JascoPro Series Plug-In Smart Switch User Manual
- June 12, 2024
- JASCO
Table of Contents
Plug-in Smart Switch ZWN4109/79244
Z-Wave® certified
wireless lighting control
Thank you for your purchase!
| Instructions made easy| | Register your product
---|---|---|---
https://byjasco.com/79244i| Read instructions
or watch easy-to- follow video.| https://byjasco.com/register-your-product|
Receive exclusive deals and register your product
For additional JascoPro Series products, visit our website www.jascopro.com.
Like our product?
Leave a review on your favorite rentier website or
amazon.com
Having problems?
Let us know how we can help.
Call 1800-654-8483 between 7AM-8PM, M-F, Central Time.
ADDING YOUR DEVICE TO A Z-WAVE NETWORK
- Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
- Once the controller is ready to add your device, press the program button of the smart switch.
You have complete control to turn your lamp ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller.
1f your Z-Wave certified controller features remote access, you can control your lamp from your mobile devices.
If prompted by the controller to enter the S2 security code, refer to the GR code/security number on the side of the box o the GR code label on the product (see Figure 1). Enter the 5-diigit code.
Figure 1:
TO REMOVE AND RESET THE DEVICE
- Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network
- Once the controller is ready to remove your device, press the program button of the smart switch.
TO RETURN YOUR SWITCH TO FACTORY DEFAULTS
- If plugged in, unplug the switch from the receptacle.
- Press and hold the program button for at least three seconds while you plug the switch into a receptacle.
NOTE: This should only be used if your network’s primary controller is missing or otherwise inoperable.
NOTE: SmartStart enabled products can be added into & Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.
SPECIFICATIONS — IMPORTANT!
ZWN4109/79244 Power:125VAC, 60Hz
Signal (frequency): 908.4019k, 908. 4216k, 916. 001411z, 912.006111z, 920.
cook
Maximum load: 1250W (10A) tungsten, 1/2HP motor or 1875W (15A) resistive
Wireless Range (Classic): Up to 150ft. line of sight between the wireless
controller and the closest Z-Wave receiver module
Wireless Range (Long Range): Up to 1300ft. line of sight to the wireless
controller
Operating temperature range 32-104° F (0-40° C)
For indoor use only
Specifications subject to change without notice due to continuing product
improvement
NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EGUIPMENT
2-WAVE ENABLED DEVICES SHOULD NEVER BE USED T0 SUPPLY POWER T0 OR CONTROL THE
ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPHET
FEATURES
Must not exceed 1250W tungsten, 1875W (15A) resistive or 1/2HP motor
- One Z-Wave controlled AC outlet for standard incandescent lighting, CFL/LEDs, fans or small appliances
- Remote ON/OFF operation via the Z-Wave controller
- Manual ON/OFF control with the side-mounted push button
- Space-efficient design Grounded three-wire power connection for safety
- This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config
- Supports Z-Wave long range — requires Z-Wave hub that supports Z-Wave long range
- Can be added as a Z-Wave long range or standard Z-Wave device
A. Manual/program button
Single press — turn ON/OFF the device
Single press — include or exclude in Z-Wave network
B. LED indicator
C. Z-Wave controlled outlet — can remotely turn.
ON/OFF the connected device 
CYCLELED
The LED behind the program button acts as a guide light or
status indicator.
How to cycle through options:
Press program button 10 times quickly.
- LED is ON when the load is ON (indicates the outlet is ON) (default)
- LED is always OFF
- LED is always ON
- LED is ON when the load is OFF (guide light in the dark)
PLUGGING IN R Z-WAVE DEVICE
Plug in the smart switch to an indoor grounded outlet. 
NOTE: Plug directly into outlet. Do not use with extension cords.
Plug the device to be control into the Z-Wave controlled outlet. Be sure the
power switch on the controlled device is in the ON position. 
The manual/program button on the smart switch allows the user to:
- Manually turn ON/OFF the connected device.
- Add/remove the smart switch from the network.
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other
Z-Wave certified devices from other manufacturers and/or other applications.
All non-battery operated nodes within the network will act as repeaters
regardless of vendor to increase reliability of the network.
This device supports association command class (3 Groups)
- Association Group i supports Lifeline Binary Switch Report
- Association Group 2 supports L: Set and is controlled by pressing the ON or OFF button with the local load
- Association Group 3 supports Basic Set and is controlled by double pressing the ON or OFF button
- Each Association Group supports S total nodes
For product patent information, visit ww.byjasco.com/patents.
All brand names shown are trademarks of their respective owners.
MADE IN VIETNAM
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City,
OK 73114. This Jasco product has a 5-year limited warranty. Visit
www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at
1-800-654-8483, M-F, 7AM-8PM Central
Time. ©JASCO 2023 I ZWN4109 /79244 I 05/09/23 vl
WARRANTY/GARANTIE
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1), M-F, 7AM-8PM Central Time or www.byjasco.com if the unit should prove defective within the warranty period.
FCC/IC
Suppliers Declaration of Conformity I Model #2rmlosn9244Jasco Products Co.,10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the fcc/rss rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
- Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-5(B)/NMB-5(B)