eta 2015 90020 Spesso Electric Stick Mixer with Accessories Instruction Manual

eta 2015 90020 Spesso Electric Stick Mixer with Accessories

INSTRUCTIONS FOR USE

SAFETY WARNING

• Before the first use, read the instructions for use carefully, look at the picture and store the instructions for use for the future. Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
• Check whether the data on the type label correspond with the voltage in your socket. The power cord plug has to be connected to the properly connected and grounded socket according.
• Never use the appliance if its power cord or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell to water. In this case take the appliance to a special service to check its safety and proper function.
• Do not insert or take out the plug to or from a socket with wet hands and do not pull the power cord!
• This appliance must not be used by children. Keep the device and its supply cord out of reach of children. The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under supervision or they have been instructed about using the appliance safely and understand the potential dangers. Children must not play with the appliance.
• Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!
• If the power cord of the appliance is corrupted, it has to be replaced by the producer, its service technician or a similarly qualified person so as to prevent dangerous situations.
• Be careful when handling the accessories (immersion blender), the knife is very sharp!
• Be careful when pouring hot liquid into the food processing device or the mixer because it may spurt out of the appliance because of sudden boil.
• In case you are going to process hot liquid (mixing a hot soup with vegetables etc.), be careful because it may spurt out of the container because of sudden boil.
• When handling the sickle-shaped knife, be very careful, especially when removing it from the chopping container, when emptying the container and while cleaning. The knife is very sharp!
• Do not use the appliance without the anti-slip base!
• Never immerse the drive unit into water or wash it in running water!
• The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!
• Use the appliance in the working position only at places with no risk of turning over and in sufficient distance from heat sources (e. g. heater, stove, grill, etc.), and wet surfaces (e. g. sinks, wash basins, etc.)
• Use the appliance designed for this type only. Using another appliance can represent a risk for the operator.
• Do not insert the appliance into any body holes.
• Do not switch on the appliance without ingredients in it!
• Do not remove the appliance if the drive unit is in operation!
• Make sure that the power supply cable does not get between the rotating parts of the accessories.
• Before you remove the appliance or the drive unit from the container, let the rotating parts stop completely.
• Before emptying the chopping container, first remove the sickle-shaped knife.
• Always unplug the appliance from power supply if you leave it unattended.
• Do not process food at temperature exceeding about 80 °C.
• Never insert e.g. fingers, fork, knife, spatula, spoon into rotating parts of the appliance and the accessories.
• If the processed food starts to stick to the appliance (e.g. on knives, the beater, the container or the lid), switch off the appliance and clean the accessories carefully (e.g. using a spatula).
• Check the condition of the power cord of the appliance regularly.
• Make sure that the power cord does not hang over the edge of the working table where children could reach it.
• Do not wind the power cord around the appliance; this will extend its life.
• The power cord must not be damaged with sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges.
•  If you need to use the extension cord, it has to be uncorrupted and it has to comply with the valid standards.
• Never use the appliance for any other purpose than for that described in these instructions for use!
• The producer does not undertake any responsibility for damage caused by improper use of the appliance and the accessories (e.g. food deterioration, injury by knife edge, fire, etc.) and its guarantee does not cover the appliance in the case of failure to comply with the safety warning above.

DESCRIPTION OF THE APPLIANCE

• A – drive unit
  • A1 – speed switch
  • A2 – speed regulator
  • A3 – adapters blocking buttons
  • A4 – power cord
• B – immersion mixer
• C – beater (only for type ETA 2015 and ETA 3015)
  • C1 – gear
• D – mixing/beating container (only for type ETA 2015 and ETA 3015 )
  • D1 – anti-slip base/lid
• E – chopping container (only for type ETA 3015)
  • E1 – central shaft
  • E2 – sickle-shaped knife
  • E3 – container lid
  • E4 – anti-slip base
• F – wall holder (only for type ETA 2015 and ETA 3015 )

PREPARATION AND USE OF THE APPLIANCE AND ACCESSORIES

Remove all the packing material and take out the drive unit and the accessories. Remove all possible adhesion foils, stick-on labels or paper from the appliance. Before the first use, wash the parts that will be in contact with food in hot water with a detergent, rinse them thoroughly with clean water and wipe till dry, or let them dry.

