eta 3016 Cabero Electric Blender with Accessories Instruction Manual

eta 3016 Cabero Electric Blender with Accessories

USAGE PROCEDURE

CLEANING PROCEDURE

SAFETY WARNINGS
Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance. Check whether the data on the type label correspond with the voltage in your socket. The power supply plug has to be connected to a socket of electrical installation that conforms to respective standards. Never use the appliance if its power cord or plug is damaged, if it
does not work properly, if it fell down and was damaged or if it fell into water. In this case take the appliance to a special service to check its safety and proper function. This appliance must not be used by children. Keep the device and its supply cord out of reach of children. The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under supervision or they have been instructed about using the appliance safely and understand the potential dangers. Children must not play with the appliance. Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket. If the power cord of the appliance is corrupted, it has to be replaced by the producer, its service technician or a similarly qualified person so as to prevent dangerous situations. Be careful when handling the accessories immersion blender, the knife is very sharp. In case you are going to process hot liquid mixing a hot soup with vegetables etc be careful because it may spurt out of the container because of sudden boil. When handling the sickle- shaped knife, be very careful, especially when removing it from the chopping container, when emptying the container and while cleaning. The knife is very sharp.Always unplug the appliance from power supply if you leave it unattended and before assembly, disassembly or cleaning.The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providin accommodation with breakfast). It is not intended for commercial use. Do not insert or take the plug out of a socket with wet hands and do not pull the power cord. The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodatio with breakfast). It is not intended for commercial use.Do not use the appliance in connection with a programmer, a timer or any other. appliance that switches the appliance on automatically In case you are going to process hot liquid (mixing a hot soup with vegetables etc. be careful because it may spurt out of the container because of sudden boil.  Do not use containers without the anti-slip base!
Never immerse the drive unit into water or wash it in running water. Use the appliance in the working position only at places with no risk of its turning over and in sufficient distance from heat sources e.g. heater, electric/gas cooker, hot plate, grill, etc  and wet surfaces (e.g. sinks, wash basins, etc. Use the appliance designed for this type only. Using another appliance can represent a risk for the operator. Do not insert the appliance into any body holes. Remove the blade protectors from the knife before use. Before preparation, remove possible packages from food (e.g. paper, a PE bag, etc. Do not switch on the appliance without ingredients in it.Do not remove the appliance if the drive unit is in operation. Make sure that the power supply cable does not get between the rotating parts of the accessories. Before you remove the appliance or the drive unit from the container, let the rotating parts stop completely. Before emptying the chopping container, first remove the sickle shaped knife. Do not let children use the appliance without supervision. Do not process food at temperature exceeding about 80 °C (176 °F).
Do not use the hand blender in containers, in which you heat food at the same timeusing heat sources (e.g. heater, electric/gas/induction cooker, hot plate etc. When blending, mixing, beating liquids never put in a bigger amount than specified onthe containers and do not exceed the recommended times of processing specified in the tables.  Never insert e.g. fingers, fork, knife, spatula, spoon into rotating parts of the appliance and the accessories. Never put fingers in the filling hole and do not use a fork, a knife, a spatula, a spoon etc. for the same. Use only the provided pusher for this purpose. If the processed food starts to stick to the appliance e.g. on knives, beater, container or lid), switch off the appliance and clean the accessories carefully e.g. using a spatula.Check the condition of the power cord of the appliance regularly. Do not wind the power cord around the appliance; this will extend life of the power cord. The power cord must not be damaged with sharp or hot objects, open fire; it must not be sunk into water or bent over sharp edges. Never put it on hot surfaces or do not let it hang over the edge of a table or work tables. Hitting, stumbling over or pulling the power cord e.g. by children can result in tilting over or drawing the appliance down and serious injury. If you need to use an extension cord, it has to be uncorrupted and it has to comply with the valid standards. Never use the appliance for any other purpose than that described in these instructions for use. The producer does not undertake any responsibility for damage caused by improper use of the appliance and the accessories (e.g. food deterioration, injury caused by the knife blade, fire, etc.

