ROSCO DMG MINI Ultra Bright Soft Light Instruction Manual
- June 1, 2024
- ROSCO
Table of Contents
ROSCO DMG MINI Ultra Bright Soft Light
Specifications
- Product Name: CRMX2
- Compatible Models: DMG MINI, DMG SL1, DMG MAXI
- Manufacturer : Rosco
Product Usage Instructions
Step 1: Extract the zip file
Step 2: Install Drivers
- If updating the MIX Controller for the first time, install drivers by running lct_installer_1.exe and unticking the ‘View readme file’ checkbox.
Step 3: Open Firmware Installation Program
- Launch DFUSec.exe to open the firmware installation program on your PC. Untick the ‘Lock LINK2 function’ checkbox under the File menu.
Step 4: Connect and Prepare
- Connect the MIX Controller or DMG MAXI to power.
- Connect the MIX Controller or DMG MAXI to the PC using a USB to Micro USB cable.
- Press and hold down the Red Dimmer button and Power button simultaneously.
- Release the Red Dimmer button but continue to press the Power button.
Step 5: Begin the Upgrade Process
- While holding down the Power button, click Start on your PC to initiate the upgrade process. Continue holding the Power button until completion.
Step 6: Check the Log Message
- Monitor log messages to verify completion of the upgrade steps.
Step 7: Monitor Progress
- Release the Power button and observe the upgrade progress on the controller display.
Step 8: Complete Upgrade
- Wait for approximately 2 minutes for the upgrade process to finish.
Step 9: Turn OFF and Close Program
- Turn off the MIX Controller or DMG MAXI and close the firmware installation program on your PC.
Step 10: Download and Reinstall Firmware
- Download the latest MIX 2.1 Firmware and repeat steps 1-6 using the files from the firmware .zip file.
Step 11: Verify Firmware Installation
- Check for the pre-configured Firmware V2.x.x file names in the firmware installation program to confirm proper reinstallation.
FAQ
Q: What should I do if I encounter issues during the upgrade process?
A: If you face any problems during the upgrade, please contact TechSupport@rosco.com for assistance.
-
This instruction sheet is for updating the LumenRadio CRMX chip inside the DMG MINI, DMG SL1, and DMG MAXI fixtures to CRMX2. DMG DASH w/ CRMX fixtures can be updated to CRMX2 by updating the fixture’s firmware via the myMIX™ app.
-
To upgrade the LumenRadio CRMX chip to CRMX2, temporary firmware needs to be installed in the DMG MAXI and the MIX Controller for the DMG MINI & SL1.
-
IMPORTANT: This temporary firmware is only used to upgrade the CRMX chip to CRMX². Once the firmware has been installed and the CRMX2 update is complete, the MIX 2.1 Firmware must be reinstalled to make the controller/fixture functional again.
Once the temporary firmware and drivers have been downloaded, the CRMX2 upgrade process takes about two minutes. A progress indicator is displayed during the update process. -
To begin, download the CRMX2 Firmware Update.zip file to a PC (Windows 10 or higher) and follow the steps below.
INSTALLATION STEP
- STEP 1 Extract the zip file
- STEP 2 If you have never updated the MIX Controller with this computer before, you will need to install the drivers.
- Launch lct_installer_1.exe to install the drivers.
- Untick the View readme file checkbox.
STEP 3
-
1. Launch DFUSec.exe to open the firmware installation program on your PC. - Go to File and untick the Lock LINK2 function checkbox.
STEP 4
- Connect the MIX Controller or the DMG MAXI to power. If the Controller or the fixture turns ON – turn it back OFF.
- Connect the MIX Controller or the DMG MAXI to the PC using a USB to Micro USB cable.
- Push the Red Dimmer button and keep it pressed down.
- Push the Power button on the MIX Controller or DMG MAXI and keep it pressed down while continuing to press the Dimmer button. You should now be holding down both the Power and the Dimmer buttons.
- Release the Red Dimmer button but continue to press the Power button.
STEP 5
- While continuing to press the Power button on the MIX Controller or DMG MAXI fixture, click Start on your PC to begin the upgrade process. Continue holding down the Power button until the process is completed.
STEP 6
- Check the log message to see when the two “PROGRAM STEPS” show as completed.
STEP 7
- Release the Power button on the MIX Controller or DMG MAXI. The controller display will show the upgrade progress.
STEP 8
- After ~2 minutes, the upgrade will be complete.
- At this point, the LumenRadio CRMX chip has been updated, but the MIX 2.1 Firmware needs to be reinstalled again for the controller/fixture to be operational.
STEP 9
- Press the Power button on the MIX Controller or DMG MAXI fixture to turn it OFF, and then close the firmware installation program on your PC.
STEP 10
- Download the most up-to-date MIX 2.1 Firmware and then repeat steps 1-6 using the files contained in the MIX Firmware .zip file.
STEP 11
- To ensure the firmware has been properly reinstalled, check for the pre-configured Firmware V2.x.x file names in the firmware installation program.
- The CRMX2 Update is complete. If you have experienced any issues during the upgrade process, please contact: TechSupport@rosco.com
- WWW.ROSCO.COM
Documents / Resources
|
ROSCO DMG MINI Ultra Bright Soft
Light
[pdf] Instruction Manual
DMG MINI Ultra Bright Soft Light, DMG MINI, Ultra Bright Soft Light, Bright
Soft Light, Soft Light, Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>