concept CE-3510 Electric Citrus Press Instruction Manual

: June 5, 2024
: concept

Table of Contents

IMPORTANT SAFETY WARNINGS
PRODUCT DESCRIPTION
INSTRUCTIONS FOR USE
CLEANING AND MAINTENANCE
SERVICING
ENVIRONMENTAL PROTECTION
WARRANTY TERMS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Citrus Press

concept CE-3510 Electric Citrus Press

ACKNOWLEDGMENT
Thank you for purchasing a Concept product. We hope you will be satisfied with our product throughout its service life. Please study the entire Operating Manual carefully before you start using the product. Keep the manual in a safe place for future reference. Make sure that all other people using the appliance are familiar with the contents of the instruction manual.

Technical parameters

Voltage| 230 V
Power input| 40 W

IMPORTANT SAFETY WARNINGS

Before starting to use the appliance, please read carefully all instructions.

Check if the voltage on the product’s label corresponds to your power supply voltage.
Never leave the appliance in operation unattended. Keep out of the reach of children.
Never use the appliance if it shows any signs of damage or if its power cord is damaged.
The appliance is intended for household use.
Never use the appliance close to hot surfaces.
If the power cord is damaged, only qualified persons may replace it.
Never use the appliance outdoor. Store in a dry environment.
Never use accessories unapproved by the manufacturer.
Never lift and carry the device by the power cord.
Do not crease the power cord.
Never use the device close to the wash basin or close to other water sources.
Never dip the device into water or any other liquids.
If dropped into water, please proceed as follows:
– Disconnect the power supply immediately.
– Do not put your hands into the water.
– Prior to further use have the device checked by a qualified person.
Make sure the device is never wet (sprinkled with water etc.).
This appliance may be used by children 8 years of age and older and by persons with physical or mental impairments or by inexperienced persons if they are properly supervised or have been informed about how to use of the product in a safe manner and understand the potential dangers. Children must not play with the appliance. This appliance may be cleaned by children 8 years of age and older if they are properly supervised. Keep this appliance and the power cord out of reach of children younger than 8 years of age.

concept CE-3510 Electric Citrus Press - fig1

PRODUCT DESCRIPTION

Dust shield (for storing)
Large cone (to obtain the maximum quantity of juice from large fruits such as grapefruits and oranges)
Small cone (for smaller fruits such as lemons and limes)
Rakes (preventing fruit pulp from settling in the sieve and facilitating juice pressing from the pulp)
Sieve (serves to filtrate the pulp and stone while juice flows down into the container)
Juice container (capacity 0.6 l)
Reverse-run spindle (rotating the cone in the opposite direction if pressed by the user)
Base unit with motor (with power cord storage compartment)

Warning: Appliance is intended for short intervals of use.
The device is designed for processing average quantities of fruits in a household. It can be operated without break for maximally 5 minutes and it should be let cool down for approximately 5 minutes.

INSTRUCTIONS FOR USE

Place the base unit onto a dry and even surface.
Put the juice container onto the spindle so that it touches the base unit and make sure the motor pin correctly bears on the cavity in the juice container bottom.
Put the sieve on the removable juice container and make sure the sieve handle precisely bears on the corresponding cavity in the juice container . Place the small cone on the spindle.
Plug the device’s power cord into a power socket.
Cut fruits into two halves.
Firmly press each half on the small or large cone; the motor starts automatically. Fruits shall run down into the removable juice container through the sieve.

Warning:

Never use the appliance longer than 5 minutes – the motor might get damaged.
The device may be used in households only for the intended use corresponding to its design.

CLEANING AND MAINTENANCE

Disconnect the device’s power cord from the power socket.
Parts (1, 2, 3, 4, 5, 6) can be removed and immersed in warm water containing detergent. Never immerse parts (7) and (8) into water or any other liquid.
Do not wash these parts in a dishwasher!
The parts could get deformed by hot water and cleaning agents.
All removable parts must be rinsed immediately after use before the fruit pulp dries.
The dried pulp may be difficult to remove and leave blurs.
After washing and rinsing the removable components, please dry them well.

Clean the base unit with a motor using a humid cloth. Never use aggressive cleaning agents and hard brushes the appliance might become scratched.
IMPORTANT WARNING: NEVER IMMERSE THE BASE UNIT WITH THE MOTOR INTO WATER OR ANY OTHER LIQUIDS.

SERVICING

Any extensive maintenance or repair requiring access to the internal parts of the product shall be performed by an authorized service center.

ENVIRONMENTAL PROTECTION

Packaging materials and obsolete appliances should be recycled.
The transport box may be disposed of as sorted waste.
Polyethylene bags shall be handed over for recycling.

Appliance recycling at the end of its service life:
A symbol on the product or its packaging indicates that this product should not go into household waste. It must be taken to the collection point of an electric and electronic equipment recycling facility. By making sure this product is disposed of properly, you will help prevent the negative effects on the environment and human health that would otherwise result from the inappropriate disposal of this product. You can learn more about recycling this product from your local authorities, a household waste disposal service, or in the shop where you bought this product.