DESCRIPTION OF THE APPLIANCE AND ITS ACCESSORIES

• A  drive unit
  • A1 speed switch (ON) A4 – power supply control light
  • A2 speed regulator A5 – adapters blocking buttons
  • A3  display A6 – power cord
• B blending adapter
• C  beater (only for type ETA 2016, ETA 3016)
  • C1  gear
• D double-beater (only for type ETA 3016/010, ETA 6016)
  • D1 gear
• E mixing/beating container 800 ml only for type ETA 3016, ETA 3016/010, ETA 6016
  • E1 anti-slip base/lid
• F  small chopping container 500 ml only for type ETA 3016
  • F1 central shaft
  • F3  container lid
  • F2  sickle-shaped knife
  • F4  hole for drive connection
  • F5  anti slip base
• G  large chopping container 1250 ml (only for type ETA 3016/010 and ETA 6016)
  • G1 central shaft G3 – container lid
  • G2  sickle-shaped knife G4 – hole for drive connection
  • G5 slip abnatsie
• H Multipu rpose mntainecro
  • H1 central shaft
  • H2 lid lock button
  • H3 container lid
  • H4 hole for drive connection
  • H5 filling hol
  • H6 pusher
  • H7 anti-slip base
  • H8  sickle-shaped knife
  • H9  graters holde
  • H10  cutting grat
  •  H11  slicing grater
  • H12  tearing grater

PREPARATION FOR USE

Remove all packing material and take out the hand blender and the accessories. Remove all possible adhesion foils, stick-on labels or paper from the appliance. Before the first use, wash the parts that will be in contact with food in hot water with a detergent, rinse thoroughly with clean water and wipe till dry, or let dry. Put the hand blender with the selected accessories on a flat, stable, smooth and clean work surface at the height of at least 85 cm, out of reach of children and incapacitated people Make sure that the power cord is not damaged and that it does not lead through any sharp or hot surfaces. Plug power supply fork A6 to the electric power and control light A4 will come on. Choose the amount of the processed food so that the maximum volume of the containers marked with the gauge line is not exceeded.Bigger amount of processed food has to be divided into several doses and the volume of the containers has to be checked regularly. Any time you work with the appliance, do not forget to put an anti-slip base under container E, F, G, H. We recommend stopping work from time to time, switching off the appliance and removing possible food that was stuck onto the blending/beating adapter, the sickle-shaped knife, graters, containers or the lid. Food preparation (processing) times are only approximate, they depend on the amount, the kind and the quality of used ingredients and they range in seconds to minutes (see the table). After finishing work, disconnect the appliance
from power supply by taking the connector of power cord A6 out of the electric socket. Container E is suitable for use in a microwave oven.

Switch (A1)

Start the drive by pushing the switch (the motor runs only for the time when the switch is pushed and at the output set by the electric regulation.

Electronic revolutions regulation (A2)

It enables setting optimum revolutions for the selected chopping, blending, mixing, beating, cutting and grating adapter. By turning the regulator from – to + you can continuously change the speed of the motor revolutions. The set speed value 1 to 8is shown at display A3. According to the method of use of the accessories we recommend the following speed setting

• Blending adapter: 1 – 8
• Beating adapter : 3 – 8
• Sickle-shape knives:1 – 8
• Graters:1 – 8

Mounting and removing drive unit (A)

Insert the drive unit by slight pushing into the connecting hole of the respective adapter  till the blocking snaps in (you will hear snapping noise). Remove the drive by pushing both locking buttons A3 and remove the unit by slight pulling.

Mounting and removal of beating adapter (C, C1)

Push beating whisk C slightly to gear C1 to the maximum positionyou will hear snapping sound). Remove the beating whisk from the gear in the opposite direction.

Mounting and removal of beating adapter (D, D1)

Push beating whisk shafts D slightly to gear D1 to the maximum position (Fig. 5), (you will hear a snapping sound). Remove the whisks from the gear in the opposite direction.

Mounting and removal of lid (F3, G3)

Put the lid onto the respective container F or G so that the lugs on its edge snap into the moulded holes in the container and secure the lid by clockwise movement to the maximum position  You can remove the lid from the container in the opposite direction.

Mounting and removal of lid (H3)

Put the lid on multi-purpose container H so that the lugs on its edge snap into the moulded holes in the container. Bend interlock H2 by slight pushing and turn the lid in the clockwise direction to the maximum position. Then release the interlock. Now the lid is secured in the right position. You can remove the lid from the container in the opposite direction.

