ROSCO 5500K Image Spot User Guide
- June 4, 2024
- ROSCO
Table of Contents
- INTRODUCTION
- IMPORTANT SAFEGUARDS
- UNPACKING
- INSTALLING LENS TUBE
- IP40 WIRING
- MOUNTING
- GOBO PROJECTION
- FOCUSING
- DIMMING CONTROL
- DMX OPERATION
- DMX ADDRESSING
- DALI OPERATION
- DIFFUSION FILTERS
- DICHROIC COLOR FILTERS
- ACCESSORIES
- ORDERING GOBOS & PERMACOLOR FILTERS
- TECHNICAL SPECIFICATIONS
- 3-YEAR LIMITED WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
5500K Image Spot
User Guide
INTRODUCTION
Congratulations on your purchase of a Rosco Image Spot projector. Designed to
provide crystal-clear imaging and spot illumination, the Image Spot is quick
and easy to set up with convenient push button dimming, remote DMX/DALI
controls, or easy to configure 0-10V dimming options. Image Spot is available
in durable indoor IP40 and outdoor IP65 versions.
To ensure efficient and safe operation, please take a few moments to read this
manual completely.
IMPORTANT SAFEGUARDS
The symbols below are used throughout this manual to identify important safety information. Heed all warnings and safety information.![ROSCO 5500K Image Spot
- warning](https://manuals.plus/wp-content/uploads/2022/08/ROSCO-5500K-Image- Spot-warning.jpg)
PREVENTING ELECTRIC SHOCK
This machine uses mains electrical power at 100-277VAC nominal. When directly
contacted, such voltages are hazardous to human life. Follow all local
electrical codes and take precautions when using this product. This product is
designed to operate from three-wire power systems, where one of the wires is a
safety ground. DO NOT disconnect the safety ground, or use extension cords or
adapter plugs to connect this machine to a two-wire system. Operation without
a safety ground may result in hazardous electrical shock. Use only extension
cords that are of appropriate length and are rated for Image Spot’s specified
voltage and current. If an extension cord shows signs of wear or gets warm to
the touch, discontinue its use and obtain a cord with a higher current rating.
Improper extension cords are hazardous and may result in poor performance due
to excessive voltage drop.
Disconnect the unit from the power source before servicing and when not in
use.
MAINTAINING SAFE OPERATION
Do not look directly into the Image Spot projector. Prolonged exposure to the
light beam can cause damage to eyesight.
Use only Rosco spare parts and accessories so as to not void the product
warranty.
The Image Spot’s surface temperature can approach 184ºF (84ºC) during
operation. Keep minimum 4 inches (10cm) distance away from flammable
materials/objects. Contact with the fixture during, or immediately following,
the operation may result in burns.
Allow the unit to cool before attempting to service.
Rosco Image Spot must only be serviced by a qualified technician.
Rosco Image Spot is not certified for use in hazardous locations.
Rosco Image Spot is designed for operation within the range of -13° to 104°F
(-25° to +40°C); Image Spot HT is designed for operation up to 122°F (+50°C).
Ensure Rosco Image Spot is stored within the range of -4° to 140°F (-20° to
+60°C).
WARNING: Do not look directly into the UV light during operation. Eye and
skin exposure to UV light can cause severe damage to humans and animals. Take
every precaution to limit exposure to UV light (including the use of UV-
blocking eye protection).
UNPACKING
Carefully remove the unit from the box.
Do not attempt to operate the Rosco Image Spot projector if there are any
signs of physical damage. In case of damage, contact your local Rosco dealer.
Your Rosco Image Spot projector requires that an Image Spot focusing lens tube
(purchased separately) be inserted into the opening on the front of the unit
prior to operation.
Five lens options are available, providing Very Narrow, Narrow, Medium, and
Wide beam angles. The size of the image or the beam angle can be adjusted by
replacing the lens tube with an alternate size:
Item No. 296000010009 | Very Narrow 10º |
---|---|
Item No. 296000010019 | Narrow 19º |
Item No. 296000010025 | Medium 25º |
Item No. 296000010030 | Wide 30º |
INSTALLING LENS TUBE
IP40 Units: Insert the small diameter end of the lens tube into the opening on
the front of the projector.
IP65 Units: Slip the 2 provided O-rings onto the grooves on the back end of
the lens tube. Gently insert the end of the lens tube with O-rings into the
opening on the front of the projector.
