concept ZA 7010 Hair Clipper Instruction Manual

: June 5, 2024
: concept

Table of Contents

**
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**

concept ZA 7010 Hair Clipper

ACKNOWLEDGMENT
Thank you for purchasing a Concept product. We hope you will be satisfied with our product throughout its service life. Please study the entire Operating Manual carefully before you start using the product. Keep the manual in a safe place for future reference. Make sure other people using the product are familiar with these instructions.

Technical parameters

Accumulator voltage| Marked on the rating label
Power input| Marked on the rating label
Noise level| 80 dB(A)

Charging time 8 hours
Time of operation approx. 45 min

IMPORTANT SAFETY INSTRUCTIONS

Use the unit only as described in this operating manual.
Make sure the mains voltage corresponds to the values on the rating plate.
Do not leave the unit unattended while it is turned on or even only plugged into the wall outlet.
When putting down the unit during use, always switch it off.
When the unit is not in use, the protective cover should be put on the blades.
Switch the unit off when changing the blade guards.
Before plugging in or unplugging the unit from the wall outlet, make sure the switch is OFF.
When disconnecting the unit from the wall outlet, never pull the power cord. Grasp the plug and disconnect it by pulling.
Do not allow children or unskilled people to handle the unit. Use the unit out of the reach of these individuals.
Take extra care when using the unit near children.
Turn off the unit and disconnect the power cord from the wall outlet before cleaning and after use.
Do not let the power cord hang loosely over the edge of a table. Make sure the power cord does not touch hot surfaces.
Do not let the unit hang loosely on the power cord.
Do not use abrasive or chemically aggressive substances for cleaning the unit.
Do not touch the body of the unit when it has been exposed to liquid. Disconnect the power cord from the wall outlet first.
Do not use the unit if it does not operate properly, or if it has been dropped, damaged or exposed to any liquids. Refer the unit to an authorized service center for testing and repair.
Do not store or place the unit in places where there is a risk of falling.
Keep the unit away from heat sources, such as radiators, ovens etc. Do not expose the unit to direct sunlight or moisture.
Never use an appliance with a damaged power cord or plug. Contact an authorized service center immediately to have defective components repaired or replaced.
Do not use the unit if the blade teeth or blade guards are damaged.
Do not wrap the power cord around the unit.
Do not use the unit outdoors, in environments with aerosol, or where oxygen is handled.
The unit is suitable for domestic use only. It is not designed for commercial operation.
Do not use the unit on wet or damp hair.
Do not immerse the power cord, plug, or appliance into water or any other liquid
Use only accessories recommended by the manufacturer.
Do not repair the appliance yourself. Contact an authorized service center.
Failure to follow the manufacturer‘s instructions may lead to refusal of warranty repair.

NOTE:
Do not use the unit near bathtubs, basins or other vessels filled with water. When using the unit in a bathroom, make sure you switch it off immediately after use, and disconnect it from the wall outlet, as the proximity of water or any contact of the unit with water is very dangerous, even when the unit is switched off! Do not touch the unit with damp or wet hands, and do not handle it if your feet are wet, or you are barefoot.
concept ZA 7010 Hair Clipper 01

PRODUCT DESCRIPTION

2 Cutting guide for 22 lenghths (from 3–18 mm / 21–36 mm, in 1,5 mm steps)
Precision guide 0,5–2,5 mm
Blades
Thinning system
Thinning system button
Adjust length wheel
On / off button
Charging indicator light
Charging stand
Cleaning brush
Charging adaptor
Comb
Lock system
oil

