ETA Viento 6284 90000 Steam iron User Manual

ETA Viento 6284 90000 Steam iron

INSTRUCTIONS FOR USE

Dear customer, thank you for buying our product. Before putting the appliance into operation, read carefully these instructions for use and store this manual properly together with the certificate of warranty, a cash voucher and possibly with the package and the internal contents of the package. According to the type, the ironing plate has the Eloxium or Ceramic layer that ensures extreme hardness of the coating, it is resistant to scratching and it keeps its excellent gliding property permanently. The iron enables both dry ironing and steam ironing. It is equipped with elements increasing comfort of use – intensive/vertical steaming, sprinkling device, and systems DRIP STOP, SELF CLEAN, ANTI CALC. The handle of the iron is closed and it is adapted for ironing with the right and the left hand. At the back side the handle forms a support that enables putting it in the rest position. Handling while ironing is easier thanks to a swing-out power cable terminal. The electronics automatically switch the heating element on and off during ironing that maintains the set temperature. Regulation of the ironing plate temperature takes place in pre-set steps.

SAFETY WARNING

• Before the first use, read all the instructions for use carefully, look at the picture and keep the instructions for later use. Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
• Check whether the data on the type label corresponds with the voltage in your socket. The power cord plug has to be connected only to electric installation socket complying applicable standards. Use of separate electric circuit with 16 A fuse is recommended.
• The electric socket must be easily accessible to easy disconnect the iron in dangerous and/or emergency situations.
• Do not insert to or take out the plug from a socket with wet hands and do not pull the power cord!
• Do not leave the iron plugged in power supply without supervision!
• Never use the appliance if its power cord or plug is damaged, if it does not work properly, if it fell down and was damaged and is leaking. In this case take the appliance to a special service to check its safety and proper function.
• This product can be used by children at the age of 8 years and older and people with reduced physical or mental abilities or lack of experience and knowledge if they are supervised or if they were instructed regarding use of the appliance in a safe way and if they understand possible risks. Children must not play with the appliance. User cleaning and maintenance must not be performed by children if they are younger than 8 year and unsupervised. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
• Iron and its supply keep out of reach of children under 8 years (when is plugged into power or cools down).
• Use and place the iron on a stable surface.
• When putting the iron on a stand, make sure that the surface that the stand is placed on is stable.
• Whenever you fill the container with water during ironing and empty the container after ironing, unplug the iron from the electric power.
• The appliance is intended for use in households only and for similar use (in shops, offices and similar areas, in hotels, motels and other residential areas, in bed and breakfast facilities)! It is not designed for commercial use!
• Do not use the iron outdoor!
• Do not use the iron as room heating device!
• Do not put any objects to the iron.
• Do not use the appliance with program, time switch or any other item, which switches ON the appliance automatically, as there is a risk of fire, when the appliance is covered or improperly located.
• Never iron or steam iron the clothes on persons (directly on body) and do not direct the steam to any persons or animals.
• The thermostat can never be used as a switch!
• Never immerse the appliance into water (even its parts)! Do not wash it under running water!
• Any modification of the appliance surface (e.g. by means of self-adhesive wallpaper, foil etc.) is prohibited!
• Do not place the iron in such a way that could represent harm (e.g. fire, burn and scalding).
• Due to production tests, the internal iron container can be misted up. Do not consider it to be a defect when purchasing the iron.
• Never pour water to the container that was produced by defrosting of a freezer, water condensed in a dryer, air-conditioning or dehumidifying units, certain types of mineral waters, rain-water, water enriched with alcohol, perfume and preparations for treatment and for stiffening fabrics (e.g. starch, fabric conditioners) or vinegar, decalcifying agents, softeners or other chemical substances. Do not use pure distilled water.
• When ironing, be very careful, tilting of the iron may result in the hot water pouring out of the filling hole.
• Make sure that the power cord is always dry and it is not damaged.
• Regularly check condition of the appliance power cord.
• The power cord must not be damaged with sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges. Never put it to hot surfaces, prevent its free hanging over edge of table or workboard. Touching, stumbling or pulling the power cord e. g. by children may cause tipping over or falling of the appliance with subsequent severe injury!
• The appliance is portable and it is equipped with a movable connector with a plug which ensures double-pole disconnection from power supply.
• If you need to use the extension cord, it has to be uncorrupted and it has to comply with the valid standards.
• Never use the appliance for any other purpose than for that described in these instructions for use!
• The producer is not responsible for damage caused by improper use of the appliance (e.g. burning, scalding, fire, clothes damage, scratching and contamination of the ironing plate) and its guarantee for the appliance does not apply to situations when the safety warnings above have not been complied with.

