EARPHONE CONNECTION MOTOROLA APX 8000 Air Pro Wireless PTT Combo Kit Instruction Manual
- June 3, 2024
- EarPhone Connection
Table of Contents
- EARPHONE CONNECTION MOTOROLA APX 8000 Air Pro Wireless PTT Combo Kit
- TO CONNECT WIRED HEADSETS
- MANUFACTURER’S LIMITED WARRANTY
- AIR PRO WIRELESS PI I COMBO KIT FOR MOTOROLA APX 8000 INCLUDES:
- USE WITH YOUR ALL YOUR FAVORITE WIRELESS EARBUD BRANDS
- PAIRING INSTRUCTIONS:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EARPHONE CONNECTION MOTOROLA APX 8000 Air Pro Wireless PTT Combo Kit
TO CONNECT WIRED HEADSETS
- Make sure the Bluetooth microphones are off.
- Hold the microphone cable above the arrow alignment mark.
- Align with arrow on the adapter then click into place.
- To remove, pull up on the spring-loaded cylindrical metal below the arrow on the cable.
- Note: When Bluetooth slide switch is in the “Off” position, no Bluetooth device can be used. This is effective if you want to use the radio with no microphone attached. In this state you can transmit and receive through the radio.
- Leave the Bluetooth switch in the “On” position to use the Wireless PTT unit.
Note: Not compatible with Motorola Radios using Built-In Bluetooth.
Note: When Bluetooth slide switch is in the off position no Bluetooth
device can be used. This is effective if you want to use the radio with no
microphone attached. In this state you can transmit and receive through the
radio.
Leave the Bluetooth switch on to use the Wireless PTT unit.
MANUFACTURER’S LIMITED WARRANTY
Your Sales Receipt is required to validate & obtain warranty services.
Your EPC product is warranted against internal defects in material or
workmanship. All of our earphones are warranted for 12 months. Hygiene
restrictions prevent us from extending our limited warranty to wearable parts
such as: fin Ultra'” ear tips, ea rm olds, clear tubes & ear inserts.
The warranty is extended to the original purchaser only and does not cover the
following:
-
- Physical abuse
-
- Improper maintenance of unit
-
- Damage from tugging or pulling
-
- Frayed, torn or exposed wires
-
- Crushing or smashing in any way, shape or form
General misuse of the item such as: Excessive voltage, tampering with the unit or repairs attempted by someone other than the manufacturer will void the MANUFACTURER’S LIMITED WARRANTY.
The manufacturer reserves the right to evaluate & refuse warranty based on
their evaluation. In order to obtain warranty services, proof of purchase must
be returned along with the product.
For Returns Dept. & Return Authorization# Calpol Free:
888-372-1888.
After calling, send your return along with your name address & Return
Authorization number to:
- The Earphone Connection, Inc.
- 25139 Avenue Stanford
- Valencia, CA 91355
Earphone Connection, Inc. products are designed to produce a specific audio
output level at maximum rated power. Modifying these devices in any way
including adding or removing components and accessories may change the audio
output of the device and could result in PERMANENT HEARING DAMAGE.
Many countries have regulations defining the amount of noise that an
individual can be subjected to during a normal workday. Compliance is
application-dependent and standards vary. It is the SOLE RESPONSIBILITY of the
end user to determine applicability and compliance to local hearing protection
regulations.
Earphone Connection, Inc. strongly recommends that the radio is off before
installation of audio accessory. Once audio accessory is securely installed
radio can be turned on. Radio volume switch is recommended to set at low
position and adjusted once radio is turned on.
AIR PRO WIRELESS PI I COMBO KIT FOR MOTOROLA APX 8000 INCLUDES:
USE WITH YOUR ALL YOUR FAVORITE WIRELESS EARBUD BRANDS
Wireless Earbuds Not Included.
To charge BTR connect the USB to a USB charging port. Charge time 3-4 hrs. BTR is fully charged when LED is solid Red. Full charge should last 20-30 hrs. depending on use.
PAIRING INSTRUCTIONS:
-
STEP 1. Attach Bluetooth radio adapter to radio. Attach top first then bottom with set screw.
-
STEP 2. Use the tip of your finger & press down on the radio adapter PTT button while turning on the radio with your other hand at the same time. Hold for about 20 seconds then release. The LED on the adapter PTT button should start flashing Blue/Red. Now the adapter is in pairing state. If this does not happen, turn off the radio and repeat this step.
-
STEP 3. Follow the pairing instructions for your earbuds & pair to the radio adapter. When radio adapters LED light turns solid Blue, pairing is complete. Insert earbuds to your ears.
Note: You may want to read how to manually pair your earbuds before starting the pairing process, so the radio adapter does not time out. -
STEP 4. With the earbuds inserted, turn off the radio. Wait a beat then turn the radio back on. The earbuds should automatically pair without the need to hold down buttons. You will know this because there should be a pair prompt in your ears and the radio adapter LED will turn solid Blue.
-
STEP 5. With the radio on & the earbuds in your ears, wait a few beats for the radio & earbud to cycle through. Now you are ready to link the finger remote switch. The switch should come pre-paired to the radio.
-
STEP 6. Hold down the PTT button on the remote switch until first LED light appears the release. Wait for about 10 seconds for the remote switch to link to the radio adapter. Now press and hold the switch to communicate, release to listen. When pressing the remote switch, the radio adapter LED should turn Red. You are now completely linked and ready to use.
Next time you use follow these steps:
- Step 1 : Insert earbuds.
- Step 2: Turn on radio, wait for radio and earbuds to cycle. Radio adapter will turn solid Blue.
- Step 3: Power up finger remote switch by pressing and holding the remote switch PTT button until first LED appears the release. Wait about 10 seconds to cycle. Now you are ready to use.
Note: Insert both earbuds to ears to ensure a solid connection, then take one out and use one at a time to conserve earbud battery life if you choose.
To power down kit:
- Step 1: Turn off radio.
- Step 2 : Place earbuds back into case.
- Step 3: Wait for remote switch LED to flash Blue. Press, and hold remote switch PTT button until LED flashes Red.
Note: If radio power is off and you forget to power down finger switch, the switch will power down automatically in about 10 minutes.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>