FLASH F7100322 LED Par 36 12W RGB Light and DMX Controller User Manual
- June 5, 2024
- FLASH
Table of Contents
FLASH F7100322 LED Par 36 12W RGB Light and DMX Controller
INTRODUCTION
THANK YOU FOR PURCHASING LED PAR 36 12W RGB. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.
SAFETY INFORMATION
- Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
- Unpack and check carefully there is no transportation damage before using the fixture.
- Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
- It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
- Disconnect main power before servicing and maintenance.
- Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
- Maximum ambient temperature is: 400C Don’t operate it where the temperature is higher than this.
- In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
- Do not connect the device to any dimmer pack.
- Do not touch any wire during operation and there might be a hazard of electric shock.
- To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
- The housing must be replaced if they are visibly damaged.
- Do not look directly at the LED light spot while the fixture is on.
WARNING!
PRODUCT INFORMATION
- Light source: 12pcs x 3W LEDs
- Power supply: AC 100V/240V 50/60Hz,
- Power Consumption: 40W
- Signal: DMX 512
- Housing: ABS
- 3-Pin XLR DMX input/output
- Net Weight: 0,6kg
- Dimensions: H(12)xW(12)xD(8,9) cm
- Package: Carton Box
INSTALLATION
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.
CONNECTION
The device is equipped with the following interfaces:
- DMX (in/out): XLR 3(5)-pin socket
- Power (in/out): powerCON socket
Connecting DMX signal
The connection is performed using cable with XLR-female -> XLR-Male plugs.
CAUTION! At the last fixture, the DMX signal has to be terminated with a
terminator. Solder a 120Ω resistor between signal (-) and signal (+) into a
XLR plug and plug it in the DMX output of the last fixture.
Voltage specification
| Input Voltage | Total Power | Frequency |
|---|---|---|
| 100-240V | 40W | 50/60Hz |
Connecting power supply
The connection is performed using power cable with PowerCon connector
(included). The device must be operated by qualified personnel.
Make sure that the power grid supply parameters are consistent with device
parameters and limitations are not exceeded.
CAUTION! In the case of cable damage do not attempt to repair.
Replacement or repair can be made only on the manufacturer or by a person with
appropriate permissions.
Using lamp, the change rate of power voltage should be within ± 10%, if the
voltage is too high, it will shorten the light’s life; if it’s not enough, the
lamp will be dark. Please restart it after turning off light for 20 minutes
until full-cooling. Frequent switching will reduce the life span of lamps and
bulbs; intermittent using will improve the life of bulbs and lamps.
DMX CHANNELS
| Mode | Value | Description |
|---|---|---|
| DMX | d001-d512 | 8 channels DMX mode to select the starting address |
| Master/Slave | IP.01-IP.64 | Master/Slave (64 units maximum) |
| Static Color | A1.01-A1.10 | Select the LED position |
| Auto Program | A2.01-A2.32 | Adjust hopping speed (slow to fast) |
Fade Mode
| A3.01-A3.19
(Press ENTER to turn the below value)
|
A3.01-A3.32| Adjust hopping speed (slow to fast)
Sound Active Mode
| A4.01-A4.19
(Press ENTER to turn the below value)
| ****
Select sound-active program
A4.01-A4.04| Adjust sound-activated sensitivity
Strobe Mode
| A5.01-A5.19
(Press ENTER to turn the below value)
| ****
Select the LED position
A5.01-A5.32| Adjust strobe speed (slow to fast)
Static Color Dimmer
| r000-255| ****
Adjust the brightness of different LED position
g000-255
b000-255
U000-255
CH| Function| Value| Description
---|---|---|---
1
| No Function| 0-10|
Static Color| 11-50| + CH2 to Select LED Position
Auto-Play| 51-100| +CH3 to Adjust Speed
Fade| 101-150| +CH2 to Select LED Position
+CH3 to Adjust Speed
Sound-Active| 151-200|
Strobe| 201-255| +CH2 to Select LED Position
+CH3 to Adjust Speed
2| Different LED Position| 0-255|
3| Speed Adjustment| 0-255| Slow to Fast
4| Dimmer for 5-7 CH| 0-255| ****
0-100%
5| Red| 0-255
6| Green| 0-255
7| Blue| 0-255
8| empty| 0-255
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>