eta 108890000 Electric Hand Mixer Instruction Manual

108890000 Electric Hand Mixer
Instruction Manual eta 1088, eta 2088, eta 3088,

|
---|---

SAFETY WARNINGS

• Before the first use, read the instructions for use carefully, look at the picture and store the instructions for use in the future. Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.

• Check whether the data on the type label corresponds with the voltage in your socket. The power cord plug has to be connected to the properly connected and grounded
  socket according.

• Do not insert or take out the plug to or from a socket with wet hands and do not pull the power cord!

• Do not leave the appliance running unattended and check it during the food preparation!

• The product is intended for home use and similar (in shops, offices, and similar workplaces, in hotels, motels, and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!

• This appliance must not be used by children. Keep the device and its supply cord out of reach of children. The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under supervision or they have been instructed about using the appliance safely and understand the potential dangers. Children must not play with the appliance.

• If the power cord of the appliance is corrupted, it has to be replaced by the producer, its service technician, or a similarly qualified person so as to prevent dangerous situations.

• Be careful when handling the accessories (immersion blender), the knife is very sharp!

• Be careful when pouring hot liquid into the food processing device or the mixer because it may spurt out of the appliance because of the sudden boil.

• Always unplug the appliance from the power supply if you leave it unattended and before assembly, disassembly or cleaning.
  Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!

• Never use the appliance if its power cord or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell into the water. In this case, take the appliance to a special service to check its safety and proper function.

• Use the appliance in the working position only at places with no risk of turning over and in a sufficient distance from heat sources (e. g. heater, stove, grill, etc.), and wet surfaces (e. g. sinks, wash basins, etc.)

• Use the appliance designed for this type only. Using another appliance can represent a risk for the operator.

• Do not switch on the appliance without ingredients in it!

• Do not mix attachments (whisks E and hooks F). If there are accessories in the propulsion unit (E or F), you can not connect blender G at the same time and vice versa.

• Do not insert the accessories in any bodily orifices.

• If the propulsion unit is operating, do not remove the accessories (e.g. whisks, hooks,  blender), bowl, lid, and do not fold out the bracket of the stand!

• Make sure the supply cord does not get between the rotating parts of the accessories.

• Working attachments can not be replaced during the operation of the propulsion unit due to safety.

• Check if switch A1 is in position 0 (off) before each plugging in of the appliance and unplug the appliance after finishing work.

• Turn the device off and unplug from the power source by pulling the plug out of the socket before replacing any attachments or accessible parts which are moving during operation (before installing or uninstalling, before cleaning or maintenance).

• Always unplug the appliance from the power source when left unattended.

• Do not let children use the appliance without supervision!

• Do not process ingredients with a temperature higher than approx. 80 °C.

• Never insert e.g. fingers, fork, knife, spatula, or spoon into rotating parts of the appliance and the accessories.

• If the processed ingredients begin to stick on the accessories (e.g. whisks kneading hooks, blender knife), lid or container, turn the appliance off and clean the accessories
  carefully with a spatula L.

• Make sure the whisks do not hit the walls of the utensils during operation or do not get stuck in the thick matter or frozen ingredients.

• Check the condition of the supply cord regularly.

• Prevent the supply cord to hang loosely over the edge of the working desk where children could reach it.

• The power cord must not be damaged by sharp or hot objects, or open fire, it must not be sunk into water or bent over sharp edges.

• If you need to use the extension cord, it has to be uncorrupted and it has to comply with the valid standards.

• When storing, do not place any objects on the surface of the scale, it could be damaged.

• If you are not going to use the scale for a longer period of time, remove the batteries from the stand.

• If the batteries are leaking, replace them immediately.

• Dispose of the old batteries appropriately (see paragraph VII. ECOLOGY).

• Never use the appliance for any other purpose than for that described in these instructions for use!