IP40 WIRING
Your Rosco Image Spot projector will arrive with an unterminated power cord attached to the unit. Wiring to an appropriate connector (not included with Image Spot purchase) or to line voltage should be performed by a qualified electrician and is the responsibility of the installer or end user. The power cord wiring code is as follows:
Core No1: | Live (Hot) Lead |
---|---|
Core No2: | Neutral Lead |
Core No3: | Push DIM |
Green/Yellow: | Ground |
Ensure the correct power connections have been made to the Image Spot projector. The fixture will immediately illuminate upon receiving power.
Your IP rated Rosco Image Spot projector will arrive with an unterminated hybrid power/data cord attached to the unit. Wiring to an appropriate connector (not included with Image Spot purchase) or to line voltage should be performed by a qualified electrician and is the responsibility of the installer or end user. The power cord wiring code is as follows:
18AWG (41/34)|
---|---
Core No1:| Live (Hot) Lead
Core No2:| Neutral Lead
Core No3:| Push DIM
Green/Yellow:| Ground
26AWG (7/37)|
---|---
Core No4:| DMX-/DALI1/0-10V Signal
Core No5:| DMX+/DALI2/DIM+
Core No6:| DMX+(out)/NC
Core No7:| DMX-(out)/NC
Ensure the correct power connections have been made to the Image Spot projector. The fixture will immediately illuminate upon receiving power.
MOUNTING
The Image Spot projector can be installed in the desired location via the center hole in the yoke. Adjust pan as required. Adjust and fix the tilt of the projector via (1) the knurled thumb knob or (2) the optional hex screw (supplied with Image Spot) on the side of the yoke.
GOBO PROJECTION
Prior to operating the Image Spot projector insert an Image Spot gobo into the gobo cassette located on the underside of the fixture. Gobos with logos or other-oriented graphics should be inserted upside down and backward for proper projection. Check to ensure the gobos are free of dust, fingerprints, and other residue prior to inserting the cassette into the accessory slot. Be sure to tighten the thumb screws on the gobo cassette after re-inserting to maintain protection from dust and moisture. A flat-tipped screwdriver should be used for additional torque* to tighten the thumb screws. For optimum image quality, use Rosco Image Spot gobos, which feature custom bezels that fit securely inside the Image Spot gobo cassette.
To avoid the possible ingress of dirt and moisture, orient the Image Spot
projector with the gobo cassette on the underside of the unit and only replace
the lens assembly and gobo cassette when the unit is fully dry.
*Recommended to be tightened to 4Nm min.
FOCUSING
Adjust the coarse focus of the unit by moving the lens tube inward/outward
from the projector. The fine focus can be adjusted by rotating the lens tube
clockwise or counterclockwise.
Due to the ultra-clear optics of the Image Spot projector, it is advised to
keep the optic path clean of dust and debris. Use a non-abrasive microfiber
cloth with Rosco Lens Cleaner to clean the Image Spot lenses and any glass
gobos or Permacolor dichroic glass filters you may have installed.
DIMMING CONTROL
The Rosco Image Spot projector offers four modes of control: Push DIM operation, user-supplied DMX512 data, 0-10V dimming, or DALI controlled.
PUSH DIM OPERATION
The Push DIM option is an easy and effective way to adjust the Image Spot
projector for smaller installations without the need for a DMX/DALI controller
or control system. To operate, you just need to connect a simple push-button
controller to the projector to enable light dimming and a reliable memory
function.
Dimmer control
- On/Off: short press
- Stepless dimming: long press
- The dimming direction is changed with each long press
- Memory: projector levels will be stored at the last level set.
DMX OPERATION
Image Spot projectors are configured for DMX In/Out control. When the fixture
recognizes a valid DMX signal, control of the unit will default to DMX. An
interruption of the DMX signal will cause the Image Spot projector to revert
to the last acquired output setting.
IP40 units have an RJ45 DMX connector on the rear panel. Pin assignments are:
Pin #| Assignment| Pin #| Assignment| Pin #|
Assignment
---|---|---|---|---|---
1| DMX In Data +| 4| DALI 1| 7| OV
2| DMX In Data –| S| DALI 2| 8| OV
3| DMX Out Data +| 6| DMX Out Data –| |
IP65 units are supplied with a factory-installed 2m length of hybrid mains/DMX cable that features a waterproof gland. The DMX wire assignment for IP65 units are:
Wire Color | Assignment | Wire Color | Assignment |
---|---|---|---|
Red | DMX In Data + | Black | DMX Out Data – |
Black | DMX IN Data – | Shield | Ground |
White | DMX Out Data + |
DMX ADDRESSING
A single channel is required for output intensity control via DMX. In order to
set the DMX address, an RDM configuration tool or RDM lighting control device
may be used. If your unit has a serial number preceding 202974 (IP40) or
203012 (IP65) please follow the instructions below:
In order to set the DMX address, an optional DMX Programming Cable (sold
separately) is needed, as well as the free Image Spot Addressing Software that
can be downloaded at
www.rosco.com/ImageSpot
IP40 units require a USB to RJ45 Programming Cable; IP65 units require a USB
to RS485 Programming Cable accessory (both sold separately). Plug the USB
connector into the computer running the Image Spot Addressing Software.
