Nekteck NK-FLM02 Shiatsu Foot and Calf Massager with Heat User Manual

June 5, 2024
Nekteck

Nekteck NK-FLM02 Shiatsu Foot and Calf Massager with Heat

IMPORTANT SAFETY INSTRUCTIONS

Please read ALL instructions carefully before using the Foot & Calf Massager for the first time. We recommend that you keep this manual for future refer­ence, even if you are familiar with the product. Improper use or unautho­rized repairs are not permitted for safety reasons and will lead to loss of warranty. The basic safety precautions should always be followed. Failure to comply with this manual may cause fire, electric shock, and other serious injuries.
When using an electrical appliance, basic precautions should always be followed, including the following:
Read all instructions before using (this appliance).
DANGER – To reduce the risk of electric shock:

  • Always unplug this appliance from the electrical outlet immediately after using and before cleaning.

WARNING – Use heated surfaces carefully. May cause serious burns. Do not use over insensitive skin areas or in the presence of poor circulation. The unattended use of heat by children or incapacitated persons may be dangerous.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

  • An appliance should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.
  • Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
  • Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons.
  • Close supervision is necessary when this appliance is used by, on, or near children’ invalids’ or disabled persons.
  •  Keep the cord away from heated surfaces.
  • Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
  • DO NOT carry this appliance by supply cord or use cord as a handle.
  • Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.
  • Never drop or insert any object into any opening.
  •  DO NOT use outdoors.
  • DO NOT operate where aerosol (spray) products are being used or where oxygen is being administered
  • To disconnect, turn all controls to the off position, then remove plug from outlet.
  • DO NOT use massager in close proximity to loose clothing or jewelry.
  • Keep long hair away from massager while in use.

SAVE THESE INSTRUCTIONS

ELECTRIC SAFETY
  • The appliance is only to be used with the power adapter that comes with the appliance.
  • DO NOT use this appliance if it has been dropped or any part of the appli­ance (including the massager cloth cover, power cord, or power adapter) has been damaged.
  •  DO NOT operate the appliance with wet hands or wet feet to reduce the risk of electric shock.
  • Turn off and unplug this appliance before moving it.
  • Unplug this appliance after use and before cleaning.
  • Unplug IMMEDIATELY and DO NOT use the product if it has malfunc­tioned or has been damaged in any way. Inspect the product by a qualified person.

PACKAGE CONTENTS

  • Nekteck Shiatsu Foot & Calf Massager with Heat
  • Wireless Remote Controller
  • User Manual
  • Power Adapter
  • AAA Battery

SPECIFICATIONS

Product Name Nekteck Shiatsu Foot & Calf Massager with Heat
Color Black
Model Number NK-FLM02
Rated Voltage 12V DC=5.0A
Rated Power 60W
Dimensions 17.3 x 15 x 8.7 in/ 44 x 38 x 22.2 cm
Net Weight 11.9 lbs/ 5.4 kg

KNOW YOUR FOOT & CALF MASSAGER

Nekteck Shiatsu Foot & Calf Massager with Heat combines the shiatsu massage with heat therapy to relieve tension and fatigue for your feet and calves. It features an adjustable bar and adjustable feet to position the massager at different angles to fit your needs. Enjoy the comfortable massage time with Nekteck Shiatsu Foot & Calf Massager with Heat.

PARTS & FEATURES

NO PART NAME FEATURE
1 Rolling Area Combine rolling, kneading, and scraping functions to offer

you optimum massage experiences
2| Vibrating Area| Focus on massaging your heels with vibrations
3| Control Panel| Press the buttons to choose your preferred massage modes and intensity levels, or turn on/off the massager
4| Airbags| Provide air pressure by inflating and deflating the airbags
5| Removable & Washable Covers| For easy cleaning
6| Adjustable Bar| Position the massager at an angle of about 54° for calf massage when you are sitting.

