Hatari AC Pro Portable Air Cooling Fan User Manual
- June 5, 2024
- Hatari
Table of Contents
Hatari AC Pro Portable Air Cooling Fan User Manual
FAN COMPONENTS
-
CORD WINDER
-
CONTROL AND DISPLAY PANEL
-
HANDLE
-
WIND DIRECTION SHUTTERS
-
FRONT COVER
-
WATER TANK
-
WATER LEVEL WINDOW
-
WHEELS (2 back wheels with brakes)
-
PRE-FILTERS
♦ SIDE 2 PIECES
♦ BACK 2 PIECES -
SIDE GRILLES (LEFT-RIGHT)
-
BACK GRILLE
-
WATER DIFFUSING PLATE
♦ SIDE 2 PIECES
♦ BACK 1 PIECE -
POWER SUPPLY CORD WITH PLUG
-
TOP COVER
-
WATER DRAIN LID
-
REMOTE CONTROL
-
GEL PACK 2 PIECES
-
SPACE FOR REMOTE CONTROL
WHEELS INSTALLATION
Make sure that the water tank is empty and that the power supply cord is not plugged in. On a flat surface, place the air cooler on its side and push the wheels into the indicated positions. Install the 2 wheels with brakes at the back and the other two at the front of the machine.
CORD WINDER INSTALLATION
Place the cord winder behind the machine above the water tank, ensuring the screw holes align according to the diagram. Tighten the 2 screws to mount the cord winder to the machine.
DIRECTION OF USE
This fan is operated by touch screen system and remote control. Touch screen system can be activated using fingers to touch the control and display panel. When the machine is left idle for 20 seconds, the operating lights will dim but the fan will still be operating as normal. By simply touching the control and display panel, the lights will illuminate and the fan will be ready to be adjusted again. Remote control , point the remote signal transmitter in the direction of the signal receiver on the control and display panel. Avoid having obstructions between the remote signal transmitter and the receiver.
Plug the power supply cord into a 220V, 50Hz power socket.
-
ON/OFF Touch the switch on the control and display panel to turn on the fan. The light will show the resumed settings of the fan’s latest operation before having been switched off. To turn the fan off, touch the switch again for about 1.5 seconds.
-
SPEED 5 adjustable fan speed settings 0: off,1: lowest speed, 2: low speed, 3: medium speed, 4: high speed, 5: highest speed, respectively.
-
TIMER Switch for timing the fan’s operation: 1, 2, 4, 8 hours or to cancel timing altogether, respective to the number of time the sensor is touched. Once set, the timer will indicate the remaining time left of the duration.
3.1 TIMER OFF Set the timer while the fan is switched on to set the time when the fan is to automatically turn off.
3.2 TIMER ON Set the timer while the fan is turned off (but it must be plugged in) to set the time when the fan is to automatically turn on. After adjusting the settings, the operating lights will dim. When the time comes, the fan will resume settings of the latest operation before having been switched off. -
COOL Switch for activating the water cooling system. Touch the switch to activate the function. Touch the switch again to deactivate the function.
-
SWING Switch for adjusting left to right swinging motions. Touch the switch to activate the function. Touch the switch again to deactivate the function.
-
AMBIENT LIGHT Ambient light on/off switch. Touch the switch to turn on the light. Touch the switch again to turn off the light.
-
AMBIENT LIGHT COLOR Switch for changing the color of the ambient light. Touch the switch to change the color (White – Blue – Pink – Green) respectively. To use this function, the ambient light has to be turned on. (This function can be controlled on the control and display panel only)
-
BRIGHTNESS CONTROL Switch for adjusting the brightness of the ambient light. Can adjust the brightness in 3 levels (High brightness – Medium brightness – Low brightness).
-
FILL WATER A warning will light up when the water level in the tank is too low for the water distribution system to function (unable to activate COOL function). Turn off and unplug the machine to fill the water tank with clean water (do notexceed MAX level). The warning light will go off when the machine is turned on and the COOL function is activated.
-
ELCB A warning with a warning sound will appear when there is electricity leakage. The circuit breaker system will immediately be activated.
-
DRYING Drying light will light up when the fan is switched off while the COOL function is activated, the fan will continue to operate for 60 seconds to remove moisture. The temperature display will show a countdown of 60 seconds, after which the fan will stop automatically.
-
TEMPERATURE Temperature display for the surrounding area of the fan while the fan is turned off or on (but it must be plugged in)
HOW TO REPLACE THE REMOTE CONTROL BATTERY
Open the battery cover by using your fingernail to push the catch downwards as shown by the arrow and remove the battery cover. Replace the used batteries with new “AAA” batteries, ensuring that the positive (+) and negative (-) poles are correctly inserted and correspond with the symbols on the remote control. Place the battery cover back in its original position.
*Batteries should be removed from the remote control when not in use for a long period of time.
CAUTION
- Unplug the power supply cord before filling water, cleaning or changing the components, and when not in use for a long period of time
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experiences and knowledge, unless they have been given supervision or instruction concerning use of the appliance.
- Children should be supervised to ensure they do not play with the appliance.
CARE AND CLEANING INSTRUCTIONS
- Use a damp cloth to wipe stains, and then dry the area by wiping.
- When cleaning, be careful not to let the supply cord, switch, motor, and other electrical components get wet.
- Do not use chemical products, thinner solvents, alcohol, kerosene or petrol to clean the fan.
- The water tank, pre-filter, grilles, and water tank can be cleaned with water or soapy water. It should be cleaned at least every 1-2 months.
Remove the side grille (left & right)
Remove carefully the grille by using a cross slot screwdriver to loosen the screws. The press the locks (top and bottom) with your fingers to remove the side-grille (left and right side). Now remove the pre-filter by lifting the 2 snap-hooks then slid out the pre-filter.
Remove the back grille
Remove carefully the grille by using a cross slot screwdriver to loosen the screws. Then press the locks (top & bottom, left & right) with your fingers to remove the back-grille. Now remove the pre-filter by lifting the 2 snap-hooks then slid out the pre-filter.
Cleaning the pre-filters (4 pre-filter)
To remove the pre-filter, the grilles (left, right & back) need to be removed. Tap the pre-filter with water for cleaning. If the filter is really dirty, dip it into natural detergent solution to wash and flush with water. Let it dry naturally.
USAGE RECOMMENDATIONS
- The fan should not be placed or installed in areas that are of extreme temperatures or near stoves, or in areas that are wet with high humidity, or has hydrocarbon vapors such as petroleum.
- Do not spray all types of spray into the fan; for example, hairspray or cleaning spray.
- Do not insert fingers, pencils or other objects into the grille while the blades are spinning as it may result in possible injury or physical damage.
- If an electrical component such as supply cord, motor, or switch is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. It is not advisable to fix the fan at home.
- The fan must always be placed vertically; it must never be lying horizontally or placed upside down. If the fan falls down, unplug it immediately and lift the fan up to a vertical standing position. Use a cloth to wipe the fan and leave it to dry in order to prevent electrocution.
USAGE PRECAUTIONS
Use only clean water to fill the water tank. Do not use any other liquid. The water tank should be cleaned regularly to reduce bacteria buildup.
Pull open the water tank lid to fill water before inserting the gel pack (frozen).
Constantly check the water level in the tank, making sure that it is not below the MIN level and not above the MAX level.
If the fan is not in use for a long period of time, drain out all the water by twisting open the water drain lid. Securely close the lid back after to prevent dust and insects from entering the water tank.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>