BRANDMOTION TRNS-3110 Transparent Trailer HD Monitor Rear Vision System Instruction Manual

BRAND MOTION TRNS-3110 Transparent Trailer HD Monitor Rear Vision System

Kit Contents

Recommended Tools| Components for installing the TRNS- 3110
---|---

1x 7” Monitor w/ harness

1x Cameras w/ harness
1x Mounting Foot
1x Exterior Video Connectors
1x Video Exterior Cable
3x 4-Pin Video Extension Cable
1x Mounting Hardware

Installation of the 7” Display

1.       Find the desired location for the display to be mounted in the vehicle.

2.       Once a location has been selected, install the mount on the monitor by loosening the

retaining nut and sliding the metal wedge into the groove on the back of the display.

3.       Hand tighten the bracket to the monitor. The mounting bracket should be firmly in place and unable to wiggle.

4.       Clean the desired location with alcohol or adhesive promoter

5.       Remove the protective film from the adhesive on the bottom of the mounting bracket

6.       Set the display in place and apply firm pres- sure to the top surface of the mounting plate to ensure good adhesion to the mounting surface

|

1.       Connect YELLOW wire to a 12V+ accessory or ignition controlled power source

2.       Connect the eyelet on the BLACK wire to a chassis ground. You can use a factory ground bolt if available

3.       All three of the 4-pin connectors are labeled with the respective channels for video connec- tions later in the installation

4.       Trigger wires are 12V+ activated and are labeled for the respective channels that they control. Be aware that when a channel is triggered by wire, all functions of the monitor (power buttons, menu buttons, channel but- tons) will not be functional while a channel is triggered by wire.

|
Part 2| Display Power, Video, and Trigger Wiring
---|---

1.       Connect YELLOW wire to a 12V+ accessory or ignition controlled power source

2.       Connect the eyelet on the BLACK wire to a chassis ground. You can use a factory ground bolt if available

3.       All three of the 4-pin connectors are labeled with the respective channels for video connec- tions later in the installation

4.       Trigger wires are 12V+ activated and are labeled for the respective channels that they control. Be aware that when a channel is triggered by wire, all functions of the monitor (power buttons, menu buttons, channel but- tons) will not be functional while a channel is triggered by wire.

|
Part 3| Function test of the Transparent Trailer Monitor
---|---

1.       Connect camera directly to desired channel on the monitor harness

2.       Test mirror and camera by turning on ignition power. You can also plug a camera directly into the mirror if you want to test both channels with video before proceeding.

|

Installation of the Rear Trailer Camera

1.       Remove the 4 Allen screws that are located on the sides of the camera. Then remove the camera mounting bracket and visor.

2.       Find an appropriate place to mount the back- up camera. Line up the foot bracket to ensure that there is enough space to attach the cam- era to the body.

3.       Attach the mounting foot using either self-tap- ping screws or a bolt and nut.

4.       Use a 1” hole saw to drill a hole for the camera harness.

5.       Feed the harness through the drilled hole, fit the grommet to the inside of the hole. De- pending on the installation, the grommet may not be water tight. Use of silicone or other sealing agents is always recommended.

6.       Reattach camera and visor to the mounting bracket. Make sure the camera is oriented UP by seeing the light sensor on the left side of the camera when looking at it.

|

NOTE: If you do not wish to drill holes in the visible space of the factory bumper or trailer, you can attach the included L brackets in your desired location at the back of the vehicle or front of trailer and mount the plugs directly to the L bracketbumper or trailer, you can attach the included brackets in your desired location at the back of the vehicle or front of trailer and mount the plugs directly to the L bracket

1.       Using the included template, drill a 1” hole fac- ing the rear of the vehicle’s bumper to mount the vehicle plug. Look behind the bumper or bumper cover to make sure there is nothing on the backside of where the plug is going to go.

2.       Using the same template, drill two 3/16” holes for the mounting screws. If you are using the online instructions and do not have a tem- plate, you can insert the plug to mark your hole locations, remove the plug, and drill your 3/16” holes

3.       Unwind your two 10m harnesses that are attached to the plug and feed through the 1” hole.

4.       Attach the plug to the vehicle by removing the 2 nuts and washers. Then attach the plug to the vehicle and secure it with the original washers and nuts.

5.       Run the harness from the rear of the truck to the area where the mirror is located. If you have a second camera mounted on the trailer, you will need to run both harnesses. If not, we still recommend running the cables together in case an additional camera is installed at a later time.

6.       Connect the 4-pin connector to the mirror harness 4-pin connector.

|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>