Hatari HT-AC10R2 Air Cooler with Remote Control User Manual
- June 9, 2024
- Hatari
Table of Contents
Hatari HT-AC10R2 Air Cooler with Remote Control User Manual
FAN COMPONENTS
- CONTROL AND DISPLAY PANEL
- WIND DIRECTION SHUTTERS
- FRONT COVER
- WATER TANK
- WATER LEVEL WINDOW
- WHEELS (2 back wheels with brakes)
- BACK COVER
- WATER DIFFUSING PLATE
- PRE-FILTER
- CORD WINDER
- POWER SUPPLY CORD WITH PLUG
- REMOTE CONTROL
- GEL PACK 2 PIECES
DIRECTION OF USE
This fan is operated by touch screen system and remote control. Touch screen system can be activated using fingers to touch the control and display panel. When the machine is left idle for 1 minute, the operating lights will dim but the fan will still be operating as normal. By simply touching the control and display panel, the lights will illuminate and the fan will be ready to be adjusted again. Remote control , point the remote signal transmitter in the direction of the signal receiver on the control and display panel. Avoid having obstructions between the remote signal transmitter and the receiver.
Plug the power supply cord into a 220V, 50Hz power socket.
-
ON/OFF – Touch the switch on the control and display panel to turn on the fan. The light will show the resumed settings of the fan’s latest operation before having been switched off. To turn the fan off, touch the switch again for about 1.5 seconds ( When the air cooler is switched off while the COOL function is activated, the fan will continue to operate for 1 minute to remove moisture. The fan will stop working immediately afterwards )
-
SPEED – 4 adjustable fan speed settings 0: off, 1: lowest speed, 2: medium speed, 3: high speed, 4: highest speed.
-
TIMER – Switch for timing the fan’s operation: 1, 2, 4, 8 hours or to cancel timing altogether, respective to the number of time the sensor is touched. Once set, the timer will indicate the remaining time left of the duration.
3.1 TIMER OFF – Set the timer while the fan is switched on to set the time when the fan is to automatically turn off.
3.2 TIMER ON – Set the timer while the fan is turned off (but it must be plugged in) to set the time when the fan is to automatically turn on.
After adjusting the settings, the operating lights will dim. When the time comes, the fan will resume settings of the latest operation before having been switched off. -
COOL – Switch for activating the water cooling system. Touch the switch to activate the function. Touch the switch again to deactivate the function.
-
SWING – Switch for adjusting left to right swinging motions. Touch the switch to activate the function. Touch the switch again to deactivate the function.
-
IONIZER – Switch for activating the Ionize system. Touch the switch to activate the function, the light will illuminate indicating the operation of the Ionize system. Touch the switch again to deactivate the function.
-
AUTO – Switch for activating the automatic control system. Touch the switch to activate the function, which will work simultaneously with the water cooling system (COOL) to control the air cooler’s operation, resulting in appropriate water usage. This is so that the water cooling system can operate for longer without having to frequently refill the water. Touch the switch again to deactivate the function.
-
ELCB – A warning with a warning sound will appear when there is electricity leakage. The circuit breaker system will immediately be activated.
HOW TO REPLACE THE REMOTE CONTROL BATTERY
Open the battery cover by using your fingernail to push the catch downwards as shown by the arrow and remove the battery cover. Replace the used batteries with new “AAA” batteries, ensuring that the positive (+) and negative (-) poles are correctly inserted and correspond with the symbols on the remote control. Place the battery cover back in its original position.
*Batteries should be removed from the remote control when not in use for a long period of time.
CAUTION
- Unplug the power supply cord before filling water, cleaning or changing the components, and when not in use for a long period of time.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experiences and knowledge, unless they have been given supervision or instruction concerning use of the appliance.
- Children should be supervised to ensure they do not play with the appliance.
CARE AND CLEANING INSTRUCTIONS
- Use a damp cloth to wipe stains, and then dry the area by wiping.
- When cleaning, be careful not to let the supply cord, switch, motor, and other electrical components get wet.
- Do not use chemical products, thinner solvents, alcohol, kerosene or petrol to clean the fan.
- The water tank, pre-filter, grilles, and water tank can be cleaned with water or soapy water. It should be cleaned at least every 1-2 months.
USAGE RECOMMENDATIONS
- The fan should not be placed or installed in areas that are of extreme temperatures or near stoves, or in areas that are wet with high humidity, or has hydrocarbon vapors such as petroleum.
- Do not spray all types of spray into the fan; for example, hairspray or cleaning spray.
- Do not insert fingers, pencils or other objects into the grille while the blades are spinning as it may result in possible injury or physical damage.
- If an electrical component such as supply cord, motor, or switch is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. It is not advisable to fix the fan at home.
- The air cooler must always be placed vertically; it must never be lying horizontally or placed upside down. If the air cooler falls down, unplug it immediately and lift the fan up to a vertical standing position. Use a cloth to wipe the air cooler and leave it to dry in order to prevent electrocution.
USAGE PRECAUTIONS
Use only clean water to fill the water tank. Do not use any other liquid. The water tank should be cleaned regularly to reduce bacteria buildup.
To prevent water pump damage, ensure that the water pump is in the locked position (folded up) and that it is not obstructing the water tank before inserting the water tank into the machine.
Insert the gel pack (frozen) into the right side of the water tank to prevent water pump damage.
To pull out the water tank, insert your fingers into the groove under the water tank and pull it out.
Constantly check the water level in the tank, making sure that it is not below the MIN level and not above the MAX level.
Wind the power supply cord around the cord winder before maneuvering the machine and when not in use for a long period of time.