DESCRIPTION OF THE APPLIANCE

• A – ironing plate
• B – additional spray jet
• C – filling hole lid
• D – steaming regulator
• E – additional spray button
• F – steam shock button
• G – control light
• H – thermostat regulation wheel
• I – water container
• J – SELF CLEAN button
• K – rest board
• L – space for power cord wind-up
• M – power cord
• N – handle
• O – filling cup

INSTRUCTIONS FOR USE

Remove all the packing material and take out the iron with the accessories. Remove any labels, protective foils or covers from the ironing plate before the first use. At first switch the iron ON to maximum temperature and let the iron at least 10 minutes running without water. The iron may produce slight smoke, which is cased by the burning of used lubricants and seals in steam chamber. This is normal situation and does not form the reason for warranty claim. During first filling of the tank with operating water it is recommended to release the steam from whole tank outside the ironed fabric.

Ironing temperatures

• Sort laundry and iron according to the instructions for treatment (e.g. manufacturer’s recommendation – the label on clothes). If the instruction is missing and you know the material of the clothes, follow the table on picture 3. The table applies to basic materials only, not to possible decorations, material treatment, etc.
• Start to iron from the lowest temperatures to higher temperatures. If clothes consist of e. g. two and more materials or if they contain stringing, purls, embossing, stretch material, etc., always iron according to the material requiring the lower temperature only. If you do not know the material, find a suitable place that is not visible when wearing and try suitable temperature for ironing at the place.
• When ironing woollen fabrics, we recommend ironing on the back side of the fabric and you can iron virgin wool through the additional cloth. Velvet and similar fabrics can be ironed in one direction (you will prevent creation of glossy areas).
• Steam ironing is not suitable for fabrics from synthetic and silk fibers (e.g. acrylon, nylon, polyamide or polyester).
• We recommend using soft textile permeable base materials for steam ironing.
• Make sure that the ironed fabric is tensed up properly so that steam does not leak to the sides.
• For the ironing plate to remain smooth, protect it from direct contact with sharp metal objects (e.g. zip fasteners, buttons, snap buttons, decorative objects).

Ironing without steaming

Plug the power cord M to electric socket; control is lit. Put the iron to the rest position (Fig. 7). Turn the steaming regulator D to the 0 position, steaming off (fig. 5) or pour out water from container I. Set the program on the display using regulation wheel H according to the selected fabric material (Fig. 2). Reaching the required temperature is shown by turning the indicator lamp G OFF.

WARNING
During ironing, the thermostat will cycle, which is accompanied by characteristic sound (clicking). This is normal situation and does not form the reason for warranty claims related to the appliance.

Recommendation

Control H (Fig. 2) is marked with international symbols that recommend the optimum ironing temperature and they are the same as marking on some types of laundry
and textiles (Fig. 3). When the temperature is increased from the cold state or if the temperature is set from higher to lower, we recommend waiting for a while (see the information on the display and listen for sound signaling) due to stabilization of the ironing plate temperature.

Steam ironing

Hold the iron in your hand, turn the steaming regulator D to position 0 (Fig. 5) and slide the cover C to open the filling container lid. Pour in water to container I (Fig. 4) with the enclosed cup O and close the filling hole lid in the opposite direction. Keep the position of the iron for pouring in water. Put the iron to the rest position (Fig. 7) and set the regulation wheel H to the marked area for steaming (Fig. 2 – ). Plug the power cord M to a socket. When the control light G goes off, move the steaming regulator D away from handle. The more you move the regulator towards MAX, the bigger amount of outgoing steam there will be (Fig. 5). Place the iron to the rest position, automatic creation of steam will stop (more steam may be going out for a short time).