OPERATING INSTRUCTIONS

The unit is designed to cut hair and beards..
CUTTING

Sit the person in front of you on a chair, so that the person’s head is at the level of your chest.
Cover the person’s neck and shoulders to protect against falling hair.
Brush the hair.
Switch on the appliance.
Cut the hair, applying slow repeated movements. Always cut small sections of hair. We recommend starting with a higher blade guard, then using the lower ones.
The length of the cut can be adjusted slightly using the cut height adjustment lever (Fig. 5).
For easier cutting of longer and curly hair you may use a comb against the blades. Remove the cut hair to prevent clogging of the mechanism.
To cut the hair around the ears and on the nape of the neck, remove the blade guard.
Before you cut the ear line, comb the hair over the ears. To straighten the line on the nape of the neck, turn the mechanism vertically to the skin, and create a clean line, using slow movements (Figs. 6-8).
When putting down the unit during use, always switch it off.
Switch the unit off after use.
When using the unit in a bathroom, make sure you switch it off immediately after use, and disconnect it from the wall outlet, as the proximity of water or any contact of the unit with water is very dangerous, even when the unit is switched off!
Switch the unit off when changing the blade guards!

CUTTING OVER A COMB OR THE FINGERS
This technique requires certain skill; use it when you want a cut longer than 12 mm.

Use the unit without the blade guard.
Comb a small lock of hair upwards, hold it using a comb or the fingers.
Cut the hair that overhangs the fingers or the comb. Comb frequently to remove cut hair.

CLEANING AND MAINTENANCE

WARNING!
Before cleaning the unit, always disconnect the power cord from the wall outlet! Clean the blades with the supplied brush after each use. We recommend oiling the blades after every other use. Apply several drops of oil to the teeth, and switch on the unit to work the oil between the blades. Don’t use hair oil, petroleum or oil containing solvents to lubricate the blades. These can slow the movement of blades when they dry. The surface of the unit may only be cleaned using a wet cloth. Don’t use any detergents or hard objects as they may damage the unit’s surface!
Never clean the unit under running water, do not rinse it, and do not submerge it in water! The protective cover should be put on the blades after cleaning.

TROUBLESHOOTING

Problem	Cause	Solution
Motor does not run.	Plug inserted into the mains outlet incorrectly or
insufficiently.	Check the plug connection.
The mains outlet is not live.	Check for voltage, e.g. by connecting another

appliance.
The supply cable is damaged.| Refer the unit to an authorized service center for testing and repair.
The blades do not cut properly.| The blades are not set or oiled well, or they are blunt.| Disconnect the cable from the socket. Check the setting of blades and oil them. If the quality of the cut does not improve, the blades are blunt and you need to replace them.

ACCUMULATOR DISPOSAL
The appliance contains an Ni-MH accumulator. This accumulator type contains substances that may damage the environment when decomposing. Prior to the appliance disposal or the accumulator replacement, remove the original accumulator and take it to a designated collection yard.
WARNING!

Never throw the accumulator into a fire!
Never disassemble the accumulator!
Never shorten the accumulator terminals!
Be careful when the accumulator is damaged and leaks; the accumulator electrolyte solution is of alkali nature. When your skin gets sprayed, rinse it immediately with water and soap and seek medical assistance. For removing or replacing the accumulator, contact professional service.

REPAIR & MAINTENANCE
Any extensive maintenance or repair that requires access to the inner parts of the product must be performed by an expert service centre.

ENVIRONMENTAL PROTECTION

Packaging materials and obsolete appliances should be recycled.
The transport box may be disposed of as sorted waste.
Polyethylene bags shall be handed over for recycling.
Appliance recycling at the end of its service life
A symbol on the product or its packaging indicates that this product should not go into household waste. It must be taken to the collection point of an electric and electronic equipment recycling facility. By making sure this product is disposed of properly, you will help prevent the negative effects on the environment and human health that would otherwise result from inappropriate disposal of this product. You can learn more about recycling this product from your local authorities, a household waste disposal service or in the shop where you bought this product.