• The producer does not undertake any responsibility for damage caused by improper use of the appliance and the accessories (e.g. food deterioration, injury by knife-edge, fire, etc.) and its guarantee does not cover the appliance in the case of failure to comply with the safety warning above.

FEATURES OF THE DEVICE AND ACCESSORIES (pic. 1)

The basic version of the ETA 1088 mixer comprises of the propulsion unit, whisks, kneading hooks, immersion blender, mixing utensil, spatula, and side rack for accessories. The  ETA  2088 and ETA 3088 version is equipped with a light and is extended by a stand with a rotary bowl and a lid. The ETA 3088 has a scale built into the stand.

A – propulsion unit
A1 – speed selector
A2 – TURBO button
A3 – release button
A4 – openings to connect accessories (E, F)
A5 – integrated light
A6 – sliding cover of the blender drive
A7 – foldable stand/holder
A8– supply cord| B – stand
B1 – fold-out bracket
B2 – bracket fastener button
B3 – mixer fastener button
B4 – fastening segment for a spatula
B5 – inbuilt scale control panel
---|---
C – lid
C1 – feeding opening lid
D – rotary bowl
E – whisks
F – kneading hooks| G – an immersion blender
H – mixing utensils
I – antiskid pad/lid
J – removable special spatula
K – side rack
L – spatula

PREPARATION FOR USE (pic. 1, 2)

Remove all packaging material and remove the mixer with accessories. Remove all adhesive foils, stickers or paper from the appliance. Wash all parts which will come in touch  with food in hot water with soap, rinse them thoroughly with clean water and wipe dry or let dry before first use.
Use of the individual levels (A1, A2)

0 – off
1 to 4 – speed selection (use for whisking, mixing, kneading)
– position of the switch only for mixing (turn the submersible blender on by pressing the TURBO button)
TURBO button – the motor is running at max. power the whole time the button A2 is pressed  – may be use at any speed level except 0.

Stand (B) – for ETA 2088 and 3088
Folding out the bracket – press the B2 button and fold out the bracket B1. To fold the bracket back press the B2 button again. The bracket will fold back and fasten (an audible click will sound).
Rotary bowl (D) – for ETA 2088 and 3088
Inserting the bowl into a stand – fold out the B1 bracket and place the bowl into stand B so that the protrusions on the bowl fit into the protrusions on the stand along the whole rim. Proceed reversely when removing the container.
Removable spatula (J) – for ETA 2088 and 308 8
It is intended for wiping the ingredients from the walls of the bowl and guiding toward the rotary accessories. Thus all the ingredients will be thoroughly mixed. We recommend using the spatula when processing thin mixtures. Slide the spatula all the way in the fastening segment opening B4 on the bottom part of bracket B1 (pic. 3).  Proceed reversely when removing the container.
Inserting and removing the lid (C) – for ETA 2088 and 3088
Insert the lid in bracket B1 so that the protrusions on the lid fit in the grooves in the bracket. Push the lid then all the way. Proceed reversely when removing the container.
Feeding opening cover (C1) – for ETA 2088 and 3088
Sliding the cover aside, the feeding opening can be used to add liquid or solid ingredients in bowl D when the propulsion unit A is running.

USE OF THE ACCESSORY (pic. 1, 2, 3)

Consider the following tips for processing examples and inspiration whose purpose is not to provide instructions but to show the various options of food processing.  Preparation (processing) times of ingredients range within minutes.
Select the number of processed ingredients so that the maximum content of the mixing utensil H (marked by a line MAX) and of the rotary bowl D (2 l) for liquids is not exceeded.
Bigger amounts of ingredients must be divided into several portions and the content of the utensils must be checked regularly. We recommend stopping the working, turning off the appliance (position 0), and removing all ingredients which have stuck on the accessories E, F, G, or the walls of the utensils and lid (see I. SAFETY PRECAUTIONS).
Turn off the mixer A and unplug the fork of the supply cord A8 from the el. outlet after finishing work. Utensil H and bowl D are suitable for use in a microwave oven.
Whisks (E)
Use: whisking egg whites, mousse, creams, whipped cream, sponge cake/whipped pastry, puree, etc. speed level 1 – 4, time of whisking approx. 1 – 5 minutes We recommend using the mixing utensil H or another suitable slender utensil.
Never use the whisks for mixing solid matters, e.g. leavened dough.
Inserting: mutual position is designated by their construction, it is therefore impossible to switch the whisks in the openings. Insert the whisks all the way in respective openings  A4 in the bottom part of the propulsion unit. Release the whisks by pressing the release button A3.

