VEVOR K4001 Induction Cooktop User Manual

VEVOR K4001 Induction Cooktop

The information in this handbook is correct at the time of printing. our company is responsible for recising and updating this handbook. However we reserve the right to modify and update our products and handbook without notice.This handbook contains sketches, which are to be used as a reference only.Please use common sense lf these sketches is not exactly your sutuation or products.

CONTROL PANEL

This panel schematic is suitable for 2/3/4/5/6 head furnace series.

SCHEMATIC DIAGRAM OF THE CONTROL PANEL

INSTRUCTION

1. Power: when connected to the power supply, there is a sound of dripping, and all display units shine at the same time for a successful self-test.
2. Power button: pressthe key to drop a sound into standby. power Indlcator lIlght, four furnace area display-. (When there ls no operatlon in the standby state for a short perlod of time, the furnace area – and the power indlcator is no longer dlsplayed, and automatically exits the standby state and returns to the shutdown state. Standby state is shown as follows
3. Heating: For example, if you want to use the upper left furnace area for heating, pressIn standby state, there Is a drop sound and the dlgital display 0 flashing, indicating that the furnace area ls selected succossfully, and theon press the sllding area below the number to adjust the desired fire gear.
   • Power distribution:uppor left 240V/1200W.Olower loft 240V/1500W, Cupper right 240V/200ow.lower right 240V/1200W. (+/-10%)
4. Firepower adjustment: first select the furnace area (such as the left furnace area), when the digital dlsplay flashing, slde or cllck the flgure below, 1 to 9 can be adjusted. Press 0 to stop heating.
5. Child lock: long press the chld lock key for 2-3 seconds to drop a sound to lock or unlock, locked successfully child lock indicator llght on, shutdown or standby with heating state can operate child lock. After successfully lockłng, do not operate any health except child lock. Locked successfully as shown In flgure:
6. TIming: Thls function ls to set the shutdown time. In heating mode, press the tIming button to enter the preset timing. The default time ls 00 mlnutes. According to the +AdJust the time (up and down adjust 1 minuto, long press progresslve 10 minutes, 99 minutes at most), stop the operation after the adjustment, dlgital flashing several times into the steady setting success. Continuously press the timing button to set the time in multiple furnace areas. After the setting is oomplete, the small dot flashes in the lower right corner of the display digital number. The time display in different furnace areas automatically switches to about 10 seconds, with the small dot as a mark. As shown In the plcture, timing left upper furnace area: 99 minutes
7. Pause button: press this button to drop once the Indicator lght is on to pause. heating and keep the current gear display. Press again to resume heating. As shown In figure:
8. Panel high temperature warning: there ls stl resldual temperature on the furnace panel after use, warning display H, be careful of scalding hands.
9. duct dimenslons and precautlons:
   • Product dimensions 770520°85 (30.320.47*3.34 inches)
   • Opening roar size 760 500 150mm (29.92 19.68 5.9 Inche8)

INSTALL ATION EASILY

Note: If the product ls used on the table, because the bottom of the use process will produce temperature, please use high temperature resistant flame retardant material for the table such as marble.. And soon.

SAFETY PRECAUTIONS

This product does not consider the following:
Warning: If the surface ls cracked, turn off the applance to avold possible electric shock.
Use of equipment by unattended young children and disabled children’s play Squipment.

1. Do not overheat an empty pan.
2. Do not carry the inductlon cooker with the appllance loaded.
3. Do not let chlldren operate alone to avold scalding and other rlsk.
4. During the operation of the appllance, the temperature of the black crystal plate and the surface of the applance ls very high, s0 please do not touch It.
5. Do not use It in the bathroom, gas stove and other damp places or near Inflammable and exploslve objects.
6. Metal Objects Knives, forks, spoons and LIDS should not be placed on the surface
7.  cookng area to preventnem rom geting not.
8.  pment, tshould be placed horlzontaly, not close to the wallD not use Deper, Cloth and other articles on the panel to heat Indirectly, so as to avold the high temperature of the bottom of the pot Cause combustion.
9.  Do not directly add canned and other sealed containers, otherwlse the container wll be heated and expanded, resultlng in exploslon.
10. Do not heat the aluminum foll directly or indlrectly.
11. This product ls a household ktchenware, shall not be used in Industrial, medical and other places to use Accldent-free release.
12. Unplug the power cord plug from the socket to avold electronic devices caused by ong me electriciyeces r Bging damage, even ire.
13. After cooking, there ls stll resldual heat on the panel generated by the hlgh temperature of the pot. Do not touch it Immediately.
14.  If the cord is damaged, It must be repaired by the manufacturers maintenance department or Simllar departments of professlonal personnel to ropalr and replace
15.  Do not use POTS and pans with painted bottom on the Inductlon cooker to avold high temperature To burn.
16. Do not heat plastic containers and paper on panels to prevent burning9.
17. Do not hit the black crystal panel with hard objects or touch the black rystal panel with sharp Instruments to avold black orystal Plate cracking and other damage.
18. Do not use the Induction cooker on the carpet or tablecloth, so as not to block the exhaust port or suctlon port, shadow Heat dissipation.
19. Do not heat food directly on the panel, especlally hlgh fat food, overheating oll will
20. The induction cooker cannot be operated by external timer or independent remote
21. Do not place the Inductlon cooker on the iron, stainless stoel, aluminum and other metal panel, because The action of magnetic field line will cause Its heating surface to burn out the bottom of Induction cooker.
22. Do not flush with water directly to prevent the Internal electronic oomponents from water failure.