NOTE: The adjustable bar can NOT be used to carry the massager

7| Adjustable Feet| Position the massager at an angle of about 20° for a sole massage when you are sitting, or calf massage when you are lying down
8| Anti-slip Foot Pads| Make the massager more stable while operating
9| Handle| Designed on both left and right sides for better portability

WIRELESS REMOTE CONTROLLER

CONTROL PANEL

OPERATING INTRODUCTIONS

SETTING UP
  • Remove all packing material from the massager, and make sure there is no packaging underneath or around the massager. Check if there are any parts damaged or missing during transportation.
  • Place the massager on a flat floor or surface.
  • Unwind and plug the power cord into the power jack on the side of the massager.
  • Connect the power adapter to the socket, then the ON/OFF Button starts to flash.

Now your shiatsu foot & calf massager is ready for use.

MASSAGE OPERATION
  • Step 1: Turn on the massager
    Press the ON/OFF Button “@” on the controller or the control panel. The massager will beep once and start in the default massage mode (see the chart below).
    Default Settings for Each Mode and Timer

  • Step 2: Adjust the massage modes and intensity levels to fit your needs (Optional)
    Reference Chart of Modes and Intensity Levels
    Press the Mode Buttons “§ (ff[) @ @ “to change the intensity levels or turn on/off the corresponding mode. With each press of the button, the intensity level will change once, cycling through the sequence shown in the chart above.
    For example: Press the Rolling Button “@ ” once, the intensity will change to the next level, cycling through the following sequence: Low Intensity (Default Setting with Green Indicator)➔ High Intensity (Red Indicator)➔ OFF (Light Off).
    Each of the 4 massage modes can be adjusted and run individually.
    Reference Chart of Indicator Light Color and Its Corresponding Intensity Level or Timer

  • Step 3: Set the Massage Duration (Optional)
    By default, this massager will automatically shut off after a 15-min massage session. Press the Timer Button II G II to switch the timer between 15 and 30 mins. (9 15 Mins (Default)  G 30 Mins
    Note: If you want to have a 30-min massage session instead of the default 15 mins session, it’s highly recommended to set the time in the beginning. If you want to change the time during the operation, please follow the chart below.

Cautions

  • After each massage session, please rest for 30 minutes before starting the next massage session.
  • Each Individual should NOT use the massager for over 45 minutes a day.
  • It is highly recommended to start the operation from the lowest intensity at the beginning of each use.
  • It is highly recommended to wear socks while using this massager.
  •  If you want to stop the massage session, press the ON/OFF button at any time you like.

SWITCH/CHANGE THE TIME

| WHEN THE MASSAGER WORKED FOR|

HOW THE TIMER CONTINUES TO WORK AFTER SWITCHING

|

EXAMPLES

|

EXPLANATION

---|---|---|---|---
From 15 to

30 mins

| 0-15 mins| The previous working time will NOT be cleared and will be accumulated to the 30-min session. If you want to have another exact 30-min session during the operation, turn off and on the massager and set the modes and time again.| When Massager has worked for| 10 mins| If you switch from 15 mins to 30 mins when the massager has worked for 10 minutes, it will continue to work for 20 minutes, not another 30 minutes
Remaining working time after switching| 20 mins
From 30 to

15 mins

| < 15 mins| The previous working time will NOT be cleared and will be accumulated to the 15-min session.|

When Massager has worked for

|

5 mins

| If you switch from 30 mins to 15 mins when the massager has worked for 5 minutes, it will continue to work for 10 minutes, not another 15 minutes.
Remaining working time after switching| 10 mins
15 mins| The massager will still run through the previous 30-min session. In this situation, please turn off and restart the massager to run the 15-min massage session.| When Massager has worked for| 25 mins| If you switch from 30 mins to 15 mins when the massager has worked for 25 minutes, it will continue to work for only 5 minutes, not another 15 minutes.
Remaining working time after switching|

5 mins

CLEANING AND MAINTENANCE

TO CLEAN
  • Unplug the massager and allow it to cool down before cleaning.
    The fabric cover can be removed for cleaning.