Kneading hooks (F)
Use: spread processing, mashing potatoes, spinach, mixing dough, etc. speed level 1 – 4, time of mixing approx. 1 – 5 minutes. We recommend putting loose ingredients in the bowl first and then adding the liquid ingredients when processing tough dough for better mixing.
Inserting: mutual position is designated by their construction, it is therefore impossible to switch the hooks in the openings. Insert the hooks in respective openings A4 in the bottom part of the propulsion unit. Release the hooks by pressing the release button A3.

Notice
Turn the appliance on only when the accessories E, F, and G are immersed in the ingredients processed. Let the propulsion unit cool off for approx. 15 minutes after 10 minutes of continuous operation. The hooks and whisks can be released from the propulsion unit only when the speed selector A1 is in position 0.

An immersion blender (G)
Use: blending and mixing all kinds of liquids, mayonnaise, dietary and baby food, etc., in a blending utensil H or another suitable utensil. selector level  TURBO button, blending time approx. 30 – 60 seconds
Inserting: insert the cover A6, and screw the blender G in the opening in the propulsion unit A.
Proceed reversely when removed from the propulsion unit.

Stand with a rotary bowl (B, D) – for ETA 2088 and 3088
Use: for whisking and mixing without having to hold the propulsion unit in hand.
Inserting: place stand B on a suitable working surface (see I. SAFETY PRECAUTIONS). Fasten the desired accessory E into the propulsion unit A or F. Put the mixer A on the bracket B1 so that the toothing on the accessory fits in the toothing in the bracket and then push the mixer all the way till it fits closely into the depression in the bracket  (you will hear an audible click). Fold-out bracket B1. In case of processing a thin mixture, connect a special bowl spatula J. Slide the lid C on the bracket. Place bowl D with the ingredients on the stand. Fold the bracket back only after its arrest has been clicked in.
Removing the propulsion unit (A) – by pressing button B3, the arrest will be released and it is then possible to remove propulsion unit A from the fold-out bracket B1.
Light (A5) – for ETA 2088 and 3088
The light is on when the propulsion unit is operating. It serves to give you better control over the food processing in the rotary bowl.
Stand/holder (A7)
It serves to put away the mixer or to hang it when storing (when folded out) (pic. 5).
Side rack (K)
The stand serves for space-saving storage of accessories.

USING THE BUILT-IN SCALE – for ETA 3088

The scale is intended for weighing ingredients in the rotary bowl D. Weigh the ingredients only when bracket B1 is folded out.

Control panel
display – shows the weight measured, symbols of functions of the scale, and error messages
ON/OFF button – to turn the scale on/off
TARE button – to reset the scale and to set zero values

Inserting batteries
Open the battery cover on the bottom part of stand B, insert 2 pcs of AA batteries observe the +/- signs and replace the cover.

Weighing

1. Fold out the bracket B1 and put the rotary bowl D into stand B.
   Do not put any ingredients which you want to weigh in the bowl before turning it on!

2. Turn the scale on by pressing the ON/OFF button on the control panel B5 (display shows all symbols for approx. 2 seconds).

3. When the display shows 0 g, the scale is ready to weigh.

4. Put the prepared ingredient in the bowl and wait till the value on the display stabilizes.
   During stabilizing the left part of the display shows HOLD.

5. You can turn the scale off either by pressing the ON/OFF button or the scale will turn off automatically after 1 minute.