Warning

• For all normal ironing, the middle adjustment of the steam amount is recommended. Only on ironing the linen fabric, thick cotton and similar fabrics the adjustment of the steam amount to maximum value is recommended. Setting to high-pressure steam ironing os recommended only if the regulation wheel H is set to temperature setting •••.
• Be extra careful to avoid accidental pushing of the SELF-CLEaN button.
• When water container I is filled with water over the permitted limit (MAX. 300 ml), steam can be created even in the rest position.
• At places with hard water we recommend diluting it with distilled water. You will get the information about water hardness at the water-management authorities, or at the local sanitary station. For water hardness > 15 °N we recommend filling the iron in the following ratio:

Sprinkling appliance (additional spray)

It is used for moistening fabrics and it is effective in ironing extremely creased fabrics. It is activated by repeated pressing of additional spray button E. We do not recommend applying additional spray for fine fabrics (e.g. silk and synthetic) as the used water may stain the fabric.

Intensive steaming (steam shock)

Use only if the steam ironing is insufficient. In this case press intensive steaming button F several times (Fig. 6A ). Thus you will get additional steam except for the steam created by standard steaming.

Warning
When you press intensive steaming button F several times, water may drip from the ironing plate due to excess water in the steam chamber. Do not consider this a faulty operation.

VERTICAL SYSTEM

It is intensive vertical steaming for steaming of freely hanging textiles (such as hanging clothes, draperies, hangings). Set the regulation wheel H to the marked area for steaming (Fig. 2). As soon as the indication lamp G turns OFF, stretch the fabric slightly with one hand and move the iron vertically bottom-up (Fig. 6B). Press the intensive steaming button F so that you reach vertical steam hammer. Do not hold the intensive steaming button pressed continuously and do not use it more than 10 times consecutively.

CAUTION

• Prevent burning of sensitive fabrics, do not close them to the iron to distance of 10 to 20 cm.
• Use the VERTICAL function only if the regulation wheel H to the ••• or maximum position.
• Do not iron clothes that you or other people are wearing!
• Never direct steam flow to persons or animals!

DRIP STOP
The appliance prevents leaking water from the ironing plate when its temperature is insufficient.

Safety electronics (AUTO STOP – applies for type ETa 2284 and ETa 6284/10)

The safety electronics ensures switching OFF the iron plate heating within 30 seconds, when the iron is left without any movement in horizontal position or when it is tilted over to one side, or within 10 minutes, when it is left in vertical position. Function of safety electronics is signalled by flashing of indicator lamp G and by acoustic signal (beep). The iron is restarted automatically when the ironing is resumed.

Self-cleaning system (SELF-CLEAN)

Hold the iron disconnected from power supply in your hand, turn steaming regulator D to 0 position (Fig. 5) and lift off cover C to open the filling container lid. Pour water into container I using the enclosed cup O to fill half of it and close the filling hole lid (Fig. 4) by snapping it. Keep the position of the iron for pouring water in it. Put the iron to the rest position (Fig. 7) and set the regulation wheel H to the maximum position. Plug power cord M into a socket. When the control light G switch off, disconnect the iron from the electric power. Hold the iron in the horizontal position over a sink. Press the SELF CLEAN button repeatedly (two to three times), each time for about 5 seconds. Then wait till water stops going out from the ironing plate. If the iron still contains a lot of impurities, repeat the procedure while pushing the intensive steaming button between individual pushing of the SELF-cLEaN button. After completing the cleaning, plug the iron into the electric power, set the selected program and then iron a clean piece of cotton cloth so that the ironing plate is cleaned. clean the ironing plate using the SELF-CLEAN function continuously.

Storage

After finishing ironing, pour out the unused water from the container (be careful, it can be hot), or let the rest of the water evaporate and let the iron cool down. Then turn regulator D to 0 position (steam switched off). Wind power cord M over the back side of cover L and put the iron to the rest position (Fig. 8) out of reach of children and incapacitated persons.

MAINTENANCE

Before every maintenance, unplug the iron from power supply by taking the fork of the power cord out of the socket! Do not use rough and aggressive detergents (e.g. sharp objects, peelers, pot scourers, caustic agents for cleaning or other solvents). Wipe the entire iron with a wet cloth in the cooled state and dry up. If brown film is created on the ironing plate (e.g. when ironing starched laundry), you can remove the film by a detergent containing fine sand. The iron is equipped with a permanent decalcification system aNTI caLc that does not require maintenance. But the system cannot fully prevent creation of calcareous sediments.

