national2way SM7-BT Wireless Speaker Mic 7 User Manual

national2way SM7-BT Wireless Speaker Mic 7

Model: SM7-BT
Wireless Speaker Mic. 7, Heavy Duty, Rechargeable Battery Powered, IP55, 3.5mm earpiece port
FCC ID: 2A2BD-SM7-BT

Product Overview:

Package contents

• On well GES-BTXM04, Bluetooth speaker microphone
• USB charging cable
• User’s Manual

Operation

• Power ON: Press power ON/OFF button ⑥, “Power on” sound is heard and status LED⑦ indicates purple, followed by flashing blue.
• Power OFF: Press power ON/OFF button ⑥, hold for 2 seconds until “Power off” sound is heard and status LED⑦ flashes purple once.
• Function Button: When the device is paired with a phone, Function button⑧ can be used as answer/end/reject calls, answer waiting call, switching between the active calls, and dial to the last called number.
• Torch light LED: Power ON device, press torch ON/OFF button ⑨ for approx. 1 second to turn on torch light LED④. Press and hold for 2 seconds to turn off.
• Volume control: Press volume up② or down ③ button to adjust volume. The device will produce a tone when volume reaches the minimum or maximum level.
• External earphone: Open external earphone jack ⑩ dust cover, plug listen-only earphone with Ø3.5 2pole or 3pole connector, loud speaker ⑤ will automatically mute.

Status LED

every 5 min
Pairing mode| Flashes Red & Blue alternatively
Connection| Flashes Blue one every 5 seconds
Unpaired or lost link| Flashes Blue twice every 3 seconds

Paring Process for radio / phone

1. Make sure GES- BTXM04 is OFF, press & hold power button ⑥ to switch on GES-BTXM04.
2. GES-BTXM04 is under pairing mode when the LED ⑦ flashes RED and BLUE alternatively and “Pairing” sound is heard.
3. Start Bluetooth function on your radio / phone.
4. Find the device name “BT-XM04” under Bluetooth device list and connect it.
5. Pairing process is completed.

General specification

Troubleshooting

device’s charging contacts are in contact with optional desktop charging cradle.
Check charging status LED ⑦ is on (RED)
Battery not holding charge| Check if battery is fully charged.
Battery has definite service life; replace the battery when it can’t give sufficient run time even when it’s fully charged. Contact dealer to replace battery.
Pairing issue| Cannot find device, power off radio/phone for 5 second, restart and search again for device
RX / TX issue| Check Bluetooth connection and pairing.
Unclear speech| Check if water is trapped in grill, shake mildly to get water out the speaker grill ⑤.

Battery charging

• Using Micro USB cable

Open dust cover and plug charger to Micro USB charging port⑪. After 1 ~ 2 seconds, status LED ⑦ indicates red while charging and turns blue when fully charged. Please ensure the USB wall charger adapter has output of minimum 1.0A. Close dust cover for maximum water protection when not charging.

Using desktop charging dock

1. Single charging dock

2. Connect the AC/DC adapter to the jack on the back of the charging dock.

3. Ensure the device is properly installed and makes proper contact with the dock’s contacts.

4. Status LED ⑦ of the device indicates red while charging and turns blue when fully charged.
   

5. Multiple charging docks (Maximum 5 units)

6. Connect the charging docks laterally. DO NOT connect more than 5 units.

7. Connect the AC/DC adapter to the jack on the back of any charger dock.

8. Status LED ⑦ of the device indicates red while charging and turns blue when fully charged.
   

Maintenance and safety

Tips to ensure usage safety, optimal performance with longer usage life period.

• Avoid drop, collision and piercing product.
• Keep away from hazardous, corrosive chemical substances.
• Keep away from heat, flame or high temperature environment.
• Keep away from extreme cold, to avoid components damages.
• Close dust covers for earphone jack and charger jack when not in use.
• Store in dry and room temperature conditions.
• Do not charge with unauthorized or damaged charger. Charging with faulty charger may result in battery leakage, fire, and bursting.
• Do not charge the device with ambient temperature below 0°C (32°F) or above 45°C (113°F).
• Do not disassemble the product, it voids warranty and increases risk of water seal issue if product is not assembled correctly. If battery requires to be replaced, please contact your nearest service center for assistance.
• If product is not used for a period of time, charge the product every 2~4 weeks to keep battery well-conditioned.
• For prolonged storage, recommend storage temperature is 25°C (77°F). Charge the battery every 60 days will avoid battery getting deeply discharged and allow protection circuit to activate.

Cleaning

• Before cleaning make sure product is powered OFF, unplugged from charger and all dust covers properly closed.
• If necessary, the external surface of the speaker microphone may be cleaned with a mild soap solution and warm water.
• Do not use chemical solutions such as stain removers, alcohol, bleach or oil remover as this may damage or corrode product surface.
• Make sure water trapped inside speaker grill is shaken out before usage.

This device complies with part 15 of the FCC Rules and ISED Canada license- exempt RSS standard(s). Operation is subject to the following 2 conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device can be used in portable exposure condition without restriction.
The product is too small to place complete label information, so the label is placed on the packaging box.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>