SAFETY REMINDING

CLEANING AND MAINTENANCE

1. Please shut off the power and pull out the plug before cleaning of the appllance.
2. Clean the appllance until It cools down completely
3. To remove dirt, please select litmusless detergent.
4. After removing dirt, please use neat wet cloth to clean the unit.
5. Do not clean by water directly, water gets Inside may cause malfunction.
6. Keep the ceramic plate and pan clean before cook, otherwise, dirt after charring is very difficult to clean and the plate may get discoloration
7. You may clean alr vent/alr entry’s dirt by vacuum cleaner to suck up, If there ls dirt with all, add a litte litmusiess detergent with toothbrush to clean.
8. Don’t use caustic impregnates to clean. It may damage the cooker by chemical reaction. Do not use benzine, scrubbing brush or polishing powder to clean the Inductilon cooker.

TROUBLE SHOOTING

If there ls anything wrong with the stove, please check it as following before sending to repair.

No indicator light when power “on”

| 1.Cable/terminal block is loose 2.Broken circuit or blown fuse 3.Power supply stopped

2

| If there is “buzz” noise,

and the “on/off “light flash, no heating

| 1.  Please check if the pot is available

2.  lf the pot is in the centre of the ceramic plate

3

|

Appliance suddenly stops heating during operation

0

| 1.Air entrance or outlet blocked 2.Over-heating protection activated

3.Please check if the temperature around is too high 4.If the working time over defaulted working time.or

the timer finish

 | No response for the key| Please check the plug is in right place.

USABLE PANS

All flat bottom pots. Please limit your food within 4kg.

HEAT DIssIPATION STRUCTURE INSTALLATION DRAWING

When the machine is embedded, to ensure the normal use of the machine and better heat dlssipation.
Requirements:

1. 30-50mm heat dissipation shouid be left on the left and right sides and behind.
2. The counter interior should be as large as possible to ensure that enough cold alr ls sucked Into the machine.
3. Inlet alr (cold alr) must be aeparated from outlet alr (hot air) space.
4. The alr Inlet and outlet space of the counter leave alr roar.

Positive renderings

side view

INSTALLATION

Owing ta tha hiah tamnaratura insida tha Infrarad comkar maka surannad vantiatlon ls provided to assure Its normal operation.
As shown In Figure 2 Attention:

1. The electric hob ls recommended to be Installed by professlonal. Please never conduct the operation by yourself.
2. The wall and heating area above the table surface shall withstand heat.
3. To avold danger the ceramic cooker hob must be installed Into the cabinet before use.
4. Appllicable cabinet material:wood, marble resin etc.

MATTERS NEEDING ATTENTION

During operatlon, the surface temperature of the crystal plate ls very high. Please do not touch It to avold scalding.The appllance shall not be operated by means of an external timer or Independent remote control system.

FAULT CODE

• EO: no pot
• E1-The voltage ls lower than 120.
• E2-Excessive voltage (voltage hlgher than 270)
• E3- Furnace surface over temperature or sensor damage short circuit
• E4-Furnace surface sensor open
• E5-IGBT over temperature or fan damage does not work
• E6 The 1GBT sensor Is open
• E8-The control board Is connected to thee main power supply board

POWER SUPPLY INSTALLATION DRAWING

Electrical diagram of the beautiful line (black, white, green E) Thls figure is only for throe-phase power in the United States, and the voltag between two live lines is 240VAC Three core cable machlne connection drawing

Electrical dilagram of the beautiful line (black, white, green E) Thls chart is only applcable to 220 V single-phase power countrles in Europe and China Three core cable machline connection drawing

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>