ETA 4320 Electric Hair Dryer with Ionization Instruction Manual
- June 5, 2024
- ETA
Table of Contents
Electric hair dryer with ionization
eta 4320
Instruction For use
10/12/2013
**SAFETY WARNING
**
- Before the first use, read the instructions for use carefully, look at the picture and keep the instructions for use.
- Check whether the data on the type label corresponds with the voltage in your socket.
- The appliance is intended for use in households only and for similar use! It is not designed for use in hair salons or for similar commercial use!
- Do not use the appliance close to water contained e. g. in containers, sinks, bath tubs, swimming pools, etc.
- Never use the appliance if its power cord or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell into water. In this case, take the appliance to a special service to check its safety and proper function.
- This product can be used by children at the age of 8 years and older and people with reduced physical or mental abilities or lack of experience and knowledge if they are supervised or if they were instructed regarding use of the appliance in a safe way and if they understand possible risks. Children must not play with the appliance. User cleaning and maintenance must not be performed by children if they are younger than 8 year and unsupervised. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
- The dryer must not be sunk in water and it must not be let at places where it could fall into a bath tub or a wash basin. If the dryer fell to water, do not take it out! First of all unplug the power cord from the socket and only then take out the dryer. In this case take the appliance to a specialized service shop to check its safety and proper function.
- If the hair dryer is used in a bathroom, it has to be disconnected from the electric power by unpluging the power cord from the socket because there is risk close to water even if the hair dryer is off.
- If the power cord of the appliance is corrupted, it has to be replaced by the producer, its service technician or a similarly qualified person so as to prevent dangerous situations.
- Before replacing accessories or accessible parts, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!
- Always unplug the appliance from the power supply if you leave it unattended and before assembly, disassembly or cleaning.
- For additional protection, we recommend installation of current protection (RCD) with the nominal release current not exceeding 30 mm. Ask a control technician or an electrician for advice.
- Do not plug or unplug the appliance from a socket with wet hands and do not pull the power cord! Do not insert accessories into any body cavities.
- Do not let the appliance in operation without supervision!
- Do not put the dryer on hot heat sources (e. g. oven, stove, radiator, etc.)
- Any part of the appliance must not get in contact with places sensitive to heat (e. g. eyes, ears, neck, etc.).
- If the dryer was stored at lower temperatures, acclimatize it first, by which you remove the stiffness of the lubricating fat in bearings and the mechanical resistance of the plastic parts will be kept. It is not permissible to adjust the surface of the extra attachment (e.g. self-adhesive paper, foils, etc.)!
- When the appliance is switched on for the first time, short and slight smoke can come out that does not mean any defect and it is not a reason for claiming a defect of the appliance.
- Holes for air ventilation must not be covered. Also, do not put the dryer in the “on” position on soft surfaces (e. g. bed, towels, sheets, carpet), the duct could get covered. Penetration of dust, hair, threads, etc. to the duct has to be prevented.
- Do not insert or throw any objects to the holes.
- Be very careful when handling the adapters during drying (they are hot).
- Disconnect the appliance from the power supply right after use by unplugging the power cord from the socket and let it cool down before storage.
- When the appliance is overheated, the automatic heat fuse is activated and it disconnects the power supply. If it happens, switch off the appliance and unplug it from the socket. Remove possible visible obstacles preventing airflow and let the appliance cool down.
- Do not wind the power cord around the appliance, this will extend life of the power cord.
- If you need to use the extension cord, it has to be uncorrupted and it has to comply with the valid standards.
- Never use the appliance for any other purpose than for the intended purpose described in these instructions for use!
- The producer does not guarantee any loss caused by improper handling of the appliance and its accessories (e. g. electrical accident, fire, burn, hair damage) and its guarantee for the appliance does not apply in the case of non-compliance with the safety instructions above.
