COSTWAY HW65-8CK-206 52 Inch W Walnut Entertainment Center Instruction Manual
- October 30, 2023
- COSTWAY
Table of Contents
COSTWAY HW65-8CK-206 52 Inch W Walnut Entertainment Center Instruction Manual
Before You Start
Read each step carefully before starting. It is very important to ensure each
step followed in correct order, otherwise assembly difficulties may occur.
Most of board parts are labeled or stamped on the raw edges. Have a check to
make sure all parts are included.
Work in a spacious area, preferably on a carpet close to where the unit will
be used.
Keep the handtools close at hand. Do not use power tools to assemble your
furniture. They may scratch or damage the parts.
Notice
- 50% tighten before fixing all screws. Allen wrench is recommended instead of an electric drill.
- Place the item on a flat ground to adjust and make sure it remains stable.
- Tighten up all screws with tools gradually.
- If the screws are not aligned with holes during assembly, please loosen all the other screws to 50% and continue the assembly process.
- If the item is not stable, please loosen all the screws, adjust it on a flat ground and tighten up all screws again.
- Note: If one or some screws are fully tightened during assembly, the others may not be aligned with the holes. In addition, all the holes are designed to be relatively larger to provide more space for the adjustment of the screws.
Part List
-
TOP 1 pc
-
BASE 1 pc
-
CENTER (L)1 sp
-
SIDE (L) 1 ps
-
SiDE (R) 1 pc
-
CENTER (L)1 pcs
-
CENTER (R)1 pcs
-
CENTER UP 1 pcs
-
SHELF 2 pcs
-
BACK PANEL UP 2 pcs
-
BACK PANEL SIDE 2 pas
-
GLASS DOOR 2 pcs
-
DRAWER FRONT 2 pcs
-
DRAWER SIDE (L) 2 pcs
-
DRAWER BACK 2 pcs
-
DRAWER BASE 2 pcs
-
DRAWER SIDE (R) 2 pcs
-
BACK PANEL (MID) 1 pc
-
BASE RAIL 1 pc
-
SUPPORTING LEG 1 pc
Description
|
Hardware
|
Spec
|
Qty
---|---|---|---
A Minifix (S)| | | 21pcs
B Wood Dowel| | 8x35mm| 38pcs
C Cap Bolt| | M6x5Omm| 9pcs
D CSK Screw| | 3.5x12mm| 24pcs
E Tapping Screw| | 3x19mm| 12pcs
F CSK Screw| | 4x16mm| 8pcs
G CSK Screw| | 4x32mm| 8pcs
H Handle| | | 4pcs
I Handle Screw| | 4x18mm| 8pcs
J Hinge| | 5/8″| 4pcs
---|---|---|---
K Steel| | | 8pcs
L Runner| | 14″| 2pcs
M JCBC Bolt| | M6x3Omm| 1 pc
N Corner Block| | | 12pcs
0 Allen Key| | M4| 1pc
STEP 1
****
- For Center Panel Use
- For Drawer panel Use
STEP2
STEP3
STEP4
STEP5
**STEP6
**
STEP7
STEP8
**STEP9
**
**STEP10
**
STEP11
STEP12
STEP13
STEP14
STEP15
STEP16
STEP17
STEP18
**STEP19
**
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting. Use of
furniture polish is not necessary. Should you choose to use polish, test first
in an inconspicuous area. Using solvents of any kind on your furniture may
damage the finish. Never use water to clean your furniture as it may cause
damage to the finish.
Liquid spills should be removed immediately. Using a soft clean cloth, blot
the spill gently. Avoid rubbing. Check bolts/screws periodically and tighten
them if necessary
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme
temperature and humidity changes can cause fading, warping, shrinking and
splitting of wood.
It is advised to keep furniture away from direct sunlight as sun may damage
the finish.
Proper care and cleaning at home will extend the life of your purchase.
Following these important and helpful tips will enhance your furniture as it
ages.