Holder (F)
The holder is intended for space-saving storage of the appliance (Fig. 8). Mount the holder on the wall using the supplied dowels and screws. Make sure that there is no electric, telephone, plumbing fitting under the plaster at the place of mounting the holder.

Safety switch (A1), (Fig. 2)

• Button I – low speed
• Button II – maximum speed
  By pushing and holding the button you will start the appliance and by releasing the button you will switch off the appliance.

Speed regulator (A2), (Fig. 2)

• By turning the regulator from 1 to 5 you can continuously change the speed of the motor revolutions.

• You can regulate the revolutions only when you choose speed I.

• Please consider the following tips for preparing food as examples and inspiration,
  the purpose of which is not to provide instructions, but to show various possibilities of preparing food. The times of food processing are only approximate and they range from seconds to minutes. Choose the amount of the processed food so that the maximum volume of the containers marked with the gauge line is not exceeded. Bigger amount of processed food has to be divided into several doses and the volume of the containers has to be checked regularly.

• Any time you work with the appliance, do not forget to put the anti-slip base D/E under the mixing and chopping container D1/E4 (fig. 6).

• We recommend stopping work from time to time, switching off the appliance and removing possible food that was stuck onto the mixing/chopping adapter B/C, the sickle-shaped knife E2, the containers D/E or the lid E3 (see par. I. SAFETY WARNING).

• After finishing work, disconnect the appliance from power supply by taking the connector of the power cord A4 out of the electric socket. Containers D/E are suitable for use in a microwave oven.

• Immersion mixer (B)
  The mixer is intended for mixing and blending juices, milk shakes, milk, sauces, soups, mayonnaise, children‘s and dietary food, for making purée, etc. Be careful, knife edges are very sharp!

• You can use speed I or II for processing.
  The maximum time of processing is 1 minute. Then wait for 10 – 15 minutes, which is necessary for the drive unit to cool down.

• Insertion and removal
  Slide the immersion mixer onto the drive unit A and secure it by slight pushing till the blocking snaps in (Fig. 3).

• For removing the mixer, push the blocking button A3 and remove the adapter.

• Hold the stick mixer A with your hand and put the immersion mixer B into the container D or into another suitable container filled with food. By pushing the required button of the switch A1 you will start the drive unit. When working, move the mixer in the container to process the food thoroughly. After finishing work, switch off the drive unit, remove the mixer from the container and clean it.

• Recommendation

  • It is recommended to cut tough ingredients into small pieces. Do not process very hard materials (e.g. ice cubes, etc.). The knife would be blunt soon.
  • Hard ingredients (e.g. legumes, soya beans, etc.) should be soaked in water before processing.
  •  The longer you process the food with the mixer, the smoother the result will be.
  • In the case of liquids that create foam (e.g. milk), never fill in the container D up to the gauge mark „MAX“ to prevent overflowing.
  • If you are not satisfied with the result, switch off the appliance, mix the ingredients with spatula, take some part of the ingredients or add a little liquid.

• Beater (C, C1)
  The beater is intended for whisking eggs, egg whites, whipping cream, creams, puddings, runny dough and similar food. Do not use the beater for whisking tough dough!  You can use speed I or II for processing. The maximum time of processing is 2 minutes. Then wait for 10-15 minutes, which is necessary for the drive unit to cool down.

• Insertion and removal
  Insert the shaft of the beater C into the gear C1, then slide the gear on the drive unit A and secure it by slight pushing till the blocking snaps in (Fig. 4).

• For removing the beater, push the blocking button A3 and remove the beater.

• Hold the stick mixer A with your hand and put the beater C into the container D or into another suitable container filled with food.

• By pushing the required button of the switch A1 you will start the drive unit. When working, move the beater in the container to process the food thoroughly.

• After finishing work, switch off the drive unit, remove the beater from the container and clean it.

• Recommendation

  • When beating egg whites, use eggs at room temperature. If beating is not optimal, make sure that the beater is not greasy, or add a little lemon juice or salt.
  • Cool cream and whipping cream to at least 6 °C.

• Sickle-shaped knife (E2) and chopping container (E) The knife is intended for chopping, mixing, blending all kinds of tough food (e.g. fruit, vegetables, nuts, almonds, meat without bones, tendons and skin) or for preparing purée.

• Do not use the knife for processing any dough! Be careful, knife edges are very sharp!

• Use speed II for processing. The maximum time of processing is 1 minute. Then wait for 10 – 15 minutes, which is necessary for the drive unit to cool down.

• Hold knife E2 on the upper plastic part, remove a possible protective lid and slide the knife to the central shaft E1 inside the container E (Fig. 5). Put food into the container. Put the lid E3 on the container so that the lugs on its edge snap into the moulded holes in the container and secure the lid by clockwise movement (Fig. 5). Insert the drive unit A onto the lid E3 so that it is blocked in the lid. By pushing the button of the switch A1 you will start the drive unit. After you have finished, switch off the drive unit. To remove the drive, push the blocking button A3 and remove the drive unit. Remove the lid E3 by opposite movement, remove the knife and clean it.

• Recommendation

  • Before processing, cut bigger pieces of food into cubes of about 3 x 3 x 3 cm.
  • Never crush very hard ingredients with the sickle-shaped knife, such as coffee beans, nutmeg, ice cubes, etc.! The knife would be blunt soon.
  • Hard ingredients (e.g. legumes, soya beans, etc.) should be soaked in water before processing.
  • The longer you process the food, the smoother the result will be.
  • If you chop hard cheese or chocolate, work for a short time. It is because the ingredients are heated excessively by chopping, they become softer and they can become lumpy.

• Base/lid (D1)
  You can use the base/lid either as an anti-slip base, or it you slide it on the bottom of the container D or you can use it as a lid of the container, if you store food (e.g. in a fridge), fig. 6.

MAINTENANCE

Unplug the appliance from power supply by taking the connector of the power cord out of the socket before every maintenance! Do not use rough and aggressive detergents! Clean the drive unit A, the gear C1 and the lid E3 with a soft and wet cloth with a little detergent on it. Make sure that water does not get inside the appliance. Wash the other accessories right after use in hot water with a little detergent added, rinse it with clean water and wipe it till dry (you can also use a dishwasher – but not for the mixer B). The end piece with the shaft of the mixer B must not be immersed during cleaning (Fig. 7). Be very careful when cleaning the mixer B and the sickle-shaped knife E2, the knives are very sharp. Make sure that the cutting edges of the knives are not in contact with hard objects that make them blunt and thus they reduce their effectiveness.Some food can colour the accessories in some way. But this does not affect the function of the appliance and it is not a reason for a claim. This colouring usually disappears in some time. Never dry plastic moldings over a heat source (e. g. heater, stove, radiator).Store the appliance after cleaning at a dry, dustfree and safe place, out of reach of children and incapacitated people.

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal, hand them over at the special collection places where they will be accepted free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authority or at a collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. If the appliance is to be put out of operation, after disconnecting it from power supply we recommend its cutoff and in this way it will not be possible to use the appliance again

More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service! Failure to comply with the instructions of the manufacturer will lead to expiration of the right to guarantee repair!

TECHNICAL DATA

The product has received EC declaration of conformity according to Act as amended. The product matches the requirements of the below statutory order as amended.

• Committee Regulation No. 2006/95/EC as amended, setting the technical requirements of the electrical appliance as low.
• Committee Regulation No. 2004/108/EC as amended, setting the technical requirements of products in terms of their electromagnetic compatibility

The product is in conformity with the European Parliament and European Committee Regulation No. 1935/2004/EC re. Materials and objects designed for contact with food. The manufacturer reserves the right for any insignificant deviations from the standard finished product which do not have any effect on the functioning of the product.

HOUSEHOLD USE ONLY.
DO NOT IMMERSE IN WATER OR OTHER LIQUIDS. TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY

References

• ElektroEko – Odbiór odpadów elektro
• Úvod | ELEKTROWIN, a.s.
• Úvod - Envidom
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>