Mounting and removal of sickle-shaped knife (F2, G2, H8)

Hold knife at the upper plastic part, remove the protective cover and put it in the container so that it is inserted on the shaft with its central hole and give it a turn to lock into place
You can remove the knife from the container in the opposite direction.

Mounting and removal of graters (H10, H11, H12)

Insert the grater into holder H7 with the blade up and secure it by slight pushing you will hear snapping sound. The grater must be in line with the holder. When taking it out, first of all release the grater by pushing on the protrusion from the bottom of the grater and then remove the grater easily from the holder.

Mounting and removal of holder (H9)

Hold the holder (with installed grater) at the upper plastic part and put it in the respective container so that it is inserted on the shaft with its central hole.You can remove the holder from the container in the opposite direction.

USING ACCESSORIES

Please consider the following tips for preparing food as examples and inspiration, the purpose of which is not to provide instructions, but to show various possibilities of preparing food.
Blending adapter (B) Be careful, knife blades are very sharp! The blender is intended for mixing liquids, juices, milk shakes, milk, sauces, soups, mayonnaise, children‘s and dietary food, for making purée, etc. Hold hand blender A with your hand and put blending adapter B into container E filled with food. Hold the drive unit and the container firmly. Start the drive unit by pushing switch A1. When working, move the blender in the container to process the food thoroughly. Food will be processed in about 10 seconds to 2 minute. After finishing work, release the switch, remove the blending adapter from the container and clean it.

CAUTION
The maximum time of processing is 2 minutes. Then wait for 10 to 15minutes, which is necessary for the drive unit to cool down.

Recommendation

• It is recommended to cut tough ingredients into small pieces. Do not process very hard materials e.g. ice cubes, etc. The knife would be blunt soon.
• Hard ingredients (e.g. legumes, soya beans, etc should be soaked in water before processing.
• The longer you process the food with the blender, the smoother the result will be.
• In the case of liquids that create foam e.g. milk, never fill container E up to the MAX gauge mark to prevent overflowing.
• If you are not satisfied with the result, switch off the appliance, mix the ingredients with spatula, take some part of the ingredients or add a little liquid.
• You can use anti-slip base E1 and a cover for container E to store food e.g. in a efrigerator.

Amount of food and processing time Food

Small chopping containe

r (F) 500 ml, big chopping container (G) 1250 ml, multi-purpose container (H) 1250 ml. Be careful, knife blades F2, G2, H8 are very sharp! Do not use the knife for processing any dough! It is intended for chopping (mincing), blending, mixing all kinds of tough food e.g. fruit, vegetables, nuts, almonds, hard cheese, boiled eggs, meat – without bones, tendons and skin or for preparing purée.Put knife F2, G2 or H8 into the respective container F, G or H.Put food into the container. Put respective lid F3, G3 or H3 onto the container and secure it.Connect the drive unit to the lid (Fig. 3). Hold the drive unit and the container firmly. Start the drive unit by pushing switch A1. Food will be processed in about 10 seconds to 2 minute. After finishing work, remove the knife in the opposite direction.

CAUTION
The maximum time of processing is 2 minutes. Then wait for 10 to 15 minutes, which is necessary for the drive unit to cool down.

Recommendation

• Before processing, cut bigger pieces of food into cubes of about 3 x 3 x 3 cm.
• Never crush very hard ingredients with the sickle-shaped knife, such as coffee beans, nutmeg, ice cubes etc.
• The knife would be blunt soon.
• Hard ingredients (e.g. legumes, soya beans, etc should be soaked in water before processing.
• The longer you process the food, the smoother the result will be.
• If you chop hard cheese or chocolate, work for a short time.
• It is because the ingredients are heated excessively by chopping, they become softer and they can become cloddy.
• In excessive crushing of extremely hard food e.g. ice cubes, nutmeg, coffee beans, grain using the sickle shape knife it gets blunt more quickly.
• If this happens, sharpen the blade of the knife.
• You can use anti-slip base F5, G5 as a cover for the respective container to store food e.g. in a refrigerator.

