SmallRig Wave W2-L Wireless Lavalier Microphone User Manual
- June 5, 2024
- SmallRig
Table of Contents
SmallRig Wave W2-L Wireless Lavalier Microphone Intended Use
- Please read this User Manual carefully, especially the “Warnings”.
- Please use or store the product in the environment mentioned herein.
- Failure to use the product as per this User Manual or under the specified working and storage conditions will be deemed as improper use.
In the Box Product Details
Transmitter (TX)
- On / Off button
- “+-” microphone gain adjustment button
- LED indicator light
- Charging contact
- Collar clip
- Microphone pickup hole
Receiver (RX)
- On I Off button
- LED indicator ligh
- Charging contact
- Adapter interface
Charging Case
- Pair button
- LED indicator light
- USB-C charging port
- Transmitter (TX)
- 3.5mm TRS Adapter
- 3.5mm TRRS Adapter
- Receiver (RX)
Product Operations
- Pairing and Use the microphone Ix and receiver HX have Deen paired before leaving the factory. You can plug RX into the mobile phone or other devices after taking it out from the charging case. Then TX will automatically start ana cay our painting connection Use Take out microphone 1X and clamp it at the collar. Take out the receiver and plug into the corresponding interface of the device and you are ready to go. >Manual pairing: transmitter (1X) and receiver (X) pairing is through pressing the Pair button for 5 seconds in the charging case, it painng success the white lights flash 3 times after paired success, the indicator lights of the transmitter (1X)/ receiver (RX) are normal white on when take out and working. it is not paired success, the indicator lights flash white slowly. On/Oft: Long press the on / oft button for 2 seconds on/of, white light is on. Automatic re-connection ine microphone has been paired successfully and nas memory function. vwhen you use it next time, the microphone (x) and receiver (HXJ can be reconnected automatically: Transmitter (TX) and receiver (RX) are disconnected when exceed the connectable range they will automatically reconnected when re-entering the connectable range. He-connection: slow Trash of white light, Connected: white light normally on. Mute The on/ off button of the microphone (TX) is provided with mute function. You can short press ue on Ot DUton to enter mute function, lo disenable the mute Function, you can short press the on/off button again. Gain Adjustment: Adjust the gain through the TX”+-button, the white light flashing times show the gain adjustment levels, flashing once for the first level, flashing twice for the second level, flashing three times tor the third level, flashing tour times for the fourth level, trashing Tive times for the fifth level.
- Charging when you put the TX/RX in the charging case and the red light is normally on, it indicates that it is being charged. IF the red lignt is oft, it indicates that the charging is completed. There are four LED lights on the charging case for indicating the current electric quantity of the charging case. If one LED light of the charging case is normaly on, it indicates 25% electric quantity. Ir two LED Lights are normally on, t indicates 50% electric quantity. If three LED Lights are normlly on, it indicates 75% electric quantity. If four LED lights are normally on, it indicates 100% electric quantity.
Product Specification
Product Parameters
| Wireless band | 2AG |
|---|---|
| Pickup mode | Omni-directional |
| Frequency response | 20Hz ~ 20kHz |
| THD | < 0.75% |
| Signal to noise ratio | e65dB |
| Sampling rate | 48kHz |
| Bit | 16bit |
| Microphone Sensitivity | -38 ± 3dB (OdB=1V / Pa.at 1kHz) |
| Wireless distance | 1OOm at maximum (no obstacles) |
Endurance time
| 5 hours for using TX/ RX one time
20 hours for using in combination with the charging base
Port of charging case| USB-C
Battery specification
| TX: 1OOmAh 3.7V 0.37Wh
RX: l 50mAh 3.7V 0.555Wh
Charging base l 300mAh 3.7V 4.81Wh
Charging time
| TX:lh
RX: 1.5h
Charging Case: 2.5h
Frequency Response Directionality FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment is
the device complies with Part ib of the F Hues. operation is Subject to the
following wo conditions (0) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired This device and its antenna(9) must not
be co-located or operating in conjunction with any other antenna or
transmitter
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to art 15 of the FCC Rules. stalled a not is sed in
accordance with the instructions, may cause harmful interference to radio
communications, HOwever, there is ro guarantee tnat interferenCe will not
o0Cur in a particular installation. this equipment does cause harmful
interference to radio or television reception, which can De determined by
turning the equipment or and on, the user iS encouraged to try to correct the
interference Dy one or more of the following measures ewes ent and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected,
- Consult the dealer or an experienced radio iv technician for help.
- The device has been evaluated to meet general
RF exposure requirements
The device can be used in or tab le exposure condition without restriction.
FCC ID: 2AZW-3493LEQ