SERCOMM OC1101 Industrial LTE CPE User Manual

June 5, 2024
Sercomm

Industrial LTE CPE
User Manual  

V1.3.6
July 2, 2020

Before Use

Steps:

  1. Remove bottom cover
  2. Insert Micro SIM card into carsocket(yellow frame)
  3. Connect power cable and LAN cable
  • Please wear anti-static gloves and always remove/insert micro SIM card when the device is power off.

Configure Laptop/PC Ethernet to Fixed IP

To connect to the video bridge, please use fixed IP all the time no matter in configuration or assigned IP check period.

Steps:

  1. Configure Laptop IP to 10.10.2.10/255.255.255.0 (Don’t use DHCP to get IP from CPE)
  2. Click “OK”

How to Login GUI

SERCOMM OC1101 Industrial LTE CPE - Fig 9

Steps:

  1. Visit https://10.10.2.254
  2. User ID/PW: admin/admin
  3. Click “Sing In”

How to Get LTE information

SERCOMM OC1101 Industrial LTE CPE - Fig 10

Steps:

  1. Visit https://10.10.2.254
  2. Click “Status” on the left menu

How to configure APN Name-NAT

SERCOMM OC1101 Industrial LTE CPE - Fig 3

Steps:

  1. Visit https://10.10.2.254
  2. Click “Setting” on the left menu
  3. Configure APN Name if required
  4. Click ”Save”
  5. Click “Restart “ or unplug to reboot the device

How to configure APN Name-Bridge

SERCOMM OC1101 Industrial LTE CPE - Fig 4

Steps:

  1. Visit https://10.10.2.254
  2. Click “Setting” on the left menu
  3. Tick the checkbox of Bridge and configure APN Name if required
  4. Click ”Save”
  5. Click “Restart “ or unplug to reboot the device
  6. Configure laptop/PC ethernet to DHCP to get IP in bridge mode.
  7. Configure laptop/PC ethernet to fixed IP when need to enter GUI in bridge mode.

How to Upgrade Firmware

SERCOMM OC1101 Industrial LTE CPE - Fig 5

Steps:

  1. Visit https://10.10.2.254
  2. Click “Administration” on the left menu
  3. Click “Choose File” to choose the firmware file
  4. Click ”Upload”

How to Reset to Default

SERCOMM OC1101 Industrial LTE CPE - Fig 6

Steps:

  1. Visit https://10.10.2.254
  2. Click “Administration” on the left menu
  3. Click “Config File”
  4. Click “Factory Defaults” to reset to default settings
  5. Click “Restart “ or unplug to reboot the device

How to Read LEDs

STATUS STATUS LED LTE SIGNAL LED
Green Off Off

Off
Power On
Power Off| Off| Off| Off| Off| Off
No SIM card| Off| | Off| Off| Off
FW Upgrading| r3link| Off| Off| Off| Off
FW Upgrading Fail| On| | Off| Off| Off
PLMN Search / Network Attaching| I On| Off| Off| | Off
RSRP (> -87) dBm| On| Off| | Off| Off
RSRP ( -106 – -87) dBm|  On| Off| Off| | Off
RSRP (<-106) dBm| On| Off| Off| Off| On

How to Mount the Device_Pole Mount

SERCOMM OC1101 Industrial LTE CPE - Fig 7

How to Mount the Device_Wall Mount

SERCOMM OC1101 Industrial LTE CPE - Fig 8

Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and sed in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be  determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals