VONROC WL502DC RECHARGEABLE WORK LIGHT 10W Instructions
- June 5, 2024
- VONROC
Table of Contents
RECHARGEABLE WORK LIGHT 10W
WL502DC
SAFETY INSTRUCTIONS
Read the enclosed safety warnings, the additional safety warnings, and the
instructions. Failure to follow the safety warnings and instructions may
result in electric shock, fire, and/or serious injury. Save the safety
warnings and the instructions for future reference.
The following symbols are used in the user manual or on the product:
Read the user manual.
Denotes risk of personal injury, loss of life, or damage to the tool in case
of non-observance of the instructions in this manual.
IP65 Protection class IP65.
Do not cover the lens while operating the work light. This may cause the work
light to overheat.
Do not dispose of the product in unsuitable containers.
The product is in accordance with the applicable safety standards in the
European directives.
SAFETY WARNINGS FOR WORK LIGHT
a) Please read and observe all safety warnings and instructions enclosed
with the battery or the power tool with which the battery was provided.
b) Do not work with the rechargeable work light in hazardous areas.
c) After the automatic shut-off of the rechargeable work light, do not
continue to press the On/Off button. The work light should be recharged
first.
d) Do not direct the light beam at persons or animals and do not stare into
the light beam yourself (not even from a distance).
e) Do not cover off the lens while operating the rechargeable work light.
The work light heats up during operation and can cause burns when the heat is
allowed to accumulate.
f) Do not use the rechargeable work light in road traffic. The rechargeable
work light is not approved for illumination in road traffic.
g) Do not allow children to use the rechargeable work light. It is
intended for professional use. Children can unintentionally blind themselves
or other persons.
MACHINE INFORMATION
Intended use
The rechargeable work light is intended for mobile illumination in limited
space and for a limited time in dry indoor areas and is not suitable for
general room lighting. The work light is equipped with a USB power output
which may be used to power or charge USB-compatible mobile devices.
TECHNICAL SPECIFICATIONS
| Model No. | WL502DC |
|---|---|
| Input | 5V USB Micro-B |
| Output | 5V USB |
| Battery voltage | 3.7V |
| Battery capacity | 4.4Ah |
| Power (max.) | 10W |
| Luminous fl ux | 1000lm |
| Beam angle | 60°×120° |
| Run time (at 50% brightness) Charging time | 4 hours |
| Charging time | 8 hours |
| Weight | 0.46kg |
DESCRIPTION
The numbers in the text refer to the diagrams on page 2.
- LED light
- Power button
- USB output
- USB input
- Charge level indicator
- Foldable stand
- Tripod mount
- USB charging cable
- USB Micro-B connector
- USB A connector
OPERATION
The rechargeable work light must be charged before first use.
Charging
Use the supplied USB cable (8) to charge the rechargeable work light.
- Insert the USB Micro-B connector (9) into the USB input (4)
- Insert the USB A connector (10) into a suitable USB power outlet, such as a USB wall adapter, or computer USB port.
- Observe the charge level indicator (5) to monitor the charging process. The charge indicator will blink to indicate charging is in progress
Power button
When the light is on, press the power button (2) to cycle between the
following available operating modes.
- Full brightness
- 50% brightness
- SOS fl ashing pattern
- Strobe fl ashing pattern
- Light off
When the light is off, press the power button (2) once to activate the charge
level indicator (5). The charge level indicator will display the current state
of the battery for a few seconds. Press the power button again to activate the
light and cycle between the operating modes as mentioned above.
USB power bank function
The rechargeable work light may be used a power bank to power or charge other
USB-compatible devices from the USB output (3). The power button (2) and the
chosen operating mode of the work light have no effect on the USB output. The
USB output is always active, provided the internal battery of the work light
has a suffi cent charge.
To use the power output, fi nd a suitable USB cable and plug the USB A
connector into the USB output (3) of the rechargeable work light. Plug the
other end of the USB cable into the target device. The charge level indicator
(5) will automatically light up to signal that the power output has been
activated.
MAINTENANCE
Always switch off the work light before cleaning and maintenance.
Clean the rechargeable work light regularly with a soft cloth. Remove
persistent dirt using a moist cloth with a mild detergent. Never use any
solvents or aggressive cleaning products such as gasoline, alcohol, ammonia,
etc. Such chemicals will cause irreparable damage to the synthetic components
of the work light.
ENVIRONMENT
Faulty and/or discarded electrical or electronic apparatus have to be
collected at the appropriate recycling locations. Only for EC countries
Do not dispose of power tools into domestic waste. According to the European
Guideline 2012/19/EC for Waste Electrical and Electronic Equipment and its
implementation into national rights, power tools that are no longer usable
must be collected separately and disposed of in an environmentally friendly
way.
WARRANTY
VONROC products are developed to the highest quality standards and are
guaranteed free of defects in both materials and workmanship for the period
lawfully stipulated starting from the date of original purchase. Should the
product develop any failure during this period due to defective material
and/or workmanship then contact VONROC directly.
The following circumstances are excluded from this guarantee:
- Repairs and or alterations have been made or attempted to the machine by unauthorized service centers;
- Normal wear and tear;
- The tool has been abused, misused or improperly maintained;
- Non-original spare parts have been used.
This constitutes the sole warranty made by the company either expressed or
implied.
There are no other warranties expressed or implied that extend beyond the face
hereof, herein, including the implied warranties of merchantability and
fitness for a particular purpose. In no event shall VONROC be liable for any
incidental or consequential damages. The dealer’s remedies shall be limited to
the repair or replacement of nonconforming units or parts.
The product and the user manual are subject to change. Specifi cations can
be changed without further notice.
**DECLARATION OF CONFORMITY WL502DC – RECHARGEABLE WORK LIGHT 10W**
We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European Parliament and of the Council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:
EN 60598-1, EN 60598-2-4, EN 62493, EN 55015, EN 61547
2014/30/EU, 2014/35/EU, 2011/65/EU, 2012/19/EC
Zwolle, 01-01-2022
H.G.F Rosberg
CEO
VONROC
Lingenstraat 6
8028 PM Zwolle
The Netherlands
©2022 VONROC
WWW.VONROC.COM
2201-05
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>