DENVER IOB-207 WiFi Outdoor Smart Camera User Guide
- June 5, 2024
- Denver
Table of Contents
- DENVER IOB-207 WiFi Outdoor Smart Camera User Guide
- User’s Guide for Battery WiFi Camera
- Perform the in-app Setup
- 1. Account Registration and Login
- 2. Add Device
- Settings
- Product Features
- Product Specification Sheet
- 1. Product Design
- Step 1:
- Step 2:
- Step 3:
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DENVER IOB-207 WiFi Outdoor Smart Camera User Guide
User’s Guide for Battery WiFi Camera
Perform the in-app Setup
The app is available for iOS, Android
The app name is “denver smart home
1. Account Registration and Login
Please open “DENVER SMART HOME” App, and enter the App main interface. New
users need to register by Email or Mobile number, click “Register
Follow the steps to complete the registration of the account, and login.
Please log in directly if you already have an account. To input your account and password, click “Log in”.
2. Add Device
Tap + or “Add Device” to add the device. Find the smart camera in
the video surveillance list and click it
Note: The “auto scan” function cannot be supported please select “Add Manually” and follow up below steps to add the device.
Note: Allow to access your location if prompted to enable the GPS.
Please click “I Hear a prompt” if you heard it, then will start connecting.
The camera is added successfully. You can enter the live video interface.
Settings
Click to enter the Settings page. There are only a few settings to make, so then process is quick and easy. To start setting up your camera
Product Features
Product Specification Sheet
1. Product Design
8. Flip Switch
9. AA Battery
10. Power Switch
11. Mirco-SD card
12. Reset button
Step 1:
Install anchors into a stucco, brick or concrete surface. Use the drill bit to drill one hole in your wall and install the anchors. Install the base bracket on the wall.
Step 2:
Please turn the flip switch to “OPEN” and open the cover, then install four pcs AA batteries in it. (Please make sure that the polarity of the battery is correct.) Then put the power switch to “ON” and press the RESET button for 5 seconds. When blue lights light on , the red lights flash slowly, the device is ready to connect to the network. Refer to picture 2.
Step 3:
Align the device to the base bracket and hold it, then adjust the appropriate angle, the installation is finished
- The USB interface is only used for power supply.
- When the mobile phone is connected to the home WiFi router, the mobile APP can generate a QR code that includes the name and password of the WiFi router. The product recognizes the QR code through the lens on the product, and the product is automatically connected to the router and server after identification. At this time, the APP also finds the product through the server, and the APP can control the operation of the product through the network.
If there is no WiFi signal, the product can still be triggered to record with the motion detection signal, and the video file can be viewed through the APP when the WiFi is restored.
Please notice – All products are subject to change without any notice. We take reservations for errors and omissions in the manual.
Electric and electronic equipment contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment) is not handled correctly. Electric and electronic equipment is marked with the crossed out trash can symbol, seen above. This symbol signifies that electric and electronic equipment should not be disposed of with other household waste, but should be disposed of separately.
All cities have established collection points, where electric and electronic
equipment can either be submitted free of charge at recycling stations and
other collection sites, or be collected from the households. Additional
information is available at the technical department of your city.
Hereby, Inter Sales A/S declares that the radio equipment type IOB-207 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformit is available at the following internet address:
www.denverelectronics.com and then click the search ICON on topline of
website. Write model number: IOB-207. Now enter product page, and red
directive is found under downloads/other downloads. Operating Frequency Range
:2412MHz-2472MHz Max Output Power:19db
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>