COSTWAY FP10015 Dishwasher User Manual

FP10015 Dishwasher
User Manual

Every appliance has passed the water test in the factory. It is normal if you found some water left in the appliance. Please feel free to use it
Please read this instruction carefully before using it and keep it safe.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using your dishwasher, follow basic precautions, including the following:

• Read all instructions before using the dishwasher.
• Use the dishwasher only for its intended function.
• Use only detergents or wetting agents recommended for use in a dishwasher and keep them out of the reach of children.
• When loading items to be washed:

1. Locate sharp items so that they are not likely to damage the door seal; and
2. Load sharp knives with the handles up to reduce the risk of cut-type injuries.

• Do not wash plastic items unless they are marked “dishwasher safe” or the equivalent. For plastic items not so marked, check the manufacturer’s recommendations.
• Do not touch the heating element during or immediately after use.
• Do not operate your dishwasher unless all enclosure panels are properly in place.
• Do not tamper with controls.
• Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.
• To reduce the risk of injury, do not allow children to play in or on a dishwasher.
• Under certain conditions, hydrogen gas might be produced in a hot-water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for such a period, before using the dishwasher turn on all hot-water faucets and let the water flow from each for several minutes.  his ill release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.
• Remove the door to the washing compartment when removing an old dishwasher from service or discarding it.
• Do not run the appliance in a humid environment in case of triggering electricity leakage or getting rusty.
• Tableware may be hot after washing in the appliance, please remove them around 30 minutes after the procedure ends.
• The appliance runs automatically. Do not inject or pour water into the appliance during working in case of overflowing and causing malfunctions.
• Do not move or tilt the appliance during working in case of triggering water or electricity leakage.
• Do not open the door of the dishwasher in case hot steam in it may get you injured. For putting in or taking out tableware, please press the stop button, open a gap to let out the team, and wait for 10 seconds.
• Children should not play with the dishwasher. Keep them away from the appliance especially when the door of it is open.
• Unplug the plug from the wall socket and disconnect the water pipes after not using them for a long time. 40cm (15.7” )
• Do not clean the dishwasher with corrosive detergent in case of damaging it.
• Do not use detergents other than exclusive ones for dishwashers.
• Cut the ribbon on the power cord and the water pipe with flat scissors when unpacking the package in case of hurting the pipes and cords.
• Use warm/cold water as a water source. Please use the rated water temperature of 120 F.
• Protective plastic bags should be kept from children and cut into pieces for disposal.
• Do not disassemble the appliance by yourself.
• Plug the appliance into a grounded socket. A grounded socket can reduce the current at most when there is an accidental electricity leakage which can protect the user most.
• Do not use the appliance during thunderstorms.
• The drain pipe should not be hung more than drain pipe blockage, water, or electricity leakage.
• Check if the appliance is installed well before running the appliance, please check if the water pipes and power cord is connected properly.
• Tableware with a sharp end should be placed downward to avoid hurting users when taking them out.
• Do not operate the appliance if its power cord is damaged, please contact customer service for help.
• Do not keep the door of the appliance open in case it falls due to the imbalance.
• Do not cover the wall socket with any foreign objects. Do not connect the appliance to an outer timer, plug it into a multi-slot socket or a socket that is not grounded. Doing so may cause damage or injuries.
• Dishwasher detergent and polishing detergent should be placed beyond children’s reach due to the danger of children playing or accidentally eating this acidic/alkaline detergent. over the appliance. Doing so may cause

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.
WARNING -Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt about whether the appliance is properly grounded. Do not modify the plug provided with the appliance, if it will not fit the outlet, have a proper outlet installed by a  qualified electrician. Please do not use a power strip
SAVE THESE INSTRUCTIONS

Product Overview

• Parts of Dishwasher
  

• Technical Information

Due to the continuous improvement of products, such as the technical parameters in this manual are modified without prior notice.

• Package List

Please check the accessories one by one after you open the box. Please contact the seller if there is any shortage or damage.

NOTICE:  Please use flat scissors to cut the tie of water pipes and power lines.