This product meets all the basic EU regulation requirements that relate to it.
Changes to the text, design, and technical specifications may occur without prior notice and we reserve the right to make these changes.

WARRANTY TERMS

Warranty
The manufacturer (or importer) is responsible for ensuring the product complies with the requirements of applicable legal regulations as well as those of the relevant technical standards. Moreover, they are responsible for ensuring the product has the properties the manufacturer described in documents related to the goods or those reasonably expected by the customer with regard to the nature of the goods or based on advertising produced by the manufacturer, and further, they are responsible for ensuring the product is ﬁ t for the purpose proposed by the manufacturer or that a product of the same type is normally used for. The quality warranty term is 24 months from product takeover by the customer. The warranty does not apply to wear and tear caused by regular use. The customer shall not be entitled to any warranty claims if, prior to taking the product over, they knew the product contained a defect or if the defect is attributable to the customer.

The warranty speciﬁ cally does not apply:

if the product installation, operation, and service conditions stipulated in the product operating manual have not been adhered to,
to malfunctions caused due to mechanical, heat, or chemical damage, short circuit, over-voltage, or incorrect installation,
to malfunctions caused by an inexpert third-party intervention,
to malfunctions caused by natural disasters,
to malfunctions caused by insuﬃ client or inappropriate maintenance in violation of the operating manual, including malfunctions caused by water and other sediments,
to changes in the color of the heating surface or to scratching of the surface caused as a result of using the products in an unusual manner,
to appearance and functional changes caused by exposure to sunlight, thermal radiation of water and other sediments,
if the service life of certain product parts expires, e.g. for accumulators, bulbs, etc.

The warranty does not apply to any products and services provided along with the product (gifts, promotional articles, etc.).

Filing a complaint
A complaint against a product defect must be ﬁ led as soon as identiﬁ ed, yet no later than before the end of the warranty term. The customer must ﬁ le a product compliant with the dealer from which they have purchased the product, or with any authorized service center, a list of which is included in the product package, or available at
www.my-concept.com.

While ﬁ ling a product complaint, the product must be duly cleaned and securely packed so as to prevent any damage during its transport to an authorized service center, where relevant, unless the product is delivered in person. The customer must submit proof of having concluded a purchase contract for the product by producing the receipt. While ﬁling their complaint, the customer must indicate the noted defect and identify the preferred complaint application method.

Complaints processing
As long as the noted defect may be removed, the user has the right to have the defect duly removed free of charge on a timely basis. Where such a procedure is not reasonable with regard to the nature of the defect, the user may require to be supplied a new defect-free product (replacement), or, where the defect applies to a part of the product only, replacement of the part concerned. However, if replacement of the product or any part thereof is not proportionate with regard to the nature of the defect, especially if the effect can be removed without undue delay, the customer has the right to have the defect removed free of charge.

If the noted defect is not removable, or if the customer becomes entitled to replacement of the product or a part thereof, yet the replacement is not possible, for example due to the product having been sold out, the customer has the right to return the product (withdrawal from the contract).
The customer shall have the right to a new product (replacement) or to replacement of a part of the product even if the defect can be removed, provided they cannot properly use the product due to repeated occurrence of the defect or due to a high number of such defects. In such a case, the customer also has the right to return the product (by withdrawing from the contract).

If the product is not returned (the customer does not withdraw from the contract), or if the customer does not apply the right to a new defect-free product (replacement), to replacement of a part thereof, or to repair the product, they may request a reasonable discount. The customer also has a right to a reasonable discount if a new defect-free product cannot be supplied to them, or if a product part cannot be replaced or the product repaired unless the situation is remedied within a reasonable time limit, or if remedying the situation would create major discomfort on the part of the customer. The seller-authorized service center or a staﬀ member authorized by them must decide about each complaint immediately or within three business days in complicated cases. This term does not include a reasonable period of time, depending on the type of product concerned,

required for the defect to be assessed by an expert. A complaint, including defect removal, must be dealt with without any undue delay, yet no later than within 30 calendar days of the complaint ﬁ ling date, unless the seller and the customer agree on a later deadline. On returning the product (withdrawing from the contract) the customer must return any accessories and documents supplied along with the product. The customer does not have the right to keep the defective parts and components of the product replaced as part of a repair of the product. This shall be without prejudice to any other rights the customer may have in relation to the purchase of the product.

Remark: Complaints against products damaged in transport are governed by the carrier’s complaints procedure.

Manufacturer
Jindřich Valenta – ELKO Valenta
Vysokomýtská 1800, 565 01 Choceň
Czech Republic
tel.: +420 465 471 433
fax +420 465 473 304
Company ID No. 13216660
email: servis@my-concept.cz
www: www.my-concept.com

Product data

Model:|
---|---
Production number:
Date of purchase:| Seal and signature of vendor: