Power Button
3. Press Power Button for 2 seconds to go back to the main page.

Installing the Paper Roll

1. Hold the printer and lift the paper cover
2. Take out the adjustable plate and remove the left panel
3. Put the paper roll ( The print site should be below) and push it to the right(Dividing ruler should be above Note the position of the paper roll device as shown)
4. Aim the adjustable plate at both slots and slowly put into the paper bin .
5. Press the Power button for 2 sec to turn on the paper bin by approximately15mm ) and close the paper cover make sure the paper bin is closed.
6. Press the Power button for 2 sec to turn on the printer,press feed button to push the one-piece plate. Connect to the App, and start to use it .

Search Print master on App Store or Google Play to Get the App
Screen Information

• Bluetooth
• Setting /Transfer
• Cover Opening
• Paper Condition
• Print Condition
• External Electricity
• Charging Battery
• Logo area
• Text area
• Logo guidance
• Bluetooth

When the printer connects to Bluetooth, this logo will light up . This logo will flash when the data is transferred. Setting /Transfer When you are using a USB wire, this logo will be shown as; If you press the Power Button for a short time, it will be switched to Setting Mode, and the logo will be shown as Setting Mode.

Cover Opening
It indicates that the paper cover is opened or not closed correctly. A message will appear, stating that the paper cover is opened .
Paper Condition
If the paper roll is not installed correctly, or there is insufficient paper, this logo will light up. A message will appear, stating that there is no paper . When the paper is detected it will give you a confirmation so that you are able to proceed.
Print Condition
It will light up while the printer is printing or feeding
External Electricity
It will light up when the printer is connected to a power source.
Charging Battery
Please charge your printer when the power display begins to flash.
Text Area
This area shows related text information

Screen setting

1(Lightest),2,3,4(Light),5,6(Normal),7,8,,9,10(Thick).111213,14,15(Thic kest )
Print speed| 1(Slowest),2(Slow).3(Normal),4(Fast),5 (Fastest)
Paper type| Interstitial paper, continuous paperback mark label
Automatic shutdown| 5min .15min .30min .1h .2h ,4h .8h .24h .No shutdown
Restore settings| Press the power button to restore
Firmware version| Display Firmware version
Device address| Display device address

Screen hint

Product warranty

“Thank you for choosing the Portable label printer The free warranty period of this product is one year from the date of purchase (subject to the date of the official purchase invoice). Within 30 days from the next day of the user signing for receipt, the user ay chooses to return, replace the goods or enjoy the free maintenance service. Please keep the warranty card properly, which will not be reissued in case of loss.

Non-warranty Regulations
The warranty is void under the following conditions·
Exceeding the warranty period.
Not presenting the original warranty/maintenance card Presenting a damaged warranty /maintenance card ( e.g.tearing or tampering ).
Damage caused by unauthorized repair, disassembling, etc.
Damage caused by human error.
Damage caused by natural disasters such as earthquakes kes , floods, windstorms, lightning strikes or external disasters such as fires and house collapses.
Failure o damage caused by harsh conditions (oil, moisture, direct sunlight, etc .)or failure to use or care for as outlined by the instruction manual.

FCC Caution
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide easonable protection against harmful interference in a residential installation . This equipment generates uses and can radiate radio frequency energy and if not installed and sed n accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver .
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio /tv technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation.

Request
Warranty /MaintenanceCard

• Replace
• Return
• Repair

User Information

Name :
Gender
Phone :
Address :
Product Information
Date of purchase :
Product order number :
Product serial number :| Reason foreturn(Replace/Repair/Request  alntenance )
Fault description :
Maintenance Records :
Fault conditions :
Maintenance staff
Processing situation :
Repair date
Repair ticket number :
Date of inspection :
---|---

FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device ust accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed nd used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

*RF warning for Portable devices:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>