eta 6762 Atmos II Vacuum Sealer User Manual

June 5, 2024
ETA

6762 Atmos II Vacuum Sealer
User Manualeta 6762 Atmos II Vacuum Sealer


Optional accessories

eta 6762 Atmos II Vacuum Sealer - figure 1| eta
6762 Atmos II Vacuum Sealer - figure 2
---|---
eta 6762 Atmos II Vacuum Sealer - figure 3

Product images are for illustrative purposes only

Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep these instructions including the warranty, the receipt, and, if possible, the box with the internal packing.

GENERAL SAFETY INSTRUCTIONS

GENERAL PROVISIONS:

  • Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.

  • Check whether the data on the type label corresponds with the voltage in your socket.
    The power cord plug may only be connected to the electrical socket complying with the applicable standards.

  • This appliance may only be used by children aged 8 years or older, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children younger than 8 years must be kept out of reach of the appliance and its power cord.

  • Do not leave the appliance running without attendance and check it during the whole process of welding!

  • Before replacing accessories or accessible parts, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!

  • Always unplug the appliance from the power supply If you leave it unattended and before assembly, disassembly or cleaning.

  • Never use the appliance if the power cord or power plug is damaged, if the appliance is not correctly operating or if it has fallen on the floor and been damaged, or if it has fallen into the water.

  • In such cases take the appliance to a professional service center to verify its safety and correct function.

  • Pay careful attention when handling the appliance to avoid injury, (e.g. burns).

  • The appliance has a hot surface. Persons insensitive to heat must be careful when using the appliance.

  • When the appliance is in operation, prevent pets, plants or insects from getting in contact with it.

  • The appliance is intended for home use and for similar purposes (in shops, offices, and similar sites, in hotels, motels, and other residential premises, or in facilities providing bed and breakfast service). It is not intended for commercial use!

  • Do not plug the power cord in the electrical socket and do not unplug it with wet hands or by pulling the power cord!

  • Never immerse the appliance into water or any other liquid (even its parts)!

  • Avoid contact with the sealing wire when hot.

  • The producer does not undertake any responsibility for damage caused by improper use of the appliance (e.g. deterioration of food, injury, burning, scalding, fire, etc.) and its guarantee does not cover the appliance in the case of failure to comply with the safety warning above.

USE OF THE APPLIANCE:

  • After completion of the vacuum, the process leaves the cover of the appliance open for the welding part to cool down.

  • CAUTION – The appliance is not designed for constant operation.
    Do not use the welder constantly for longer than 15 minutes, then leave it to cool down for approx. 10 minutes.

  • It is not intended for outdoor use.

  • The appliance must not be used in damp or wet environments and in any environment with the danger of fire or explosion (spaces where chemicals, fuels, oils, gases, paints, and other flammable or volatile materials are stored).

  • Do not seal fluids in a liquid state with a vacuum function. If you want to store liquid food (such as soups), first freeze the food in an appropriate container, cut the food into pieces, put it in bags, and seal/vacuum them. Put the individual bags into the freezer.

  • Do not place the appliance on unstable, fragile, or flammable surfaces (e.g. glass, paper, plastic, wooden varnished boards, and various fabric/table cloths).

  • Use the appliance in the working position only at places with no risk of turning over and at a sufficient distance from heat sources (e.g. heater, stove, cooker, oven, grill),  flammable objects (e.g. curtains, drapes, etc.), and wet surfaces (e.g. sinks, wash basins, etc.).

POWER CORD:

  • If the power cord of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician, or a similarly qualified person so as to prevent dangerous situations.
  • Never put the power cord on hot surfaces and never let it hang over table edge or worktop edge. If the cord is caught or pulled, e.g. by children, the appliance may overturn and fall down, causing a serious injury!
  • The power cord must not be damaged by sharp or hot objects, or open fire, it must not be sunk into water or bent over sharp edges.
  • In order to ensure the safety and proper function of the appliance, use only original spare parts and accessories approved by the manufacturer.
  • Only use this appliance for the purpose it was designed for, as specified in this manual.
    Never use the appliance for any other purpose.