WARRANTY TERMS

Warranty
The manufacturer (or importer) is responsible for ensuring the product complies with the requirements of applicable legal regulations as well as those of the relevant technical standards. Moreover, they are responsible for ensuring the product has the properties the manufacturer described in documents related to the goods or those reasonably expected by the customer with regard to the nature of the goods or based on advertising produced by the manufacturer, and further they are responsible for ensuring the product is ﬁ t for the purpose proposed by the manufacturer or that a product of the same type is normally used for. The quality warranty term is 24 months from product takeover by the customer. The warranty does not apply to wear and tear caused by regular use. The customer shall not be entitled to any warranty claims if, prior to taking the product over, they knew the product contained a defect or if the defect is attributable to the customer.
The warranty speciﬁcally does not apply:

if the product installation, operation and service conditions stipulated in the product operating manual have not been adhered to,
to malfunctions caused due to mechanical, heat or chemical damage, short circuit, over voltage or incorrect installation,
to malfunctions caused by an inexpert third-party intervention,
to malfunctions caused by natural disaster,
to malfunctions caused by insuﬃcient or inappropriate maintenance in violation of the operating manual, including malfunctions caused by water and other sediments,
to changes in colour of the heating surface or to scratching of the surface caused as a result of us-ing the products in an unusual manner,
to appearance and functional changes caused by exposure to sunlight, thermal radiation of water and other sediments,
if the service life of certain product parts expires, e. g. for accumulators, bulbs, etc.
The warranty does not apply to any products and ser-vices provided along with the product (gifts, promo-tional articles, etc.).

Filing a complaint
A complaint against a product defect must be ﬁ led as soon as identiﬁed, yet no later than before the end of the warranty term. The customer must ﬁ le a product complaint with the dealer from which they have purchased the pro-duct, or with any authorised service centre, a list of which is included in the product package, or available at www.my-concept.com.
While ﬁ ling a product complaint, the product must be duly cleaned and securely packed so as to prevent any damage during its transport to an authorised service centre, where relevant, unless the product is delivered in person. The customer must submit proof of having concluded a purchase contract for the product by producing the receipt. While ﬁ ling their complaint, the customer must indicate the noted defect and identify the preferred com-plaint application method.
Complaints processing
As long as the noted defect may be removed, the user has the right to have the defect duly removed free of charge on a timely basis. Where such a procedure is not reasonable with
regard to the nature of the defect, the user may require to be supplied a new defect-free product (replacement), or, where the defect applies to a part of the product only, replacement of the part concerned. However, if replacement of the product or any part thereof is not proportionate with regard to the nature of the defect, especially if the defect can be removed without undue delay, the customer has the right to have the defect removed free of charge. If the noted defect is not removable, or if the customer becomes entitled to replacement of the product or a part thereof, yet the replacement is not possible, for example due to the product having been sold out, the customer has the right to return the product (withdrawal from the contract). The customer shall have the right to a new product (re-placement) or to replacement of a part of the product even if the defect can be removed, provided they can-not properly use the product due to repeated occurrence of the defect or due to a high number of such defects. In such a case, the customer also has the right to return the product (by withdrawing from the contract). If the product is not returned (the customer does not withdraw from the contract), or if the customer does not apply the right to a new defect- free product (replacement), to replacement of a part thereof or to repair of the product, they may request a reasonable discount. The customer also has a right to a reason-able discount if a new defect-free product cannot be supplied to them, or if a product part cannot be replaced or the product repaired unless the situation is remedied within a reasonable time limit, or if remedying the situation would create major discomfort on the part of the customer. The seller, authorised service centre or a staﬀ member authorised by them must decide about each complaint immediately or within three business days in complicated cases. This term does not include a reasonable period of time, depending on the type of product concerned,
Product data
required for the defect to be assessed by an expert. A complaint, including defect removal, must be dealt with without any undue delay, yet no later than within 30 calendar days of the complaint ﬁ ling date, unless the seller and the customer agree on a later deadline. On returning the product (withdrawing from the con-tract) the customer must return any accessories and documents supplied along with the product. The customer does not have the right to keep the defective parts and components of the product re-placed as part of a repair of the product. This shall be without prejudice to any other rights the customer may have in relation to the purchase of the product.
Remark: Complaints against products damaged in transport are governed by the carrier’s complaints procedure.
Manufacturer
Czech Republic
tel.: +420 465 471 433
fax +420 465 473 304
Company ID No. 13216660
email: [email protected]
www: www.my-concept.com