TROUBLESHOOTING

socket
Thermostat regulation wheel is in MIN position| Set the wheel to position • / •• / ••• or MAX
AUTO STOP function activated| Move the iron for deactivation of the safety function
Iron does not create steam| There is no water in the container| Pour water into the container
Steaming regulator is in 0 position| Move the regulator into the steaming position
Low temperature is set for activa- ting the DRIP-STOP function| Use the regulation wheel to set a temperature, during which you can use steaming and wait till the iron is heated for using it
Iron does not crea- te steam shock| Low temperature is set for activa- ting DRIP-STOP function| Use the regulation wheel to set a temperature, during which you can use steaming and wait till the iron is heated for using it
The function of steam shock was used too often during a short period of time| Let the iron heat and wait for a while before using the electric shock function again
Sprinkling equip- ment (additional spray) does not sprinkle water| There is no water in the container| Pour water into the container
---|---|---
The water system is aerated| Tighten finger on the additional spray jet hole and at the same time press the sprinkling device button several times
Water is dripping from the ironing plate| The lid of the pouring hole of the container is not closed properly.| Close the pouring hole lid
Low temperature is set| Use the regulation wheel to set a temperature, during which you can use steaming and wait till the iron is heated for using it
The steam shock function was used when temperature below ooo was set| Use the regulation wheel to set a tem- perature ••• or MAX
The SELF CLEAN button was pressed during ironing| Do not use the SELF CLEAN function
After finishing ironing, the iron was put into the horizontal position and the steaming regulator is not in 0 position| Move the steaming regulator to 0 po- sition, empty the container and put the iron into the rest position
Flakes and other impurities are pee- led off the ironing plate| Contrary to recommendation undi- luted water is used with excessive hardness > 15 °N| Use water diluted with distilled water
Clean the iron using the SELF CLEAN function and steam shock
Brown liquid is pouring out of the ironing plate| Improper chemical agents were used for removing scale| Do not add any chemical agents into the water container for removing scale
You use one of the types of water that we do not recommend| Use only common clean drinking water for filling in the container, or water diluted with distilled water
Fibers from linen got into the holes in the ironing plate and they are burning there| Clean the iron using the SELF CLEAN function and the steam shock, or va- cuum the cooled plate delicately from time to time
The ironing plate is dirty or it has brownish colour| High temperature is set| Set the program/temperature by the control that corresponds to the ironed material so that the material is not burned on the ironing plate
Laundry is not sufficiently rinsed and it contains residues of wa- shing powder, softener or starch| Clean the ironing plate (see Mainte- nance).

Rinse the laundry properly.

The ironing plate surface is scratch- ed| The plate was in contact with sharp and hard objects while ironing| During ironing, avoid contact with metal objects containing sharp edges and do not put the iron on a metal base with sharp edges and protrusions

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for production of packing, components and accessories as well as their recycling on all parts of the appliance The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal, hand them over at the special collection places where they will be accepted free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authorities or at a collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. If the appliance is to be put out of operation for good, after disconnecting it from power supply we recommend cutting off the power cord and in this way it will not be possible to use the appliance again. more extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service! Failure to comply with the instructions of the manufacturer will lead to expiration of the right to guarantee repair!

TECHNICAL DATA

• Voltage (V) specified on the type label
• Input (W) specified on the type label
• Water volume (volume ml.) 300
• Weight without water (kg) about 1,6

The product matches the requirements of the below statutory order as amended:

• Committee Regulation No. 2006/95/ES as amended, setting the technical requirements of the electrical appliance as low.
• Committee Regulation No. 2004/108/ES as amended, setting the technical requirements of products in terms of their electromagnetic compatibility.

The manufacturer reserves the right to make insignificant changes to the standard design that do not affect the function.
HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER. TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY
PRODUCER: ETA a.s., Zelený pruh 95/97, 147 00 Praha 4-Bráník, Czech Republic.

References

• ElektroEko – Odbiór odpadów elektro
• Úvod | ELEKTROWIN, a.s.
• Úvod - Envidom
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>