national2way WPTT-PDNT-IOS Wireless PTT Pendant User Manual

User’s Manual – Wireless PTT Pendant
Model: WPTT-PDT-IOS
Wireless PTT Pendant for WAVE with 3.5mm
Female Connector and Power Cord
FCC ID: 2A2BD-WPTT-PDT-IOS

Product Overview:

Package contents:

• Wireless PTT Pendant
• Magnetic charging cable
• User’s Manual

Operation:

• Power ON: Press the power ON/OFF button and hold for 3 seconds until the “Power on” sound is heard by the earphone; the status LED flashes purple once to indicate the device is turned on.
• Power OFF: Press the power ON/OFF button, and hold for 3 seconds until the “Power off” sound is heard by earphones; the status LED flashes purple once to indicate the device is turned off.
• PTT Button: Press and hold down this button to talk, release to end transmission.
• Volume control: Press volume up (+) / down (-) button to adjust volume. The device will produce a tone when the volume reaches the minimum or maximum level.
• External earphone: Open external earphone jack dust cover, plug listen-only earphone with Ø3.5 2pole or 3pole connector.

Status LED:

How to Pair Process for radio/phone / WAVE OnCloud

1. Make sure Wireless PTT Pendant is OFF, press & hold the power button to switch it on.
2. Wireless PTT Pendant is under pairing mode when the LED flashes Red and Blue alternatively and the “Pairing” sound is heard by the external earphone.
3. Start the Bluetooth function on your radio/phone.
4. Find the device name “2Way Audio” under the Bluetooth device list and connect it.
5. The pairing process is completed, and the “Paired” sound is heard by the external earphone.
   If a passcode is required on the display of the Bluetooth device, enter “0000”.
   For some radios you may need to press “Connect” after pairing and connection confirmation sound is heard by the earphone to establish the Bluetooth connection.

Pairing Process for Zello

1. Follow the same procedure as pairing with the phone.
2. Launch the Zello app.
3. Press “Options”->”Push-to-talk buttons”->”Add New Device”
4. Press the PTT Button once. You will see “PTT-Z” show up under “OTHER BUTTONS”. Click on it to select.
5. ou will see “PTT-Z” and “Connect”
6. Wireless PTT Pendant is now ready.

General specification

Troubleshooting:

device’s charging contacts are in contact with the optional desktop charging cradle. Check if the charging status LED is on (RED)
Battery not holding charge| Check if the battery is fully charged The battery has definite service life; replace the battery when it can’t give sufficient run time even when it’s fully charged. Contact the dealer to replace the battery.
Pairing issue| Cannot find the device, power off the radio/phone for 5 seconds, restart and search again for the device
RX / TX issue| Check Bluetooth connection and pairing.

Battery charging

• Use magnetic charging cable Charge Wireless PTT Pendant with the magnetic charging cable included, status LED indicates red while charging and turns blue when charging is complete. (Please ensure the USB wall charger adapter has an output of a minimum of 0.5A)

• Using a desktop charging dock

1. Single charging dock
   A. Connect the AC/DC adapter to the jack on the back of the charging dock.
   B. Ensure the device is properly installed and makes proper contact with the dock’s contacts.
   C. Status LED indicates red while charging and turns blue when charging is complete.

2. Multiple charging docks (Maximum 10 units)
   A. Connect the charging docks. DO NOT connector more than 10 units.
   B. Connect the AC/DC adapter to the jack on the back of any charging dock.
   C. Status LED indicates red while charging and turns blue when charging is complete.

Maintenance and safety:

Tips to ensure user safety, and optimal performance with a long usage life period.

• Avoid drop, collision, and piercing products.
• Keep away from hazardous, corrosive chemical substances.
• Keep away from heat, flame or high-temperature environment.
• Keep away from extreme cold, to avoid component damages.
• Close dust covers for earphone jack and charger jack when not in use.
• Store in dry and room temperature conditions.
• Do not charge with an unauthorized or damaged charger. Charging with a faulty charger may result in battery leakage, fire, and bursting.
• Do not charge the device with ambient temperature below 0°C (32°F) or above 45°C (113°F).
• Do not disassemble the product, it voids the warranty and increases the risk of water seal issues if the product is not assembled correctly. If the battery requires to be replaced, please contact your nearest service center for assistance.
• If the product is not used for a period of time, charge the product every 2~4 weeks to keep the battery well-conditioned.
• For prolonged storage, recommended storage temperature is 25°C (77°F). Charging the battery every 60 days will avoid the battery from getting deeply discharged and allow the protection circuit to activate.

Cleaning:

• Before cleaning makes sure the product is powered OFF, unplugged from the charger, and all dust covers properly closed.
• If necessary, the external surface of the speaker microphone may be cleaned with a mild soap solution and warm water.
• Do not use chemical solutions such as stain removers, alcohol, bleach, or oil remover as this may damage or corrode product surface.
• Make sure water trapped inside the speaker grill is shaken out before usage.

ATTENTION

This device complies with part 15 of the FCC Rules and ISED Canada license- exempt RSS standard(s). Operation is subject to the following 2 conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device can be used in portable exposure conditions without restriction.
The product is too small to place complete label information, so the label is placed on the packaging box.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>