DESCRIPTION OF THE CONTROLS

A – bag sealer body
A1 – lid
A2 – removable container for ATMOS IIted fluid
A3 – welding part
A4 – the sucking area
A5 – sealing gasket
A6 – airproof loop of sponge
A7 – port for external extraction
A8 – space for cable storage
A9 – power cable

B – control panel
B1 – STOP button
B2 – sealing button
B3 – operation light indicator
B4 – vacuuming + sealing button
B5 – external vacuum + marinate button
B6 – button for selecting the type of food
B7 – signal lights for the selected type of food
B8 – button for setting the vacuum-packing intensity
B9 – signal lights for the selected vacuum-packing intensity

C – extraction hose
D – vacuum-packing box
D1 – release valve

Optional accessories:
Cling film: 3m long and 28cm wide – ETA176200010
Bags 30 x 40 cm (50 pcs) ETA176293040
Bags 25 x 35 cm (50 pcs) ETA176292535
Bags 20 x 30 cm (50 pcs) ETA176292030

Suction hose + Hose adaptor ETA076290020, intended for:
Reusable bags 10 pcs 23×21 cm; 10 pcs 23×28 cm; 5 pcs 30×28 cm ETA176290025
Vacuum-packing box (1x 670 ml + 1x 1360 ml) ETA076290030
Vacuum-packing box (1x 1000 ml + 1x 2000 ml) ETA076290040
Vacuum-packing box (1x 1350 ml + 1x 2570 ml) ETA076290050
Vacuum-packing box (2x 670 ml + 2x 1360 ml + 1x 1000 ml + 1x 2000 ml) ETA076290060

Note: the above boxes cannot be used for the marinating function
Extraction hose – ETA476200210, intended for:
Vacuum-packing box (capacity: 1000ml) – ETA476200200
Vacuum-packing box (capacity: 2000 ml) – ETA476292000

INSTRUCTIONS FOR USE

Remove all packaging materials and take out the appliance. Remove all adhesive foils, stickers or papers from the appliance.
BAG SEALER FUNCTIONS

  1. B8 button for setting the vacuum-packing intensity
    It is used to set the vacuum-packing intensity. The selected mode is indicated by the appropriate indicator B9:
    = Normal (faster extraction for normal vacuum-packing)
    = gentle mode (slower extraction for vacuum-packing of more fragile food)

  2. B6 button for selecting the type of food
    It is used to set whether you wish to vacuum-pack dry food or moist food.
    The setting is indicated by the appropriate indicator light B7:
    = dry food
    = Moist food

  3. External vacuuming + marinating button B5 (vacuuming in the vacuum box)
    The button supports two basic functions:
    a) Evacuation of air from the vacuum box (short press, button backlight illuminates) It is used to extract air from the vacuum box using the suction hose. When activated, it sucks the air out of the vacuum box.
    b) Marinating function (long press to activate, button backlight flashes) Vacuuming opens the pores of the ingredients, thus considerably speeding up the marinating process from several hours to approx. 20 minutes. The program works in cycles in which it gradually extracts and releases air. The program is designed to work with the vacuum box D (ETA476200200 and ETA476292000).
    Press button B5 after connecting the hose to the external suction opening and then plugging it into the vacuum box. After switching off, remove the suction hose (first from the vacuum box).
    Note
    If you have purchased ETA boxes with an adapter (ETA076290020), its use is slightly different – you insert the thin connector into the device itself and just attach the extended circular part to the given suction point of the box or compatible bag – when the function is activated, the circular part will attach itself.
    Caution
    The correct function of the appliance is guaranteed only if you use the vacuum-packing boxes supplied by the manufacturer. Request the vacuum-packing boxes from your
    distributor.
    – When removing food from the vacuum-packing box, make sure to release the vacuum
    first by pressing down the valve D1 in the middle of the cover.

  4. Vacuum-packing + sealing (B4 button)
    When this feature is activated, the vacuum sealer will remove air from the vacuum bag first (extraction area) and then produce a strong, seamless seal. This operation is indicated by the signal lights B4 and B2. Place the bag as indicated in Fig. 3B.

  5. B2 sealing button
    When activated, the vacuum sealer will produce a strong, seamless seal. This operation is indicated by the signal light B2. Place the bag as indicated in Fig. 3A.