Connect the output end of the cable to either the RJ45 connector (IP40 units)
or use the multi-pin RS485 terminal block to connect to the bare ends of the
IP65 Image Spot DMX cable using the following terminal assignment:
| Programming Cable| Image Spot DMX Cable
---|---|---
Terminal 1 Data +| Brown/Orange| Blue
Terminal 2 Data –| Green/Yellow| Orange
Terminal 3 Ground| Black| Shield
Follow the prompts from the software to set the DMX address (set value). The output of the unit can also be tested by entering a value between 255 (100%) and 1 (0%). Enter a value between 255 and 1, and observe that the fixture output changes briefly before returning to 100%. The fixture should be power cycled Off/On in order to properly respond to the newly programmed DMX address.
DALI OPERATION
The DALI Control option makes it possible to control the Image Spot projector
using a DALI or lighting control management system. The bi-directional
protocol allows feedback from the Image Spot on different aspects and enables
the unit to be controlled and set individually. The DALI protocol limits the
number of DALI devices to 64. IP40 units have an RJ45 connector on the rear
panel.
Pin Assignments
Pin #| Assignment| Pin #| Assignment| Pin #|
Assignment
---|---|---|---|---|---
1| DMX In Data +| 4| DALI 1| 7| OV
2| DMX In Data –| 5| DALI 2| 8| OV
3| DMX Out Data +| 6| DMX Out Data –| |
IP65 units are supplied with a factory-installed 2m length of hybrid mains/DMX cable that features a waterproof gland. The DMX wire assignments for IP65 units are:
Wire Color | Assignment | Wire Color | Assignment |
---|---|---|---|
Red | DALI1 | Black | NC |
Black | DALI2 | ||
White | NC |
DIFFUSION FILTERS
An optional Image Spot OPTI-FLECS™ Filter Pack is available and features three pre-cut, 43mm round diffusion filters that soften Image Spot’s beam for spotlighting purposes. The OPTI-FLECS Filter Pack includes:
- Retaining Ring
- Soft Diffusion – 43mm dia.
- Smoothing Frost – 43mm dia.
- Double Powder Frost – 43mm dia.
To install OPTI-FLECS filters into the Image Spot: insert the 43mm disc into the front end of the lens tube and then secure the filter into place using the Retaining Ring.
DICHROIC COLOR FILTERS
Rosco Permacolor dichroic filters are available to provide fully customizable,
long-term color options for your Image Spot. For optimal performance and
installation, specify Image Spot Permacolor Filters that feature custom
bezels to fit securely inside the Image Spot gobo cassette.
Install the Image Spot Permacolor Filter into the gobo cassette. The gobo
cassette is deep enough to accept both an Image Spot Gobo and an Image Spot
Permacolor Filter. It is recommended that the Permacolor Filter be installed
on the “lamp-side” of the two. When properly installed, the order should be
lamp -> Image Spot Permacolor Filter -> Image Spot Gobo -> Lens Tube.
ACCESSORIES
Item Number | Description |
---|---|
2.96E+11 | Image Spot Very Narrow-Angle Lens Optic / 10º |
2.96E+11 | Image Spot Narrow Angle Lens Optic / 19º |
2.96E+11 | Image Spot Medium Angle Lens Optic / 25º |
2.96E+11 | Image Spot Wide Angle Lens Optic / 30º |
2.96E+11 | Image Spot OPTI-FLECS Filter Pack with Retaining Ring |
2.96E+11 | Image Spot Safety Cable, 3-ft (1m) |
2.96E+11 | Rosco Pole Mount Accessory – Black |
2.96E+11 | Rosco Pole Mount Accessory – White |
2.96E+11 | Rosco Wall Mount Accessory – Black |
2.96E+11 | Rosco Wall Mount Accessory – White |
2.96E+11 | Image Spot Snoot |
2.96E+11 | Image Spot 1/2 Snoot |
ORDERING GOBOS & PERMACOLOR FILTERS
Gobos and Permacolor Dichroic Filters for the Image Spot projector can be easily ordered through any Rosco dealer. Visit www.rosco.com to locate the dealer nearest you and provide them with the information below.
Standard Gobos
XXXXX-SPOT| Image Spot Standard Gobo, XXXXX = the five-digit standard gobo
number
---|---
Custom Gobos
2507210ISPOT| Image Spot Custom Steel Gobo
260CUSBWOSPO| Image Spot Custom B&W Glass Gobo
260CUS1COSPO| Image Spot Custom One-Color Glass Gobo
260CUS2COSPO| Image Spot Custom Two-Color Glass Gobo
260CUSMCOSPO| Image Spot Custom Multi-Color Glass Gobo
Permacolor Dichroic Filters
1203-XXXX-SPOT
Image Spot Permacolor Dichroic Glass Filter for Gobo Slot, XXXX – four-
digit color number
For assistance ordering or specifying gobos or Permacolor filters for the
Image Spot, please contact our Gobo
Customer Service Centers:
Americas
Toll-Free in the US: 866-228-2256
customgobo@rosco.com
Outside of the US: 512-388-5299
EMAIL
+44 (0)20 8659 2300
salesadmin@rosco.com
TECHNICAL SPECIFICATIONS
Power
Input Voltage: Universal 100-277VAC+/-10%
Maximum Power
Consumption: 45W
Data Control: DMX 512/DALI – RJ45 (IP40)
0-10V dimming connection/Cat5e Cable (IP65)
Hybrid data/mains cable (IP65)
Physical Characteristics
Dimensions: 7.8 in. x 4.8 in. x 6.8 in.
(including yoke) (198 mm x 123 mm x 172 mm)
HT Variant: 9.3 in x 4.8 in. x 6.8 in.
(236 mm x 123 mm x 172 mm)
Weight: 5.5 lbs. (2.5 kg)
HT Variant: 5.9 lbs (2.7kg)
LED
LED Options: 3000K/96 CRI/600lm
5500K/80 CRI/800lm
LM-79-08: 70,000 hours @ 25°C
UV/385nm peak wavelength
Image Spot UV: 20,000 hours @ 25°C
Gobo Specifications
Rosco Image Spot Gobo with custom carrier
Working Environment
Ambient Temp.: Working temperature: -13° to 104°F (-25° to +40°C)
HT Variant: -13° to 122°F (-25° to +50°C)
Humidity: 20 ~ 90% RH non-condensing
Approvals:
Conforms to UL STD # 62368-1 & # 60950-22
Certified to CSA STDS C22.2 # 62368-1 & # 60950-22
Ratings:
IP40 Indoor Use Only
IP65 Outdoor Use in Wet Environments
Environmental:
Disposal of Old Electrical & Electronic Equipment
This symbol on the product or on its packaging indicates that this product
shall not be treated as household waste.
3-YEAR LIMITED WARRANTY
Rosco Laboratories warrants to the first retail purchaser that this Product
will be free from defects in workmanship and material for a period of three
years from the date of original purchase.
For warranty service, you must be able to provide proof of purchase. Should
this Product prove defective during the warranty period, please contact your
local Rosco office for Return Authorization. No warranty service will be
performed without Return Authorization.
At Rosco’s sole discretion, covered Products will be repaired or replaced with
new or refurbished equipment or a model of like kind and quality. Exchanged or
replaced parts and Products assume the remaining warranty period of the
original product covered by this limited warranty. You are responsible for
securely packaging the defective Product and returning it to Rosco as per the
instructions of the Return Authorization. Within North America, Rosco will
ship the repaired or replaced Product to you freight prepaid. Shipments to
other locations will be made freight collect.
This warranty is non-transferable and does not extend beyond the first retail
purchase of the Product.
This warranty does not cover damage to the Rosco Product caused by parts not
manufactured, distributed, or certified by Rosco.
Rosco is not obligated to provide warranty service should the Product fail to
be properly maintained or fail to function properly as a result of misuse,
abuse, improper installation, neglect, improper shipping, damage caused by
disasters such as flood, fire, and lightning, improper electrical current or
unauthorized service repairs other than those by a Rosco Authorized Servicer.
If a claimed defect cannot be identified or reproduced, you will be held
responsible for the costs incurred.
Unless otherwise stipulated by state law, all warranties expressed or implied
are limited to the three (3) year period of this warranty.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
EXPRESS OR IMPLIED WARRANT IES INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR
PURPOSE. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY AND UNLESS EXCLUSIONS ARE
SPECIFICALLY FORBIDDEN BY STATE LAW, NEITHER ROSCO NOR ITS AFFILIATES WILL BE
LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURY TO PERSONS OR PROPERTY,
RESULTING FROM THE USE OR INABILITY TO USE THE ROSCO PRODUCT, WHETHER
RESULTING FROM BREACH OF WARRANTY OR ANY OTHER LEGAL THEORY.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>