SEALEY ADT200 200KG Transmission Cradle Instruction Manual
- June 5, 2024
- SEALEY
Table of Contents
SEALEY ADT200 200KG Transmission Cradle Instruction Manual
1. SAFETY
2. INTRODUCTION
Fully adjustable saddle with forward, backward and side-to-side tilt. Suitable for jacks with a 31-33mm saddle spigot pin. Note: When using this cradle, the maximum capacity of the jack and saddle combination will be limited to the lowest specified capacity in the combination e.g. 3000CXD and ADT200 – maximum capacity will be 200kg.
3. SPECIFICATION
Model No: ……………………………………………………….. ADT200
Capacity:……………………………………………………………. 200kg
Compatibility: ………………………………………………….3000CXD
4. ASSEMBLY
Refer to Parts list
WARNING! Failure to assemble the cradle correctly may result in serious
damage and/or personal injury.
-
4.1. Unpack the product and check contents against the parts listed. Should there be any damaged or missing parts contact your supplier immediately.
Note: Items (2, 3, 4, 6, 10, 11) and (1, 5, 4) are pre-assembled. -
4.2. Remove one nut (10) from screw rod (6), and thread screw rod (6) through adjustment pin (5), re-fit nut (10).
-
4.3. Position saddle base (1) underneath saddle plate (2) and thread pivot shaft (12) through from one side ensuring a collar (7) is inserted either side of the saddle base (1) and inside of the saddle plate brackets. Secure with a retaining ring (13) at each end of pivot shaft (12). The three nuts (10) should be positioned near the end of the screw rod (6) closely fitted either side of the shaft (5) and locked onto the screw rod (6) by tightening the screws (11).
-
4.4. Attach saddle angle brackets (14) to the saddle plate (2) with long bolts (15), washers (16) and nuts (17).
-
4.5. Attach saddle angle plates (19) to saddle angle brackets (14), using bolts (20), washers (18) and nuts (17).
-
4.6. Attach chain (27) to one saddle angle plate (19) with bolt (21), washer (22) and nut (23).
-
4.7. Attach hook pin (24) to one saddle angle plate (19) with washer (18) and nut (17).
-
4.8. Attach hook screw (25) to the hook pin (24) with washer (22) and wing nut (26).
5. OPERATION
- 5.1. With the jack fully lowered, remove existing fixed saddle from jack and fit the ADT200 in it’s place. Secure it with nut (9) and washer (8).
- 5.2. Adjust the pitch and tilt of the saddle to assist in safely supporting and transporting the transmission unit.
- 5.3. The cradle may be tilted forwards, backwards and from side to side, by operating the screw rod (6) and/or by turning the cradle on the jack saddle.
- 5.4. Always position saddle angle brackets (14) and saddle angle plates (19) to best support and locate the transmission, ensure all nuts and bolts are retightened. Before moving jack and transmission, ensure that restraint chain is in place and tensioned.
- 5.5. Periodically lubricate the cradle pivot points and the adjusting bolts.
ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>