  6. B1 STOP button
    It is used to stop the activated operations B2, B4, and B5.

Standard operation
Connect the appliance to the mains. Set the vacuum-packing intensity and the type of food according to the selected ingredient. Follow the instructions provided in Fig. 2:

  1. Open cover A1.
  2. If you are making a bag from a bag roll (both ends are unsealed), prepare and cut it to the desired length first. Then place one end of the cut part on the welding seal A5  and weld with the button B2. Fill the bag with the required raw material, and insert the end of the bag into the extraction area.
  3. Close the lid A1 and push slightly on the edges of the lid, after activating some function the lid will clamp and close itself.
  4. Press the button with the desired function (B2, B4 or B5). The operation of the function is indicated by the light signal B3 and the illumination of the button.
  5. When the corresponding indicator light goes out, the function is complete. The lid releases itself by releasing the air – then you can open the lid and remove the foil/bag.

Notice

  • If the function is interrupted during operation (e.g. by a power failure), the lid may remain locked. Alternatively, the lid may not be able to be closed as the lid locks remain in the locked position. In this case, restart the appliance and try to activate the suction function for a while, and then interrupt it.
  • Proper functionality of the appliance is assured only when using the foils/bags supplied by the manufacturer. Request these foils at your retailer. Do not use plastic bags. At the same time, you can re-weld many foods in their original packaging (eg bags of potato chips).
  • The vacuum sealer is used to seal cling foil up to the max. width of 300 mm.

CARING FOR YOUR VACUUM SEALER

Do not clean the appliance if is hot. After each use, wipe the outer parts with a damp soft cloth.
To clean the inner parts of the appliance, wipe all pieces of food and liquids with a paper cloth. Leave to dry properly before next use. Do not use abrasive and aggressive cleaning agents! If the power cord becomes stained, wipe it with a damp cloth. The color change of the surface in time is normal. This change does not change the qualities of the surface in any way and is not a reason to return this appliance! If particles of plastic adhere to the sealing wire, wipe them off carefully to avoid damage to the wire. If can help to carry out a sealing operation the lid and pressing fully down without a bag in position. This will heat the wire and soften any plastic adhering to it.

BAGS
Before reusing a bag, we recommend properly washing it in warm water with a small amount of dishwasher detergent, and rinsing in clear water. Place the bag so that water can flow out from inside the bag. Before reusing, dry the bag thoroughly.
VACUUM-PACKING BOX
Rinse the vacuum-packing box and parts thereof with water and detergent (or wash them in a dishwasher). Allow all the parts to dry out properly before the next use or storage.
Removable container for drained liquid A2
In case of extraction of wet food, check the container after use. If dirty, remove it, pour out the contents and clean the container in warm water with added detergent.

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for the production of packing, components, and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be taken over free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authorities or in the nearest collection site. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations.
If the appliance is to be put out of operation for good, after disconnecting it from the power supply we recommend cutting off the power cord and thus it will not be possible to use the appliance again.

Expert service must do the large maintenance or intervene in inside parts of the appliance! Non-observance of the instructions of the manufacturer cancels the right to guarantee repair!

TECHNICAL DATA

Voltage (V) shown on the type label of the appliance
Absorbed power (W) shown on the type label of the appliance
Weight (kg) approximately 2
Protection class of the appliance II.
CZ 405 x 175 x 90
Size, (mm):

Input in standby mode is < 0,50 W
The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING, OR IN THE INSTRUCTIONS MANUAL: SK

HOUSEHOLD USE ONLY; DO NOT IMMERSE IN WATER OR OTHER LIQUIDS;
TO AVOID THE DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS,  CARRIAGES, OR PLAYPENS. THIS BAG UPOZORNENIE: HORÚCI POVRCH IS NOT A TOY.
WARNING: HOT SURFACE

© DATE 30/9/2021
e.č.08/2021

Documents / Resources

| eta 6762 Atmos II Vacuum Sealer [pdf] User Manual
6762, Atmos II, Vacuum Sealer, Atmos II Vacuum Sealer, 6762 Atmos II Vacuum Sealer
---|---

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals