UTILITECH 204 1001 UT4 Magnetic Charging Vent Mount Instruction Manual
- June 5, 2024
- UtiliTech
Table of Contents
Magnetic Charging
Vent Mount
Instruction Manual
UTILITECH and logo designs are trademarks or registered trademarks of LF, LLC.
All Rights Reserved.
Item no: 5061445 Model# 204 1001 UT4
Questions, problems, missing parts?
Before returning to your retailer, call our customer service department at
866-994-4148,
8 a.m. -8 p.m., EST, Monday-Sunday. You could also contact us at
partsplus@lowes.com
Thank you for purchasing the Magnetic Charging Vent Mount. Please read these instructions before use.
Package Contents
- Magnetic Charging Vent Mount
- Type C to USB Charging Cable
- User Manual
Components at a Glance
Magnetic Charging Vent Mount:
- Charging Plate with Magnetic Charging Ring
- Adjuster Ring
- Ball Joint
- Clip Release Button
- Vent Clip
- Type C Input Port
Getting Started ASSEMBLING MOUNT
- Remove the charging plate and vent dip with the adjuster ring from the paging.
- Make sure the adjuster ring is on the ball of the vent clip. Align the ball with the attachment point on the back of the charging plate and push until it clicks into place. (If the ball is unable to fit in the joint, try removing the ring and flipping it around.)
- Partially tighten the adjuster ring over the threads of the attachment point. Leave room for further adjustment after installing onto the vent
INSTALLING YOUR MAGNETIC CHARGING VENT MOUNT
-
Hold down the clip release button to open the vent clip.
-
Push the vent clip onto the vent blades, sliding it back as far as possible.
-
Turn the ring adjuster counterclockwise to loosen the ball joint and adjust the amount to your preferred viewing angle.
-
Once the mount is in position, turn the ring adjuster clockwise to lock it into place.
MOUNTING/CHARGING YOUR PHONE
-
Plug the Type C end of the charging cable into the Type C port at the bottom of the mount and the USB end into your car charger.
-
Line up the magnetic coils in your magnetic phone/phone case with the magnetic charging ring on the mount. The mount will now hold and charge your phone.
GUARANTEED FOR LIFE
Lowe’s warrants to the consumer that the product and all accessories provided
in the sales package (“Product”) are free from material defects in material
and workmanship when used normally and in accordance with operation
instructions. Lowe’s will repair or replace (at Lowe’s option), without
charge, a Materially Defective Product. If we repair or replace a Materially
Defective Product under the terms of this warranty, this warranty also applies
to repaired or replacement Products. If we repair this Product, we may use new
or refurbished replacement parts. If we choose to replace this Product, we may
replace it with a new or refurbished Product of the same or similar design.
Lowe’s will return repaired or replacement Products to you in working
condition. We will retain defective parts or equipment. Repair or replacement
of Product is your exclusive remedy.
This warranty does not cover Product that has been subjected to misuse,
accident, shipping or other physical damage, improper installation, abnormal
operation or handling, neglect, inundation, fire, water or another liquid
intrusion, or Product that has been damaged due to repair, alteration or
modification by anyone other than a Lowe’s authorized representative.
Customer Service:
We’re here to help. If you are not fully satisfied with this product or have
questions on how to use it, please call our customer service department at
866-994-4148, 8 a.m. – 8 p.m., EST,
Monday – Sunday.
You could also contact us at
partsplus@lowes.com.
Visit www.lowes.com
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment should be installed and operated with a minimum distance of
2ocm between the radiator and your body.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the followingmeasures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Printed in China
AS22334 05/2022
Documents / Resources
|
UTILITECH 204 1001 UT4 Magnetic Charging Vent
Mount
[pdf] Instruction Manual
2041001, 2ADH6-2041001, 2ADH62041001, 204 1001 UT4, Magnetic Charging Vent
Mount, 204 1001 UT4 Magnetic Charging Vent Mount, 5061445
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>