UTILITECH 6940901330 4CT Motion Activated Linkable Solar Wall Lights Installation Guide

6940901330 4CT
Motion Activated Linkable Solar Wall Lights
Installation Guide

Thank you for purchasing this Utilitech product. We’ve created these easy-to- follow instructions to ensure you spend your time enjoying the product instead of putting it together. But,  if you need more information than what is provided here, please visit Lowes.com, search the item number and refer to the Guides & Documents tab on the product’s page.
If you have any questions or problems, please call our customer service department at 1-866-994-4148, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com or visit www.lowespartsplus.com.

IMPORTANT INFO
Please read and understand this entire manual before attempting to assemble, operate or install the product.

• If installing more than 1 light, and you would like to use the linkable function, you must link your lights first before installation and mounting. You may link up to 30 nights. After the lights are linked you may begin the installation process.
• Plan to mount your motion light in a position that allows for the most direct sunlight in order to charge the internal battery most efficiently. Be aware of objects such s trees or property overhangs that may block the solar panel’s exposure to sunlight.
• Prior to installing the light, an initial charge is needed and should be done in the OFF position for at least 1 to 3 days in direct sunlight. Afterward, the included rechargeable battery will be charged sufficiently for operation. Before mounting place the light in the ON position.
• A rapidly flashing light means the battery is undercharged. It is best to turn the light’s switch to the OFF position and charge for 1 to 3 days insufficient sunlight to ring the battery to full charge. Afterward, turn the switch back to the ON position.
• The motion sensor is very light-sensitive. For best performance at night, ensure there is no interfering light preventing the sensor from working correctly.

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged  to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

PACKAGE CONTENTS

HARDWARE CONTENTS

Note: Hardware showed the actual size.

INSTALLATION OVERVIEW

Test:

1. Turn all the light switches to the same LINK position.
2. Place all the solar panels facing down, so the lights are off. Then trigger the sensors and all the lights turn on, connection successfully.

|
---|---
|
PROBLEM| POSSIBLE CAUSE| CORRECTIVE ACTION
---|---|---
The light will not come ON.| 1. The battery is low or drained.
2. The light may be detecting daylight or light from another source preventing the light from coming on.| 1. To charge the battery fully.
2. Relocate the light.
The light stays in low brightness, the battery does not fully charge.| 1. If there are overcast days, the solar panel may not convert enough daylight to recharge the battery sufficiently.
2. There is not enough sunlight.
3. There is dust and debris on the solar panel.| 1. Wait for the sunny day or charge with a USB.
2. Reposition solar panels to receive more sunlight.
3. Clean dust and debris from the solar panel.
The lights of the same
The link is not ON.| 1. The LINK setting is wrong.
2. The distance between the lights is too long.
3. There is a wall between the lights.| 1. Check the LINK setting and change to the same LINK.
2. Make sure the distance between the lights is not more than 60ft.
3. Choose another suitable place to install the lights.
The light stays ON.| 1. The motion sensor may be picked up a heat source like an air vent, dryer vent, or brightly painted, heat-reflective surface.| 1. Reposition the motion sensor or remove such heat
source.
The light comes on during the day.| 1. The motion sensor may be installed in a relatively dark location.| 1. Relocate the light.

PREPARATION

Before beginning the assembly of the product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 15 minutes per light

TOOLS REQUIRED (NOT INCLUDED)

CARE AND MAINTENANCE

• The solar motion light can be cleaned with a damp cloth. This will ensure optimal performance and battery charging.
• Never let any abrasive material come into contact with the solar panel.

WARRANTY

This product is covered under a 3-year limited warranty. Manufacturer warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase. The included battery is not covered under this warranty. Proof of purchase including the date and explanation of the complaint is required for warranty service.

FEELING CONFIDENT? START YOUR NEXT PROJECT

• Visit www.lowes.com for more information

NOTES/RECOMMENDED INSTALL HEIGHT

• Ideal height is 5 Ft. – 8 Ft. from the ground. At such a height, the fixture will provide a detection distance of up to 26 feet. The ideal ambient temperature is 77 degrees Fahrenheit with a relative humidity between 30%-80%.
  

• The motion sensor is the most sensitive as a person or object moves parallel to the sensor.

• The motion sensor is the least sensitive if a person or object moves directly at the sensor head.

• Do not mount the fixture near a heat source like an air conditioner, vent, or furnace exhaust, or in a direction facing a reflective object or nearby light source.

• The sensor cannot be placed less than 5 Ft. from any reflective material. If the light flashes, the sensor is too close to such material. If this happens, move the light fixture.

LINKABLE SET-UP

NOTE/NOTA: This function is for linking 2 or more lights together.

OFF: Turn off fixture
ON: Turn on the fixture (a single fixture in motion mode)
LINK 1: Linkable function (Only fixtures that are setting in LINK1 mode will be connected)
LINK 2: Linkable function (Only fixtures that are setting in LINK2 mode will be connected)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>