DESCRIPTION OF THE APPLIANCE AND ITS ACCESSORIES
A – hair dryer
A1 – air flow intensity regulator
position
position
position| | – off
– medium airflow intensity
– maximum airflow intensity
---|---|---
A2 – air temperature regulator
position
position
position| | – cool air
– medium air temperature
– maximum air temperature
---|---|---
A3 – button (by pressing and holding the button, heating of the outgoing air is interrupted and thus the air temperature is reduced, which enables quick cooling and fixation of hair in the final hair styling)
A4 – handle
A5 – removable suction grid| A6 – hanging loop
A7 – power cord
---|---
B – adapters
B1 – concentrator (used for concentrating air to a specific place)
B2 – diffuser (used for hair styling; close contact with scalp has to be
avoided; otherwise hair can get overdried)
INSTRUCTIONS FOR USE
Remove all packing material and take out the dryer with its accessories. Plug the power cord A7 to a socket. Put the selected adapter B on the dryer.
Hair drying
For quick hair drying, turn the switches A1 and A2 to the position of the
maximum temperature and the maximum airflow. For drying short hair or for
finishing hair drying, set the switches to the lower positions. Direct the
outgoing air to hair while keeping the dryer handle in a distance of 10 to 15
cm from the head and move it evenly. In drying with hot air flow, take out
excessive humidity from hair using a brush or fingers. If you have long hair,
bend your head so that the hair falls down freely from the scalp and face.
After you have finished drying, cool down the dryer by turning the A2 switch
to the cool air position and then turning the A1 switch to the 0 position.
Hair styling
Using diffuser B2 you will add volume to your hair and you will create natural
waves. Turn the A1 and A2 switches to the position of the medium temperature
and the medium airflow intensity. Wind on an air strand using the diffuser and
let the air flow on it for 2 to 5 seconds (the time depends on the structure
and condition of your hair).
MAINTENANCE
Turn off the appliance before each maintenance, unplug the power cord from the power supply and let it cool down! Wipe the dryer surface with a wet soft cloth. Do not use rough and aggressive detergents! Maintenance only includes mechanical cleaning.
Cleaning the grid ()
Hold the grid and pull it out from the dryer. Remove possible impurities from
the grid (e. g. using a brush). After cleaning, put the grid back by the
opposite movement.
ENVIRONMENT
Printed signs of materials used for manufacture, packing, components and accessories, as well as their recycling, are on all the pieces if their dimensions enable it. The symbols on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed of together with municipal wastes. Please, hand them over to the collection points designed for their correct disposal, where they will be accepted free of charge. By correct disposal of this product you can help to preserve valuable natural resources and help to prevent possible negative impacts to the environment and to human health, which could be the results of incorrect waste disposal. For further details ask the municipal authorities or the nearest collecting point. Penalties can be charged for incorrect disposal of such wastes, according to national regulations. If the appliance is to be put out of operation definitely, we recommend cutting off the feeder cable, to disable its use.
Expert service must do the large maintenance or to intervene into inside parts
of the appliance!
Non-observance of the instructions of the manufacturer cancels the right for
guarantee repair!
TECHNICAL DATA
Voltage (V)
Absorbed power (W)
Weight (kg) approximately
Protection class of the appliance
Size of the product (mm)| given on type label
given on type label
0,5
II.
260 x 90 x 240
---|---
Power consumption in off mode is 0.00 W.
The product has received ES declaration of conformity according to Act as
amended. The product matches the requirements of the below statutory order as
amended.
– Committee Regulation No. 2006/95/ES as amended, setting the technical
requirements of the electrical appliance as low.
– Committee Regulation No. 2004/108/ES as amended, setting the technical
requirements of products in terms of their electromagnetic compatibility
The manufacturer reserves the right to make insignificant changes to the
standard design that do not affect the function.
Do not use the appliance close to bathtubs, showers, bash basins or other
water containers.
The guarantee certificate is valid only for the Czech Republic and the Slovak Republic.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>