BRESSER BR-600BM LED Panel Light Triple Kit Instruction Manual

BRESSER BR-600BM LED Panel Light Triple Kit

GENERAL WARNINGS

DANGER OF BODILY INJURY!
Do not use in the presence of children or animals. Store out of reach of children and animals.

RISK OF MATERIAL DAMAGE!

• Make sure that no one can trip over the connection cables of the device.
• The device could be knocked over.
• Only use the recommended power cable or the recommended battery for the power supply!
• The manufacturer accepts no liability for voltage damage caused by the use of an unsuitable power supply!

DANGER OF AN ELECTRIC SHOCK!
This device contains electronic parts that are powered by a power source (power adapter). Only use the device as described in the manual. Otherwise, you run the DANGER of an ELECTRIC SHOCK. Never bend, squeeze or pull power cables, connecting cables, extensions or connectors. Protect cables from sharp edges and heat. Check this device, cables and connections for damage before use. Never attempt to operate a damaged device, or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent. Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.

RISK OF GLARE!
Make sure that people and animals do not look into the light. The high luminosity can cause glare to the eyes and afterimages. This impairment of vision can lead to accidents.

FIRE/EXPLOSION HAZARD!
Always place the device in such a way that it cannot tip over and
ensure that it is stored in a reasonably safe place.

• Keep children and animals away from the device! They could knock the device over.
• Make sure that no one can trip over connection cables. The device could be knocked over.
• Do not expose the device to high temperatures. Do not short circuit the device or dispose of in fire! Excessive heat and improper handling can cause short circuits, fires and even explosions!
• Only use the recommended power supply*!

IMPORTANT NOTE!
Do not disassemble the device! In the event of a defect, please contact your dealer. They will contact the Service Center and can arrange the return of this device for repair if necessary. Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation and before any maintenance and cleaning work. Place your device so that it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the mains supply. To disconnect the unit from the mains, always pull the mains plug and never pull the cable! Do not subject the device to excessive vibrations.

DELIVERY CONTENT

LED Light (A), remote control (B), power adapter (C), power cable (D)

PARTS OVERVIEW

1. Vents

2. 2.4G Antenna

3. LED display

4. Locking knob (tilt joint)

5. Battery holder

6. Power connection socket

7. Channel button

   • Press the “CHANNEL” button and turn the available adjustment knob to adjust the channel
   • Press the “CHANNEL” key to confirm.

8. Power button

9. Battery check button
   In situations where the only fitted battery, press the “BATTERY” key, can check the Battery electricity

10. Adjustment knob

    • Enter Full Power Mode
    • Press the “DIMMER/COLOR” button two times to enter Full Power Mode (4400k COLOR temperature)
    • Adjust brightness
    • Turn the knob to adjust the brightness 10 ~ 99%

11. U-bracket

12. Fixing screw (tripod connection)

13. Tripod connection
    REMOTE CONTROL (B)

14. LCD

15. Power button

16. – button

17. Menu button

18. + button

19. Battery compartment
    POWER ADAPTER (C) AND CABLE (D)

20. C13 socket

21. Barrel connector

22. Euro plug

23. C13 plug

ESTABLISHING THE POWER SUPPLY

1.  Insert the barrel connector (16) of the power adapter (B) into the power connection socket (6) on the LED light.
2.  Insert the C13 plug (17) of the power cable (C) into the C13 socket (14) of the power adapter (B).
3.  Insert the Euro plug (15) of the power cable (C) into the wall socket.

INSTALLING THE V-MOUNT BATTERY* (optional)

1.  Slide the fully charged battery* (2 pcs of type NP-F750/ NP-F960) into the battery holder (5) from the side so that the battery clicks into place.
2.  To remove, slide the battery* out of the holder in the opposite direction.

TURNING ON THE LED LIGHT

1.  Establish the power supply for the device (insert battery or connect power cable).
2.  Press the power button (8) for approx. 1 second to turn the device on or off.
   Important: Disconnect the device from the power supply if it is not going to be used for a long period of time!

BRIGHTNESS ADJUSTMENT

1.  Press “DIMMER/COLOR”.
2.  If the “DIMMER” corresponding indicator lights bright, you can adjust the brightness by turning the knob.

COLOR TEMPERATURE ADJUSTMENT

1.  Press “DIMMER/COLOR”.
2.  If the “COLOR” corresponding indicator lights bright, you can adjust the color temperature by turning the knob.

REMOTE CONTROL

POWERING ON/OFF THE UNIT

1.  Press the Power button (15) to switch on the unit.
2.  Long press the Power button (15) to switch off the unit.

MOVING THROUGH THE MENU

• Press the Menu button (17) to move through the menu.
• Press 1x = shows 10 “Brightness” 10 = 10%
• Press 2x = shows 56 “Colour temperature” 56 = 5600 K
• Press 3x = shows 01 “Channel” 01 = 1

SELECTING A CHANNEL

1.  Press the Menu button (17) three times to go to the channel menu.
2.  Press + or – (16/18) to choose the desired channel.
3.  Press the Menu button (17) to confirm your selection.

TURNING ON/OFF THE LIGHT

1.  By default, the light status of the selected channel is “OFF”.
2.  Press the Power button (15) to turn the light on.
3.  Long press the Power button (15) to turn off the light.

ADJUSTING THE BRIGHTNESS

1.  By default, the brightness level is 10% when the device is turned on.
2.  Press + or – (16/18) to increase or decrease the brightness.

ADJUSTING THE COLOUR TEMPERATURE

1.  Press the Menu button (17) to select the colour temperature for the current channel.
2.  Press + or – (16/18) to choose the desired colour temperature.

ADJUSTING THE TILT ANGLE

1.  Hold the light and slowly loosen the locking knob for the tilt joints (4).
2.  Move the lamp head to the desired position and tighten the locking knob (4) again hand-tight.

MOUNTING ON A TRIPOD* (optional)

1.  Loosen the fixing screw (12) for the tripod connection (13) so far that the opening of the tripod connection is exposed.
2.  Place the lamp with the opening of the tripod connection (13) on the spigot adapter of a tripod and tighten the fixing screw firmly

DISPOSAL

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal. Do not dispose of electronic devices in the household garbage! As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner. In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. The disposal in domestic waste violates the Battery Directive. Batteries that contain toxins are marked with a sign and a chemical symbol.

TECHNICAL DATA

WARRANTY & SERVICE

The regular guarantee period is 2 years and begins on the day of purchase. You can consult the full guarantee terms and details of our services at www.bresser.de/warranty_terms. Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions.

References

• Bresser | Startseite | Expand Your Horizon mit BRESSER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>