CARTONI Master 6S Flat Base Adapter and Pump User Manual

ARTONI Master 6S Flat Base Adapter and Pump

INTRODUCTION

Designed to support Camera weights from 20 Kg (44 lbs) to 65 Kg (143 lbs), the new MASTER 65 is ideal for outdoor Broadcast with bulky boxed lenses. Depending on the Center of Gravity (CG) position, the maximum payload is:

• At 200 mm: 65 kg
• At 175 mm: 70 kg
• At 150 mm: 80 kg

It combines a wide range of counterbalance capabilities, performing perfect balance at any tilt angle with a new CARTONI Fluid drag system based on silicon lubricated friction. The new drag ensures almost free-wheeling at its minimum, up to a consistent drag for smooth and slow movements with long focal lengths. This rugged Head comes equipped with the standard Dovetail plate on a large sliding platform. The micrometric movements of the slide are operated by a handy crank placed under the slide plate. All settings are ergonomic and placed in the right positions. Pan Bars are compatible with the Vinten attachment. MASTER 65 comes equipped with a digital readout for counterbalance reference and illuminated bubble level. The MASTER 65 flat base interfaces with Mitchel mount Tripods, Pedestals, and other supports via 4 bolts fixing system, 2 ¾” castle-nut, or an M12 threaded central knob.

• Before using the MASTER 65 Fluid Head, please make sure to read this user’s & maintenance manual;
• Before installing the Fluid Head on the Tripod check the Tripod stability;
• Check that the Camera payload (including lenses and accessories) is lower than the maximum capacity of the MASTER 65 Fluid Head;
• Before installing the Camera make sure that the MASTER 65 is in good condition and bears no evident damages.

OPERATING ELEMENTS

1. Camera plate
2. Right handle attachment
3. Right handle
4. Right handle attachment lever
5. Camera plate lock lever
6. Battery housing
7. Transport handle
8. Horizontal lock button (On)
9. Horizontal lock button (Off)
10. Tilt lock lever
11. Pan lock lever
12. Tie-down knob
13. Sliding plate lock lever
14. Left panhandle attachment
15. Left panhandle attachment lever
16. Sliding plate crank
17. Left extensible handle
18. Pan drag selector
19. Counterbalance selector
20. Digital display
21. Illuminated bubble level and display light button
22. Illuminated bubble level
23. Tilt drag selector

PROCEDURES

• Open the Tripod to the desired height and lock all safety knobs.
• Place the MASTER 65 Fluid Head on the Tripod base and rotate until it matches the steel notch; tighten the Head firmly by screwing in the knob (12) underneath the flat base. Check the illuminated bubble level (22) and modify the legs angle if needed. In case of low visibility, press button (21) for illuminated bubble level and to activate the digital displays. Lights will turn off automatically after approximately 30 seconds.
• Lock the horizontal position with a button (8), insert pan lock (11) and turn both tilt drag selector (23) and counterbalance selector (19) to position “0”.
• To release the Camera plate (1) slide forward the Camera plate lock lever (5) and rotate it 90° counterclockwise, then remove the Camera plate.
• Attach the Camera plate under the Camera assembly and firmly secure it with both screws. Try to place the Camera plate centered under the Camera system, keeping in mind the position of the center of gravity (CG).
• Place the Camera on the top of the MASTER 65, by pushing the Camera plate (1) forward to perfectly match the sliding plate’s proper position, then close the Camera plate lock lever (5).
• Holding the pan bar (17) firmly, disengage the horizontal lock with a button (9) and find the correct center of gravity (CG) by sliding the Camera assembly fore-and-aft using the sliding crank (16) (extract the knob to rotate). Lock the sliding plate with a lever (13).
• Set the counterbalance system by turning the counterbalance selector (19) to the appropriate tension. The Camera has to stay still at any tilt angle. If needed, fine-tune the balance by adjusting the sliding plate.
• Push-button (21) to activate illuminated digital displays (20), unlock Pan lock (11), and select the desired Fluid drag intensity on both Pan and tilt by turning Pan selector (18) and tilt selector (23).

SPECIFICATIONS

MAINTENANCE

When needed, with indoor use just clean the Head and Tripod with a soft cloth. Dirt accumulated during storage may be removed using a brush or Air spray.
CARTONI product’s main mechanisms are sealed as they are also built for professional outdoor use.
However, use under rough conditions they will require special care. Saltwater is very corrosive and can cause extreme damage. In an attempt to avoid further damage, the Fluid Head should be washed off with fresh water at the earliest opportunity and perfectly dried before storage. Sand and dirt are abrasive and should be removed using a semi-stiff brush or Air spray. Disconnect the illuminated display & bubble level battery during long-term storage; for battery replacement access the battery compartment (6).

WARRANTY

All CARTONI Fluid Heads & Pedestals have a free of charge three (3) year warranty. Register your product at www.cartoni.com within 30 days from date of first purchase/invoice to receive further two (2) year warranty for the unsurpassed free five (5) year warranty. Tripods, spreaders, dollies and all accessories are guaranteed one (1) year from the date of first purchase/invoice.
CARTONI warrant that the product supplied will – under proper use – be free from defects in workmanship and materials and agrees that it will, at its option, either repair or replace any defective part within duration of warranty from date of first purchase with no labour charge. This warranty does not apply to any CARTONI product that has been damaged in shipping or handling, abused, misused, operated contrary to instructions for use, neglected, normal wear or tear, modified or changed in design or construction or serviced by unauthorized parties. Repairs or misuse by any unauthorized parties will void this warranty. Warranty claims must be submitted – in writing – to the factory for verification or to an authorized distributor/dealer designated by CARTONI. It is the end user’s responsibility when ordering to ensure that the products ordered conform to his requirements. All freight of product to CARTONI must be prepaid. All implied warranties are limited to the time period set forth herein & subject to change without notice.

ACCESSORIES & PRODUCT LINE

For the complete Accessories list & Product line please visit CARTONI’s official website www.cartoni.com. Every product has an updated list of compatible items sorted by groups, with descriptions and technical data.

PROFESSIONAL CAMERA SUPPORT
CARTONI S.p.A
Via di Portonaccio, 33/B – 00159 Rome (Italy) Phone +39 06 4382002 Fax +39 06 43588293
Email: cartoni@cartoni.com www.cartoni.com

References

• Cartoni | Professional Camera Supports

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>