  • Clean the base only with a soft, very slightly damp sponge or cloth.

  • DO NOT allow water or any other liquids to get into the massager.

  • DO NOT immerse the product in any liquid to clean.

  • DO NOT use abrasive cleaners, brushes, or strong chemicals to clean the product, for it might cause damage to the product.

TO STORE
  • Place the massager in its package box or a safe, dry, and cool place.
  • Avoid sharp edges and objects to protect the product from scratching or damaging.
  • DO NOT wrap the power cord around the product to avoid breakage.
  • Keep out of high temperatures.

TROUBLESHOOTING

Troubleshoot your problem by using the chart below. If the Shiatsu Foot & Calf Massager still does not operate correctly, it may be defective. Please contact a qualified technician. DO NOT try to repair it by yourself. Other­wise, there is a risk of electric shock.
Customer Support:
If you believe you received a defective unit, please contact our Customer Service Team at support@nekteck.com for a solution.

PROBLEM POSSIBLE CAUSE SOLUTION
The product does not work The adapter is not plugged properly Plug in again
The ON/OFF button is not pressed Press the ON/OFF button
The adapter is not the original one Check whether the adapter specifications

are the same as the original adapter: 12V SA
The product suddenly stops working| The product turns off automatically after a 15-min or 30-min session| Press the ON/OFF button again for another session
The DC connector is not connected properly to the DC power jack| Check and reconnect the connector and jack port
The product is overused and the overheat protection turns on| Unplug the product and let it cool down completely before using it again
The device is pressed too hard and the massage rollers get stuck| Press the ON/OFF button to restart the product
The heat function does not work| The heat button is not pressed| Press the Heat Button
The product is abnormally warm| The product is likely to be overused| Unplug the product and let it cool down completely before using it again

LIMITED WARRANTY

Nekteck provides all of our customers with a warranty of 12 Months from the date of purchase. Please contact our customer service team at support@nekteck.com if you have any questions.
Order ID: __ _
Date of Purchase: __ _
For your own reference, we recommend that you record your order number and date of purchase.

DISCLAIMER

Nekteck and its subsidiaries assume no liability for damage caused by the use of the product other than for its intended use or as instructed in the user manual. Some countries or states do not allow this exclusion or limitation of incidental or consequential losses so the foregoing disclaimer may not apply to you.
IMPROPER USE OF NEKTECK’S PRODUCTS INVOLVES SERIOUS RISKS INCLUDING INJURY AND DISABILITY. YOU UNDERSTAND THAT BY KEEPING, USING, OR ALLOWING USE OF NEKTECK’S PRODUCTS, YOU AGREE TO THE FOLLOWING:

  1. NEKTECK ACCEPTS NO RESPONSIBILITY FOR ANY INJURY WHICH MIGHT OCCUR WHILE USING NEKTECK’S PRODUCTS.
  2. USE LIMITATION. YOU MAY NOT MODIFY AND REPRODUCE NEKTECK’S PRODUCTS. YOU SHALL CAREFULLY INSPECT NEKTECK’S PRODUCTS BEFORE EACH USE TO ENSURE IT HAS NOT BEEN DAMAGED AND IS FULLY FUNCTIONAL.

CUSTOMER SUPPORT

Feel free to contact our friendly Customer Support Team if you have any questions or concerns regarding your new product. Your satisfaction is our priority.
Email: support@nekteck.com
W We will reply to your message within 24 hours!
Please include your Order ID in your email when you are contacting Customer Support for faster solutions.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Compliance Statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
SDoC
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier
Trade Name: NEKTECK
Model No.: NK-FLM02
Responsible Party- U.S. Contact Information
US Company Name: NEKTECK INC
Address: 556 Vanguard Way Ste C, Back Door #7 Brea, CA, USA 92821 Telephone number or internet contact
information: zhonghuanqin@nekteck.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals