ergotron 24-214-085 WorkFit C Dual Monitor Sit Stand Cart Installation Guide
- June 4, 2024
- ERGOTRON
Table of Contents
WorkFit™ C Dual
For the latest user installation guide please
visitwww.ergotron.com
IMPORTANT! This product will need tension adjustments once the
installation is complete. Make sure all equipment is properly installed on the
product before attempting a range of motion or tension adjustments. Any time
equipment is added or changed on this product resulting in a different mounted
weight, you should repeat the adjustment steps to ensure safe and optimum
operation. This product should move smoothly and easily through the full range
of motion and stay where you set it. If movement is difficult or the product
does not stay where you set it, follow the adjustment instructions to loosen
or tighten the tension to create a smooth, easy motion.
Depending on your product and the adjustment, it may take many turns to notice
a difference.
WARNING
IMPACT HAZARD
MOVING PARTS CAN CRUSH & CUT
Do not remove the zip tie and cardboard spacer which keep the hand brake from
disengaging until instructed in the manual. Removing the zip tie before the
cart is unpacked and standing upright may cause unintended motion of the
riser. Failure to heed this warning may lead to personal injury or equipment
damage.
Do not tip the cart over on the side. The cart must remain upright at all times. Tipping the cart on the side may cause unintended motion of the riser. Failure to heed this warning may result in serious personal injury or property damage!
For more information on the safe set-up, adjustment and use of this product refer to the user manual at www.ergotron.com or contact Ergotron Customer Care at 1-800-888-8458.
823-106-00
19 Adjustment
WARNING
IMPACT HAZARD
Moving Parts Can Crush And Cut!
Minimize Lift Tension BEFORE:
- Removing Mounted Equipment
- Shipping Cart or Storing Cart
To Minimize Lift Tension
- With the cart upright, lower the worksurface to the lowest position.
- Turn the adjustment nut at bottom of the riser counterclockwise until it stops (Adjustment may require 40-60 revolutions).).
Failure to heed this warning may result in serious personal injury or property damage!
Cart Must Remain Upright! Tipping Cart On Side May Cause the Work Surface to
Disengage Causing Serious Personal Injury and Property Damage.
For more information and instructions refer to the product guide at
www.ergotron.com or contact Ergotron Customer
Care at 1-800-888-8458.
Follow these instructions to tighten or loosen tension.
WARNING
Cart Must Remain Upright! Tipping Cart On Side May Cause the Work Surface to Disengage Causing Serious Personal Injury and Property Damage.
Learn more about ergonomic computer use at:
www.ergotron.com/ergonomics
For the latest User Installation Guide please visit:
www.ergotron.com
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit:
http://contact.ergotron.com
www.ergotron.com
USA: 1-800-888-8458
Europe: +31 (0)33-45 45 600
China: 400-120-3051
Japan: japansupport@ergotron.com
© 2019 Ergotron, Inc. All rights reserved. WorkFitt” is a registered trademark
of Ergotron, Inc.
While Ergotron, Inc. makes every effort to provide accurate and complete
information on the installation and use of its products, it will not be held
liable for any editorial errors or omissions (including those made in the
process of translation from English to another language), or for incidental,
special or consequential damages of any nature resulting from furnishing this
instruction and performance of equipment in connection with this instruction.
Ergotron, Inc. reserves the right to make changes in the product design and/or
product documentation without notification to its users. For the most current
product information, or to know if this document is available in languages
other than those herein, please contact Ergotron. No part of this publication
may be reproduced, stored in a retrieval system, or transmitted in any form or
by any means, electronic, mechanical, photocopying, recording, or otherwise
without the prior written consent of Ergotron, Inc.,1181 Trapp Road, Eagan,
Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign. Ergotron is
a registered trademark of Ergotron, Inc.
888-24-166-W-03 rev.F
Documents / Resources
|
ergotron 24-214-085 WorkFit C Dual Monitor Sit Stand
Cart
[pdf] Installation Guide
24-214-085, WorkFit C Dual Monitor Sit Stand Cart, 24-214-085 WorkFit C Dual
Monitor Sit Stand Cart, Dual Monitor Sit Stand Cart
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>