INSTRUCTIONS

• Installation diagram

Running water inlet This method is applicable for the kitchen with the great condition that hoses and cords are placed well. Detail steps ll and El are listed below.
NOTICE: A hose that attaches to a sink spray can burst if it is installed on the same water line: as the dishwasher. If your sink has one, it is recommended that the hose be disconnected and the hole plugged.

Installation steps

1. Installation of the inlet pipe

2. Installation of the drain pipe

1. Connect the drain and drain port
2. The drain pipe should be fixed by the clamping band
3. Please put the free end of the drain pipe into the sink or sewer.

Notes:

1. Water injected into the dishwasher should be at a temperature lower than 120° F.
2. A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. : disconnected and the hole plugged. If your sink has one, it is recommended that the hose be disconnected and the hole plugged. } Installation steps
3. The inlet pipe and drain pipe can not be folded, otherwise may affect the washing effect ‘
4. Ensure that the appliance is situated securely on the floor; otherwise, it will cause overflow and electric D Installation of inlet pipe leakage. Take the package out from the appliance.
5. After installation, please retain all documents and components for later use or for the subsequent owner

WARNING: C ertain internal parts are intentionally not grounded and may shock only during servicing. Service Personnel-Do does not contact the following parts while the appliance is energized: drain pump, PTC heater.

• Installation of water tank

In addition to the previous installation mode of suctioning water, you can also choose this installation mode for the water tank, as shown in the following steps.

1. insert the injection pipe of the water tank into the injection of the water tank as shown above.
2. After placing the water tank on the table horizontally, put the dishwasher onto it aligned with the groove.
3. .Put the injection pipe connector of the water tank onto the suction port of the dishwasher and put the plastic stopper on the injection port in case of leaking of water.

• Water tank use

Notes:

1. Before pouring water into the water tank, Please check if the appliance is on, both the drain and inlet hose is connected well.

1. Open the drawer of the water tank and pour water into it. Pay attention to controlling the speed of pouring water in case of spilling.

2. When pouring water into the tank, the appliance will beep and the icon marked above will light up if the water tank is full. Stop adding water and push the drawer back to the appliance .

OPERATING INSTRUCTIONS

• Control panel instruction

1. Operate the dishwasher
2. Overview of programs
   you can delay the start of the program by up to 24 hours.

**Lock**| It means button lock. You can protect the appliance from unexpected termination of the program (e.g. improper operation by children). Activating the button lock: Hold down the button for 3 seconds until the icon is indicated on the digital display. Deactivating the button lock: Hold down the button rep for 3 seconds until the icon goes out.
---|---
**Preserve**| The Preserve program is able to preserve tableware with great air ventilating conditions which can prevent tableware from getting mildewed, damp, or bad smell. After finishing the washing procedure, “on” shows on the screen and it means that the dishwasher is working at the Preserve program which will last for 24 hours. To stop the Preserve program, press the “Preserve” button until “OFF” shows on the screen.
The indicator lamp means water shortage. The icon means that the water in the water tank is full.

• Overview of programs

Special dishwasher detergent will remove oil and food residues. It is a must every time you use the appliance. The detergent dosage depends on the amount of and type of soiling.

Program

| Type of soiling| Consumption of detergent| Time cycle
---|---|---|---
washing powder/washing tablet

ECO

| Part dried, common household food remnants| 9g| 1 pc| 2:25

Normal

| Little dried, normal household food remnants| 9g| 1 pc| 1:00

Intensive

|  Very adhesive burned-in or dried-on food remnants| 9g| 1 pc| 2:00

Rapid

| Fresh food remnants, Light and less oil.| **_**|

**_**

| 0:35

Glass

| Slightly adhesive, temperature-sensitive plastic and glasses| 9g| 1 pc| 1:30

Notes: Please don’t overuse the detergent. The excessive detergent will not only produce a lot of bubbles but also affect the cleaning effect. Please choose a suitable washing tablet, you should use the small one for this appliance.
The actual runtime of each program is possibly different from the preset time cycle due to the water temperature, the number of utensils, the type of soiling, and the recovery of water softening. It is a normal condition, please use it with confidence.

• Add detergent

after the basket is pushed in. Add the required amount of detergent Please put the detergent in the designated place.

• Utensils selection

Dishwasher-proof utensils:
Utensils notes:

1. Precious metal, aluminum, and colored glaze utensils may turn cloudy after being washed in a dishwasher.
2. Cutlery made of bamboo or wood It may come loose or crack at high temperatures.
3. Plastic items: Please see the manufacturer’s instructions for plastic cutlery or items with plastic parts, because these items may come loose or crack at high temperatures.
4. Cleaning cloth: Cleaning cloth may cause dishwasher fault.
5. Cast iron items: Cast iron items may rust after being washed in a dishwasher.

• Tableware placement attention

1. Remove large food remnants such as bones or leaves;
2. All utensils with dirt should be face down. It their opening face or closing face down will leave the water on the top.
3. Utensils are secure and cannot tip over, one place to one utensil.
4. Do not let the utensils out of the basket to obstruct the rotation of spray arms.
5. The small size of utensils might drop out from the basket and obstruct the spray arms rotation, Please do not put these small items in the appliance.
6. When pushing the basket back, do not let the sharp parts of the utensils cut the seal.
7. The top coat of the basket can not be scratched, or it will be rusted.
8. Place cutlery, always unsorted with the tips faces down, in the cutlery basket.

TIPS: Flip the spray arm after the basket is pushed in. to check if the spray arm still can be rotated.

• Loading the basket

USER-MAINTENANCE INSTRUCTIONS

• Clean the filter assembly

After the appliance ran a while, there will be some residue and other things left in it. Please clean it when you see the residue and things, and also clean the appliance immediately.

**A**
Make sure that the power is turned off. Rotate the filter assembly counterclockwise to remove it for leaning. And turn it clockwise to put the filter assembly back in place.| **B **Rinse the filter assembly with running water, do not use steel wool or iron brush, otherwise, it will scratch the filter and cause it to rust. l
---|---

• Clean the spray arms

**A**
Pull out the main basket from the appliance, and then slightly raise the lower spray arm to prevent the clip from falling.| **B**
Rotate the upper sprayer counterclockwise to remove. And turn the spray rm clockwise to put it back.| **C**
Check whether the spray arm is blocked. If so, use a thin wire to pull out the blockage or flush the hole with water.
---|---|---

• Clean dishwasher interior

Leaking seals and door seals should be cleaned with a damp cloth. To clean the dead corners inside the dishwasher, please clean it with citric acid and a damp cloth. Please use a special detergent to clean the liner and internal pipes of the dishwasher according to the instructions.

Service Information

• Error code list

department
E02| Thermistor open circuit| Please contact the after-sales service department
E03| The machine is not heated| 1. Please make sure the utensils be placed correctly. If the utensils are facing up and there is water in the plates/bowls, the dishwasher indicates a lack of water.
2. Please contact the after-sales service department
E04| Inlet valve failure| Please contact the after-sales service department
E05| Overflow| 1. Lean the appliance about 30 to 45 to pour out the water on the bottom plate, 2. Check if the drainage pipe is placed too high
3. Check if the pipe is knotted blocked pressed,
4. Check if the appliance is placed correctly
5. Exclude the above cause, try to restart the appliance Please contact the after-sales service department.
E06| Heating function abnormal| Please contact the after-sales service department
E10| Water inflow abnormal| 1. The tap was not fully opened.
2. Small inflow and low water pressure.
3. Start—up multiple times in case of water shortage.
4. Please contact the after-sales service department.

