TESLA TSL-SWI-ZIGBEE1 Smart Switch ZigBee User Guide
- June 5, 2024
- Tesla
Table of Contents
TESLA TSL-SWI-ZIGBEE1 Smart Switch ZigBee
- Voice/APP Control
- Smart Home Automation with Multi devices
- Silent switch with LED Indication
Product Indtoruction
Smart switch products are suitable for electrical equipment such as lightning,
fans, curtains, etc., through the network, voice and APP remote control
functions, with various sensors to easily achieve home automation.
Specification
Input Power: | 200~240V AC 50/60Hz |
---|---|
Resistive load: | INC 3-300W, LED 5-300W |
Communication: | ZigBee 3.0 |
Standby Power: | ≤0.5W |
Working Temperature: | -10°C ~ 45°C |
Working Humidity: | <90% |
Life Cycle: | 50k times |
Dimension: | 86x86x37.5mm |
Product outline
Indicator Light Status
Light Color Green | Light Status | Switch Status: |
---|---|---|
Green | OFF | The switch turn off |
ON | The switch turn on | |
Flicker | The switch is in the quick configure mode |
Contents Supplied
Tools You‘ll Need
Approximately 30 minutes of your time to install and setup the Switch
Installation
WARNING: RISK OF ELECTRIC SHOCK
This product installation requires handling 100-240 volt wiring.
Follow each step carefully. If any concerns handling wiring, hire a qualified
electrician. Ensure all work meets applicable local and national codes.
-
Turn Off The Breaker
Turn off the circuit break and use the electrical tester to test the power. -
Connection Diagram
-
GANG
-
GANG
-
Remove The Panel
Remove the switch panel cover of the switch. -
Mount The Switch
Use the screws provided. -
Attach The Wallplate
Attach the adapter to the switch using the screws provided and snap on the wallplate. -
Turn On The power
Turn the power back on at the circuit breaker
APP Operation
-
Preparation for use
- Tesla Smart is available for both iOS and Android OS. Search the name ‚Tesla Smart‘ in App Store or Android Market, or scan the QR-Code to download the App and register or login your account.
- Make sure that the smartphone is connected to the 2.4Ghz network.
-
ADD Devices (ZigBee)
-
Press and hold any button of the switch get into Quick Configure Mode.
-
Open the App, press and hold any button to get into network pairing mode.
Open the App, on the “Tesla Smart ZigBee Hub” page, click “add subdevice”, and click “LED already blink”. -
search nearby device and discover the Tesla Smart Switch Zigbee.
-
After adding the device successfully, click “DONE”
-
After adding successfully, the product will be displayed on the intelligent gateway Interface
-
Click “Tesla Smart Switch Zigbee” to enter controlling mode.
-
Click to enter the switch control interface. Long press the switch button in the control interface to modify the switch name.
-
Press and hold the sketch map of the switch you can modify the name of this gang of the switch, like “bedroom”, “living room”
-
Controlling the on/off, setting timer, countdown on the App.
-
-
Control Switch
- Control switch with APP
Troubleshooting
- Switch has not power on? The smart switch products need to be powered by the neutral line. If there is no neutral line in the inch-Manor location, the smart switch can not work
- Can not connect to APP? Make sure the mobile phone and devices (gateways) in a same Wi-Fl network, and the device power an get into pair mode, make sure the device has good signal to support communication.
- How far can be controlled? Please make sure that the distance between the product and the Wi-Fi router or gateway does no- exceed 25 meters, If the partition wall is used but the material and thickness of the wall will have a greater impact communication, based on the actual situation, users can consider adjusting the location of the Wi-Fi router or gateway or increasing Wi-Fi routers or gateways to ensure normal product communication.
- Can the Switch still work if the network is disconnected? In the event of a network disconnection, the status indicator will flash. At this time, all APP control, smart linkage and other network functions will be invalid but the local control will not be affected.
Reset
Press and hold switch button for 5s until LED flash to reset the switch and
get into quick configure mode.
Remark:
- Smart phone and device must connect to same Wi-Fi during setup mode
- The device must be added to theaccount before it can be controlled remotely
- After the device is successfully acce ssed, other users can obtain control of the product through the sharing function.
INFORMATION ABOUT DISPOSAL AND RECYCLING
This product is marked with the symbol for separate collection. The product
must be disposed of in accordance with the regulations for disposal of
electrical and electronic equipment (Directive 2012/19/EU on waste electrical
and electronic equipment). Disposal together with regular municipal waste is
prohibited. Dispose of all electrical and electronic products in accordance
with all local and European regulations at the designated collection points
which hold the appropriate authorisation and certification in line with the
local and legislative regulations. Correct disposal and recycling help to
minimise impacts on the environment and human health. Further information
regarding disposal can be obtained from the vendor, authorised service centre
or local authorities.
EU DECLARATION OF CONFORMITY
Hereby, Tesla Global Limited declares that the radio equipment type ESW-1ZBC-
EU, ESW-2ZBC-EU is in compliance with EU directives. The full text of the EU
declaration of conformity is available at the following internet address:
tsl.sh/doc
Connectivity: ZigBee IEEE 802.15.4
Frequency band: 2.400 – 2.480 GHz
Max. radio-frequency power (EIRP): < 20 dBm
Manufacturer
Tesla Global Limited
Far East Consortium Building, 121 Des Voeux Road Central Hong Kong
www.teslasmart.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>