TARE function
You may use this function to set zero value when weighing (adding various ingredients).
Press the TARE button to reset the display before adding each ingredient. When the display shows 0 g, the scale is ready for the next measuring.
Notes
If you remove the bowl with the weighed ingredient after resetting with the TARE button, the display will show a negative value. If the scale turns off between individual ingredients  (due to no activity) and you wish to add/weigh other ingredients, proceed as follows before turning it on again. First, lift the bowl with the ingredient from the stand and press the ON/OFF button to turn it on. After the display shows 0 g, put the bowl back on the stand and press the TARE button, reset the value on display for further weighing.
Exceeding the scale range
The maximum amount that can be weighed is 3000 g. If you weigh an item heavier than 3000 g, the display will show error EEEE. This means that the weight of the measured item exceeds the scale‘s range.

Attention: Ingredients of excessive weight must be removed from the scale to avoid damage of the scale.
Error messages are shown on the display
Battery symbol – low batteries, remove batteries
EEEE– overload, the weight exceeds 3000 g
– – – – unstable zero position

MAINTENANCE

Turn the appliance off and unplug the fork of the supply cord after finishing work and before each maintenance! Do not use rough and abrasive cleaning agents (e.g.  sharp objects, scrapers, diluents or other dissolvents)! To clean the propulsion unit A and stand B use a soft damp cloth with soap. Make sure that water does not get to the inner parts.  Wash another accessory immediately after use in hot water with soap, rinse with clean water and wipe dry (you may use the dishwasher – not for the blender G). The end with the thread of the blender G must not be immersed during cleaning (pic. 6). Work very carefully when cleaning the blender, the knife is very sharp! Make sure that the cutting edges of the blender do not come in touch with hard objects that blunt them and thus decrease their effectiveness.
Some foods may discolor the accessory. This has, however, no effect on the functions of the appliance and is no reason to take the appliance back. This discoloration usually disappears with time. Never dry the plastic die-cast over a heat source (e.g. stove, cooker, radiator).

Storing the appliance and accessory
Wind the supply cord A8 over the rear part of the propulsion unit A and secure it with a clasp after cleaning (pic. 7). Store the propulsion unit in a dry, dustless place, out of reach of children and persons sui juris.
Store accessories E, F, G, and H in rack K (pic. 8). Secure the submersible blender G in the rack by turning it at 45 °.

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for the production of packing, components, and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal, hand them over at the special collection places where they will be accepted free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authority or at a collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. If the appliance is to be put out of operation, after disconnecting it from the power supply we recommend its cutoff, and in this way, it will not be possible to use the appliance again. Remove the  dead batteries from the rack (for ETA 3088) and dispose of them by the means of collection networks intended for this purpose. Never dispose of the batteries by burning them!

More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service! Failure to comply with the instructions of the manufacturer will lead to the expiration of the right to guarantee repair!

TECHNICAL DATA

The product has received ES declaration of conformity according to Act as amended. The product matches the requirements of the below statutory order asamended:

• Committee Regulation No. 2006/95/ES as amended, setting the technical requirements of the electrical appliance as low.
• Committee Regulation No. 2004/108/ES as amended, setting the technical requirements of products in terms of their electromagnetic compatibility.

The product is in conformity with the European Parliament and European Committee Regulation No. 1935/2004/ES re. Materials and objects designed for contact with food.  The manufacturer reserves the right for any insignificant deviations from the standard finished product that do not have any effect on the functioning of the product.

HOUSEHOLD USE ONLY.
DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.
TO AVOID THE DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS,  CARRIAGES, OR PLAYPENS. THIS BAG IS NOT A TOY.

PRODUCER: ETA a.s., Zelený pruh 95/97, 147 00 Praha 4-Bráník,
Czech Republic.

References

• ElektroEko – Odbiór odpadów elektro
• Úvod | ELEKTROWIN, a.s.
• Úvod - Envidom
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>