• Common fault approach

of the spray arm have been blocked, and the washing powder can not be flushed out.| Clean the holes of the spray arms and run the quick wash mode again to clean the utensil.
2. Put too much washing powder.| Run the quick wash mode again and put mode rate washing powder as instructed next time.
3. Used low—quality washing power| Use specialized washing powder and washing tablet with quick wash mode to wash the utensil again
4. Improper placement of detergent| Refer to section “Adding detergent”
Some drops in the inner liner| It’s normal and it won’t impact the utensil|
Some foam in the liner| Didn’t use specialized washing powder or put too much washing powder in it| If there is not too much foam, you can open the door to make the foam less and less, if there is too much foam, you can use a tool to remove it. Finally, restart any program for about 3 minutes, and then execute it again until the bubbles disappear.
Utensils are wet| 1. Utensils be piled up and without lean| Refer to utensils place rule
2. The washing process is still running| Wait until the process finished
3. Programme selected without drying| Select program with drying (See an overview of programs.)
Problem| Cause| Remedy
---|---|---
The appliance makes the noise as blowing something when is pluggin9. And the display shows FAN’.| The air renewal system is working| Its normal situation
No reaction after turning on the power| lit all the lights were off and no reflection when you press the button. there are possibilities that you didn’t plug in the power or the power was a blackout.| Please plug the power in and make sure the power has no issue.
2. Power is cut off| Clean theopner plug and make sure if
3All the kph is on. II might be on the childproof locking mode.| Unlock the childproof lock
4. The time that the touch power icon is too short.| Press the power icon for 1 second
Have no reaction when pressing any button except the power bottom| 1. Have not closed the door.| Close the door.
2. There is greasy dirt or water on the glass and hand.| Clean the power plug and make sure its dry.
3All the kph is on. it wrght on the childproof locking mode.| Unlock the childproof lock
4. PCS lock of the door is broken| Please contact the after-sales service department.
The watertight control panel Is lighting when water comes in.| 1. Check if the water supply has a problem| make e sure the water supply has no
2. The flowmeter is broken| Please contact the atter sales service department.
3. The filling valve is broken| Please contact the after-sales service department.
The water light in the control panel is lighting when water comes in from the Suction pump.| 1. There is no water in the container or the suction pipe is not in the water.| Please add water to the container and make sure the suction pipe is in the water
2. Dirty clogging of suction pipe filter| Clean the filter screen of the suction pipe
3. The filling valve is broken| Please contact the after-sales service department.
The water intake time is longer when water comes in from the suction pump| It’s normal and be free to use| /
Have crashing noise when it is working| Place the utensil in an improper way some utensils is obstructing the spray arms: or some utensils are crashing each other.| Unload the dishwasher and replace the utensils in a proper way
The utensil was not cleaned up| utensils be piled up and without lean| Refer to utensils place rule
2. Do not choose the right program of washing| Please choose the right program for washing
3.00 not use specialized washing powder or put too little washing power.| Use specialized washing powder and put enough of it before washing
4. Do not install the filter in the right position and the food remnants get in it| Re—install the filter in the right position
5. The spray arms were blocked| Clean the inner part of the spray arms
6. The spray arms are stuck| Check if the spray arm is stuck by the utensil
7 Some food remnants are sticking to the utensil| Soak the utensil for a while before washing
blackout when the appliance is working| Restart the washing program
9 Some food remnants are too hard to wash| Suggest wash utensil with steel wool before putting it in the appliance to wash
A lot of water was left in the appliance when is not working| 1. The position of the drainage pipe is too high| Refer to drainage pipe installation
2. The drainage pipe Is tied. blocked or pressed by something heavy| Untie the pipe and remove the heavy thing
3. Drainage pump is broken| Please contact the atter sales service department.
4. The filling valve is broken| Please contact the atter sales service department.

If the solutions above can not fix the problems, please stop to use the appliance immediately and cut off the power and water supply. Please contact the after-sales department.

• Circuit diagram

STATEMENT:
With the innovation and improvement of product technology, the product specifications of the same model as this product may be changed, and the change part will be notified without further notice.
The pictures of the products in the instruction are all borrowed from the appearance of the dishwasher, and the pictures are only used as an example. The actual appearance should be based on the purchased products.
As a result of product improvement, the execution standards of product manufacturing may be hung, and the revised standards of execution will be changed.
There is no retroactive effect on the sold product.

With your inspiring rating, COSTWAY will be more consistent to offer your EASY SHOPPING EXPERIENCE, GOOD PRODUCTS, and EFFICIENT SERVICE!
US office: Fontana   http://www.costway.com/hysalesrule/qr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>