JADE BS-44 Wall Mounted Speaker Instruction Manual
- June 5, 2024
- jade
Table of Contents
JADE BS-44 Wall Mounted Speaker
UNDERPOWERING VS.OVERPOWERING
2-CHANNEL AMPLIFIER WITH 80 OUTPUT
- Observe correct Polarity for maximum Bass performance
TECHNICAL SPECIFICATIONS
| Model | BS-44 |
|---|---|
| Woofer | 4” Paper cone with foam edge |
| Tweeter | 0.5” Dome 180 degrees dispersion. |
| Impedance | 4 ohms |
| Power | 60W MAX. 20W RMS |
| Frequency response | 90Hz-18KHz |
| Sensitivity | 86dB |
| Dimension (H×W×D) | 182x130x102mm |
| Color | White |
| Net Weight | 1.1kgs |
| Model | BS-48 |
| Woofer | 4” Paper cone with foam edge |
| Tweeter | 0.5” Dome 180 degrees dispersion. |
| Impedance | 8 ohms |
| Power | 60W MAX. 20W RMS |
| Frequency response | 90Hz-18KHz |
| Sensitivity | 86dB |
| Dimension (H×W×D) | 182x130x102mm |
| Color | White |
| Net Weight | 1.1kgs |
Introduction
Thank you for buying wall mount speaker. Please read and have a thorough understanding of the entire manual before installation and use Keep the manual for maintenance.
Read these instructions carefully before using the product
- When the speakers are installed in walls, check that the wall structure is reliable and that the speaker is firmly attached. The user should be responsible for this very thing.
- Do not install the speakers in fine wood or soft wall material because the screws can get loose, causing the crash or breakdown of the speakers and personal injury.
- Do not use nails, adhesives or other unauthorized devices. Long-term use and vibrations may cause it to fall easily.
- Do not place the speakers on a turntable or movable support.
- Do not touch or bump the woofer and tweeter. If these are damaged, the sound will be distorted.
- Do not listen to sound at a very high level when you are changing the input source(for example, to tune FM/ CD) installation or removal of cables should make sure that the power amp/amplifier device radio is turned off.
- Do not attempt to clean the speakers with chemical solvents as this may damage the paint surface. Clean with a dry cloth.
Users have a responsibility to place or install safety
The speakers that are placed in the holder can be either wall or ceiling type, using screws to be placed inside of the speakers in the back is optional.
- Mark the mounting bracket as a template with the regional location of the hole slots.
- Then use the appropriate hardware and tools(not supplied) are properly fixed to the bracket wall/ceiling.
- Place the speakers to the bracket using the screws and washers according to the speaker.
Connection
Use wire on the back of the speaker in the output tab of the amplifier(or
amplifier of radio). The speaker wire is on one side red and on the other one
black. Connect to the red side of the amplifier and speaker(+)tab. Connect one
end of the black side(-) in the other tab. Connect each speaker to make sure
that is no (+,-) inverted polarity. If the polarity of the speakers is
reversed, the sound will be unnatural and will play without bass.
- Fasten the bracket to on the wall with 2 pcs screws
- Connect the speaker cable to the terminal(“+” to“+”,“-” to“-”+)
- Screw the two knobs
- Fasten the screws after horizontal rotation
UNDERPOWERING VS. OVERPOWERING
- Most speaker damage is caused by amplitiers with too litde power(wattage).
- An overdriven amplitier dips the waveforms and sends distortion to the speakers.
- Clipping is usually audible; it may vary from a harsh sound to a fuzzy or unclear sound.
- you hear this condition at loud volume levels, turn down the volume untl the distortions no longer present.
- Damage caused by operating the speakers at distorted volume levels is not covered by the warranty.