SEALEY FGE01 EXTENDING STEEL GARAGE EXTENSION Instruction Manual

2.5 X 4.5 X 2.5M EXTENDING STEEL GARAGE
EXTENSION
MODEL NO: FGE01

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT IS CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

| | |
---|---|---|---
Refer to instructions| Wear protective gloves| Wear safety footwear| Wear eye protection

SAFETY

√ Read all safety instructions to reduce the risk of injury or death.
√ This is a temporary structure and is not recommended as a permanent structure.
√ Choose your shelter’s location carefully. Check for overhead utility lines, branches, etc. DO NOT install near roofs or other structures that may shed snow, ice or excessive run-off onto your shelter. Keep away from electrical wires!
√ Install your shelter on a level surface.
√ Check municipal by-laws prior to setting up the product.
√ Have an overview of all parts before attempting installation. Make sure all components are available.
x DO NOT use this product in environments for which it is not intended (i.e. extreme cold, high winds, extreme heat, heavy rainfall, etc).
√ Always wear safety glasses when assembling this product. Wear gloves when working with tubing to prevent cuts or abrasions.
√ Anchors must be used in all shelters. Covers should NOT be installed on any product until it has been properly anchored to the ground.
√ Proper anchoring and keeping cover tight and free of snow and debris, is the responsibility of the consumer.
√ Damages caused by improper anchoring are not covered under warranty.
√ Keep all flame and heat sources away from the shelter fabric. The fabric will burn if left in continuous contact with a flame source.
x DO NOT use open flames or cooking or heating devices inside or in close proximity to the product, including all types of stoves, gas heaters, gas lanterns, citronella torches, mosquito coils, etc.
x DO NOT cook, smoke, refuel or use any open flame devices in or around the shelter.
x DO NOT store flammable liquids (gasoline, kerosene, propane, etc.) in the shelter.
x DO NOT operate gas-powered vehicles/equipment in or around the shelter.
√ Keep open flames a safe distance away from the shelter.
x DO NOT use hard-edged tools or instruments, such as rakes or shovels, to remove snow. These can cause punctures to the cover.
x DO NOT start the engine of any vehicle or machine inside a closed shelter. Ensure that there is adequate ventilation for starting engines and for any work with paints, cleaners, etc.
√ This shelter is NOT designed to support heavy snow or ice loads. Snow or ice accumulation may cause your shelter to collapse. To avoid overload, brush snow and ice off the rooftop with a broom or mop.
√ To prevent collapse, damage to property, personal injury, and/or death, NEVER clear the roof of snow or debris from inside the shelter.
√ Keep children away during assembly. This product contains small parts which can be swallowed by children.
x DO NOT attempt to assemble the product if any parts are missing.
√ At least 4 people are needed to complete the assembly as some of the steps require heavy lifting.
‰ WARNING! DO NOT leave the shed unattended during assembly. Otherwise, personal injury or damage to the shed may occur.

INTRODUCTION

Extending the garage extension is perfect for allowing the temporary use of a driveway as a garage. Supplied with a powder-coated steel frame. 195g/ m2 PE Tarp with UV protection and completely waterproof.

SPECIFICATION

Model No:………………………………………………………….FGE01
Door Size: ……………………………. 2500mm (W) x 2000mm (H)
Material: ………………………………..195g/m2 PE Tarp and Steel
Overall Size (W x D x H): …………………………2.5 x 4.5 x 2.5m

CONTENTS

ASSEMBLY

5.1. Place all parts from the packaging box in a cleared area and arrange them on the ground.
5.2. Remove all packaging materials and place them back in the box.
x DO NOT dispose of the packaging materials until assembly is complete.
5.3. Check for completeness and transport damages.
‰ WARNING! DO NOT place the product under trees from which hard fruit such as apples, walnuts or heavy pine cones, etc., may fall. The shed’s cover only protects against normal leaves and light debris, whereas large branches or other falling items may puncture or tear the cover material. 5.4. STEP 1 (FIG 2)
5.4.1. Take the riser sections out of the box as shown below.
5.4.2. Screw all the casters (fig.2.18) to the bottoms of the legs as per the below diagram.

5.5. STEP 2 (FIG 3)
5.5.1. Insert tube (fig.3.4) into the tube (fig.3.3) and secure it with Bolt M6x55 (fig.3.13) and M6 Nut (fig.3.15), then slide Part (fig.3.5) onto tube (fig.3.3).
5.5.2. Connect 1pc of Peak Centre Tube (fig.3.1) and 2pcs of Roof Tube (fig.3.2) as per the below diagram.
5.5.3. Then use Connecting Plate (fig.3.6) to connect the end of the tube (fig.3.3) and one side of the tube (fig.3.2) together using Bolt M6x55 (fig.3.13) and M6 Nut (fig.3.15).
5.5.4. In the same way connect the end of the tube (fig.3.4) and the other side of the tube (fig.3.2) together using Bolt M6x55 (fig.3.13) and M6 Nut (fig.3.15).
5.5.5. Repeat the above 3 steps to finish the other 4 sections.

5.6. STEP 3 (FIG.4 & .5)
5.6.1. Follow the below diagrams (fig.4 & .5), and assemble the 5 groups of roof structures onto the two sets of Riser Components (fig.4.10 & 11). 5.7. STEP 4 (FIG.6 & 7)
5.7.1. Now assemble the pipe Jacking Component (fig.6.12) on top of parts 3 & 4 Brace by M8x70 (fig.6.14) and M8 Nut (fig.6.16).
5.7.2. Please refer to the attached diagram of fig. 7, A, B, C, and D. Make sure Axle Tube (fig.6.9) is in the right place, either below part 12 or above part 12 to make sure the components are spaced evenly.

5.8. STEP 5 (FIG.8)
5.8.1. Move the wheels close to the center to take the tension out of the whole structure, then put the cover (fig.8.19) onto the whole frame, and then pull the whole structure tight. 5.8.2. Walk around the whole structure, pull the cover tight, and then hook the cover into the suitable hole on the tube legs.
5.8.3. Pull the cover tight onto the frame. Use the ‘hook and loop tape’ straps sewn on the cover to secure it (fig.9).

5.9. STEP 6 (FIG.10)
5.9.1. Carefully move the assembled product to the wall where you want it to stay, then use Anchorage Clip (fig.9.8) and Expansion Bolt (fig.10.17) to fix it to the wall.
5.9.2. Then you can latch it to the ground using the stakes (fig.10.7).

MAINTENANCE

x DO NOT use bleach, alkaline or harsh detergents for cleaning. Doing so will damage the polyethylene material. Soap and warm water are recommended.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk 
© Jack Sealey Limited
Original Language Version
FGE01 Issue 2 (H,2) 07/01/22

Documents / Resources

| SEALEY FGE01 EXTENDING STEEL GARAGE EXTENSION [pdf] Instruction Manual
FGE01, 2.5 X 4.5 X 2.5M, EXTENDING STEEL GARAGE EXTENSION, GARAGE EXTENSION
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>