WITT Sensoric RP 25 Reflective Photo Electric Switch Instructions
- June 13, 2024
- WITT Sensoric
Table of Contents
Electric Switch Instructions
RP 25 Reflective Photo Electric Switch Instructions
- range 0.5…15m, depending on the type of reflector
- immune to external light sources
- high degree of protection
- optional cable entry
- terminal compartment
- polarisation filter optical system
- test input
- operating voltage 10-40VDC or 24VAC ±25%
- protected against power supply polarity reversal
- relay output
- easy adjustment of the optical sensor
- dirt indicator
- LED alignment indication Declaration of conformity
EMC directive 2014/30/EU
EN 61000-6-2 and EN 61000-6-3
Technical data
operating voltage| 10…40VDC
24VAC, ± 25%
---|---
operational| <100ms after power on
current consumption max.| 30mA/24V
type of light| red, 680nm
pulsed, polarised
aperture angle| approx. 1.5° total angle
output| relay, changeover contact
switch rating| min. 1mA/min. 5VDC
max. 0.6A/50VAC
max. 0.5A/48VDC
(resistive load)
response time| <10ms, detection of light
beam interruption
relay delay| when the light beam is
uninterrupted again, the relay
picks up with 100ms delay
type of switching| responsive to brightness, i.e.
the relay picks up when the
light beam is uninterrupted
ranges| R30/60 = 0,5…8m
RD82 SW4 = 0,5…12m
R100/100 = 0,5…15m
indications| dual LED red/green
light beam interrupted| lights up red
light beam uninterrupted,| spare critical function capacity.flashes red at 4Hz
light beam uninterrupted| high spare function capacity.
= lights up green
additional function| test input
(when 0V at terminal 1 the
transmitter switches off)
type of connection| screw terminal max. 1.5mm²
casing material| lower part: ABS-GF15%
upper part: PMMA, red
degree of protection| IP65, to EN60529
operating temp.| -25°…60°C
storage temp.| -35°…80°C
weight| approx. 60g
size| 86x44x39mm³ (LxWxH)
Terminal assignments
Note : For test purposes the photo-electric switch switches the transmitter off when GND is applied to terminal 1. For reasons of safety the photo-electric switch is responsive to brightness, so that the relay picks up when the light beam is uninterrupted.
Size
Note: The cable entry is moulded into the lower part of the casing and can be broken out. Either the rubber grommet or the cable g land (both supplied) can be used.
Fine adjustment
After mounting the photo-switch the light beam can be adjusted using 3 screws.
Important note!
The optical sensor is spring-mounted.
All 3 screws are unscrewed by 1 turn factory-made, the maximum is 3 turns.
The optical sensor is optimally aligned when the green LED lights up
constantly.
LED lights up: 100 % of the cone of light is hitting the reflector LED flashing: Less than 100 % of the cone of light is hitting the reflector
Accessories
|
---|---
HW-LS mounting bracket
for the reflektive photo-electric switch
Material: bright 1,5 1.4301 (V2A)
Ordering details
HW-LS
314847| WSH-RD82 rain cover
for the reflector RD82-SW4
protection against rain, hail and snow,
impact resistant, UV-stable
material: PA6 GF15
Ordering details
WSH-RD82 315316
|
Anti-condensation cover
for RD82 SW4 reflector
ISO RD82
Material: Polystyrene or Neopor
Ordering details
ISO-RD82 314849| HW-RD82 mounting bracket
for the RD82-SW4 reflector
Material: bright 1,5 1.4301 (V2A)
Ordering details
HW-RD82 314848
|
WSH-LS rain cover
for the reflective photo-electric switch RP20/RP25,
protection against rain, hail and snow,
impact resistant, UV-stable
material: PA6 GF15
Ordering details
WSH-LS 315315| Anti-condensation cover
for R30/60 reflector
ISO R30/60
Material: Polystyrene or Neopor
Ordering details
ISO-R30/60 314850
|
Mounting: RD82 SW4 reflector
screwable
Range: approx. 12m with
RP20
Ordering details
RD82 SW4 314811| R30/60 reflector
Mounting: screwable
Range: approx. 8m with
RP20
Ordering details
R30/60 314810
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>