Amount of ingredients and time of processing, small chopping container

(F)

Amount of ingredients and time of processing,big chopping container (G)

Food| Maximum amount| Time| Speed
Herbs| 125 g| 20 x 1 s| 8
Onions and eggs| 450 g| 15 x 1 s| 4 – 8
Meat, fish| 400 g (max.)| 30 s| 8
Nuts| 300 g| 60 s| 8
Cheese| 125 – 300 g (max.) 45 s| 8

Multi purpose container 1250 (H)

Be careful, grater blades H8, H9, H10 are very sharp! Graters are intended for cutting, chopping, slicing of all kinds of tough food (e.g. fruit, vegetables, mushrooms. Insert the selected grater into holder H9 and secure it by slight pushing. Then insert the holder into container H. Insert lid H3 on the container and secure it. Connect the drive unit to the lid. Hold the drive unit and the container firmly. Start the drive unit by pushing switch A1. Food will be processed in about 10 seconds to 2 minute. After finishing work, remove the grater in the opposite direction.

CAUTION
The maximum time of processing is 2 minutes. Then wait for 10 to 15 minutes, which is necessary for the drive unit to cool down.

Recommendation

• Always add food intended for processing only after mounting the accessories.
• Always cut big pieces beforehand so that they can get into the filling hole.
• Put in the ingredients one after another and equally.
• Always move food in filling hole H5 using pusher H6 only, move it slowly and to not push downwards too much.
• When processing a big amount of food, make sure it does not accumulate under the disc. Empty the bowl more often.
• If food is grated roughly (e.g. breadcrumbs), use the sickle-shaped knife for finer grinding.
• When grating or granulating soft ingredients, use low speed so that ingredients do not turn into mash.
• Use the sickle-shape knife that is also intended for chopping (grinding) for food that you usually grate hard cheese, nuts, chocolate.

MAINTENANCE

Unplug the appliance from power supply by taking the plug of the power cord out of a socket! Do not use rough and aggressive detergents. Clean drive unit A, gear C1, D1 and lids F3, G3, H3 with a soft and wet cloth with a little detergent. Make sure that water does not get inside the appliance. Wash the accessories in hot water with a detergent right after use, rinse it in clean water and wipe till dry (you can also wash the accessories in a dishwasher – but not blending adapter B. The end piece with a shaft of adapter B must not be immersed during cleaning. Be very careful when cleaning the hand blender, the sickle shaped knife and the graters. Make sure that the cutting edges of the accessories are not in contact with hard objects that make them blunt and thus they reduce their effectiveness. Some food can colour the accessories in some way. But this does not affect the function of the appliance and it is not a reason for a claim. This colouring usually disappears after some time. Never dry plastic moldings over a heat source (e.g. heater, electric/gas stove). Store the appliance after cleaning at a dry, dustfree and safe place, out of reach of children and incapacitated people.

TROUBLESHOOTING

the plug and the socket
Drive unit gives out strange smell| When you turn it on for the first time, it can give out strange smell| This is not a defect nor a cause for a complaint regarding the appliance
Drive unit is hot when touched| Processed food is too heavy or recommended times of processing were exceeded| Switch off the appliance, let it cool down, divide the processed food into smaller portions and process them gradually
The appliance stops working| Knives, the blending adapter and graters blocked by hard ingredients not recommended for individual adapters| Switch off the appliance, remove the ingredients that were blocking the accessories and then continue work

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be taken over free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authorities or in the nearest collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. If the appliance is to be put out of operation for good, after disconnecting it frompower supply we recommend cutting off the power cord and thus it will not be possible to use the appliance again.More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service. Failure to comply with the instructions of the manufacturer will lead to expiration of the right to warranty repair.

TECHNICAL DATA

• Voltage (V) specified on the type label
• Input (W) specified on the type label
• Weight about (kg)0.8

The product has received ES declaration of conformity according to Act as amended. The product matches the requirements of the below statutory order as amended. Committee Regulation No. 2006/95/ES as amended, setting the technical requirements of the electrical appliance as low. Committee Regulation No. 2004/108/ES as amended, setting the technical requirements of products in terms of their electromagnetic compatibility.
The product is in conformity with the European Parliament and European Committee Regulation No. 1935/2004/ES re. Materials and objects designed for contact with food.
The manufacturer reserves the right for any insignificant deviations from the standard finished product which do not have any effect on the functioning of the product.
HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS. TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY. PRODUCER: ETA a.s., Zelený pruh 95/97, 147 00 Praha 4 Bráník, Czech Republic.

References

• ElektroEko – Odbiór odpadów elektro
• Úvod | ELEKTROWIN, a.s.
• Úvod - Envidom
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>