Laserliner 081 134 Super Square Laser 4 Multi-Line Laser Instruction Manual

: June 5, 2024
: Laserliner

Table of Contents

Laserliner 081 134 Super Square Laser 4 Multi-Line Laser
General safety instructions
Safety instructions
Safety instructions
Inserting batteries
OVERVIEW
On-floor applications
Wall applications
Mounting on the wall
Checking the vertical line
Information on maintenance and care
EU directives and disposal
SERVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Laserliner 081 134 Super Square Laser 4 Multi-Line Laser

Laserliner-081-134-Super-Square-Laser-4-Multi-Line-Laser-
PRODUCT

Completely read through the operating instructions, the „Warranty and Additional Information“ booklet as well as the latest information under the internet link at the end of these instructions. Follow the instructions they contain. This document must be kept in a safe place and if the laser device is passed on, this document must be passed on with it.

90° line Laser

The 4 clearly visible laser lines are ideally suited for aligning tiles.
Vertical and horizontal leveling on walls
The applied lay edges and contact surface make it easy to position floor tiles.
Clean application on all surfaces – also when using pins
Vials to adjust the device

General safety instructions

The device must only be used in accordance with its intended purpose and within the scope of the specifications.
The measuring tools and accessories are not toys.
Keep out of reach of children.
Modifications or changes to the device are not permitted, this will otherwise invalidate the approval and safety specifications.
Do not expose the device to mechanical stress, extreme temperatures, moisture or significant vibration.
The device must no longer be used if one or more of its functions fail or the battery charge is weak.

Safety instructions

Using class 2 lasers

Laser radiation!
Do not stare into the beam!
Class 2 laser
< 1 mW · 635 nm
EN 60825-1:2014/AC:2017

Attention: Do not look into the direct or reflected beam.

Do not point the laser beam towards persons.
If a person‘s eyes are exposed to class 2 laser radiation, they should shut their eyes and immediately move away from the beam.
Under no circumstances should optical instruments (magnifying glass, microscope, binoculars) be used to look at the laser beam or reflections.
Do not use the laser at eye level (1.40 … 1.90 m)
Reflective, specular or shiny surfaces must be covered whilst laser devices are in operation.
In public areas shield off the laser beam with barriers and partitions wherever possible and identify the laser area with warning signs.

Safety instructions

Dealing with electromagnetic radiation
The measuring device complies with electromagnetic compatibility regulations and limits in accordance with the EMC Directive 2014/30/EU.
Local operating restrictions – for example, in hospitals, aircraft, petrol stations or in the vicinity of people with pacemakers – may apply.
Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.

Inserting batteries

Open the battery compartment (8) and insert batteries according to the symbols. Be sure to pay attention to polarity.

OVERVIEW

Laserliner-081-134-Super-Square-Laser-4-Multi-Line-Laser-
FIG-2

ON / OFF switch
Vials for wall applications
Laser output windows
90° try-square edge
Contact surface
Lay edge
Pins
Battery compartment

On-floor applications

Turn on the unit with the ON / OFF switch (1). The laser lines now produce four marks at 90° angles on the floor.
These projected lines allow tiles to be laid easily, yet precisely. The 90° lay edge (4) and the contact surface (5) make it easy to align the first-floor tile.

Wall applications

Mount the device on the wall for horizontal and vertical leveling. Then align the device with the vials.

Mounting on the wall

Place the devise on the wall.
Push the special pins through the appropriate holes.

Regularly check the calibration before use, after transport, and after extended periods of storage.

Checking the vertical line

Fix a plumb bob with a line at least 2.5 m in length on the wall, making sure that the bob can swing freely. Switch on the laser, direct the lines at the plumb and align the bubble levels (2). The precision is within tolerance if the deviation between the laser line and the plumb line is not greater than 0.5 mm / m.

Calibration

The measuring device should be calibrated and tested on a regular basis to ensure it is accurate and working properly.] We recommend the measuring device is calibrated every 1 – 2 years. If necessary, contact your distributor or the UMAREX-LASERLINER service department.

Information on maintenance and care

Clean all components with a damp cloth and do not use cleaning agents, scouring agents, and solvents. Remove the batteries before storing for longer periods. Store the device in a clean and dry place.

Technical Data (Subject to technical changes without notice. 20W41)

Angle accuracy| ± 0.5 mm / m
Visibility (typical)*| 15 m
Laser wavelength| 635 nm
Laser class| 2 / < 1 mW

(EN 60825-1:2014/AC:2017)

Power supply| 2 x 1.5V LR6 (AA)
Operating time| approx. 15 hours

Operating conditions

| 0°C … 50°C, max. humidity 80% rH, no condensation, max. working altitude 4000 m above sea level
Storage conditions| -10°C … 70°C,

max. humidity 80% rH

Dimensions (W x H x D)| 200 x 48 x 100 mm
Weight| 260 g (incl. batteries)

at max. 300 lux

EU directives and disposal

This device complies with all necessary standards] for the free movement of goods within the EU.] This product is an electric device and must be collected separately for disposal according to the European Directive on waste electrical and electronic equipment.

Further safety and supplementary notices at: http://laserliner.com/info?an=AHP

Laserliner-081-134-Super-Square-Laser-4-Multi-Line-Laser-
FIG-5