rock space RSD0620 AX3200 Smart WiFi 6 Router Installation Guide

rock space RSD0620 AX3200 Smart WiFi 6 Router

Meet Your Router

Connect the Hardware

1. Power on the new router. 2
2. Connect the modem or your main Ethernet cable (if your Internet connection does not require a modem) to the WAN port on the router. The WAN LED indicator turns
   on.
   

Configure the Router

Method 1: Via RS Home APP

1. Download the RS Home App.
   |
   ---|---
   

2. Connect your smart phone to the router.
   The default SSID is printed on the label at the bottom of the router
   
   

3. Launch the RS Home App.
   Note: If you are a new user, follow the onscreen instructions to register. With this App, you can manage your network easily and conveniently no matter where you are.

4. Select product model.
   After you log in to the account, the app will automatically pop up “Select Model” interface.Click “RSD0620-AX3200”.
   

5. The App detects your connection type automatically.
   If detection fails, choose your connection type manually. There are 3 connection types supported, please refer to FAQ > Q1 below.
   

6. Set your Wi-Fi Name and Wi-Fi Password.
   

Note: All pictures shown here are for illustration purpose only and actual pages may vary due to software update.

Method 2: Via a Web Browser

1. Connect to your router (wireless or wired).
   Wireless
   Find the SSID (network name) printed on the bottom label of the router and select the SSID from your network list to connect your device to the network.
   
   
   Wired
   Turn off the Wi-Fi on your computer and connect to the router via an Ethernet cable

2. Connect the router to the Internet.
   A. Launch a web browser and enter 192.168.0.1 in the address bar to log into the router’s web interface.
   
   B. Select the correct time zone for your location from the drop-down list.
   
   C. The webpage detects your connection type automatically. If detection fails, choose your connection type manually. There are 3 connection types supported, please refer to FAQ > Q1 below.
   
   D. Set your Wi-Fi Name, Wi-Fi Password and Login Password.
   Note: Enable the Encryption button to set your Wi-Fi Password, or your Wi-Fi will be public network.
   

Enjoy the internet!

Manage the Router

After setup, you can manage the router via any of the methods below.

Method 1: Via the RS Home APP

• Connect your smartphone to the router’s network.
• Launch the App and log in.
• Manage the router as needed.

Method 2: Via a Web Browser

• Connect your device to the router’s network. If you are using a computer, unplug the Ethernet cable if any.
• Launch a web browser and enter 192.168.0.1 in the address bar to log in.
• Manage the router as needed.

To check the full list of rock space Wi-Fi network devices, scan the QR code or visit https://rockspaceworld.com

FAQ

Q1: What connection type should I choose if the router fails to detect automatically?

• Dynamic IP (recommended) — Obtain IP address from ISP automatically, choose this option if your ISP does not provide username and password.
• Static IP — Choose this option if your ISP provided an IP address and other information.
• PPPoE — Choose this option if your Internet Service Provider (ISP) provided PPPoE username and password.

Q2: How can I reset the router?
Method 1: Launch the RS Home App, go to Device Information > More Settings, and click Restore factory setting. The router will reset automatically.
Method 2: Log in to the web management page, go to Advanced > Tools > System, click Reset. The router will reset automatically.
Method 3: With the router powered on, press and hold the Reset button for about 5 seconds

Q3: What if I forget my Wi-Fi password of the router?Method 1: Launch the RS Home app, go to More Settings > WiFi Setting to manage the Wi-Fi name and Wi-Fi password.
Method 2: Log in to the web management page, go to Wireless > Basic to reset your password.
Method 3: Reset the router to factory settings and create a new password. 

Q4: Why cannot my device connect to the 5GHz Wi-Fi signal?

• First make sure your device supports 5GHz band.
• If it does, check the status of the 5GHz network. Turn on the 5GHz Wi-Fi if it’s off through one of the following methods:
  A Via the RS Home app, go to More Settings > WiFi Setting.
  B Via a web browser, go to Wireless > Basic.

Q5: What if the App could not recognize or connect to the device?

• Check if the Ethernet cable with Internet connection is securely plugged into the WAN port rather than the LAN port.
• Check if your device is connected to the SSID of the router.
• Then, follow the steps below:

1. Navigate to Homepage;
2. Click “+” in the upper right to add your device;
3. The app will detect the device and click Next Step to get started.
   This is an approach you may adopt when you reconnect your device to the router but the connection fails.

**FCC Statement**

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device is restricted to be used in the indoor.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>